循环动载边界下三维粗糙节理面剪切力学响应研究

doi:10.13722/j.cnki.jrme.2023.0903

Abstract
Figure/Table
References (0)
Related Citation (15)

Download: PDF (10394 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract Shear tests of three-dimensional rough joint surfaces were conducted under superimposed actions of sinusoidal cyclic normal dynamic loads and sinusoidal cyclic shear displacements. The effects of initial normal static load( )，dynamic normal load amplitude( )，dynamic normal load frequency( ) and the number of shear cycles (N) on the shear properties were explored. With an increasing of or ，the variation range of the normal load for the joint surfaces gradually increases. Within a shear displacement cycle，the shear load experiences a variation of fluctuating increase→fluctuating decrease→fluctuating increase. The peak shear load in stable states increases by 4.90 times and 65.12%，respectively，with an increasing of and ，implying a gradually enhanced shear resistance capacity. However，as increases，the progressive accumulation of damage on the joint surfaces results in a gradual reduction in the peak shear load，and the moment when the peak shear load occurs gradually moves forward. The peak shear load in stable states decreases by 17.49%. Within a shear displacement cycle，the normal displacement of joint surfaces shows a variation trend of fluctuating increase→fluctuating decrease→secondary increase→secondary decrease. When the joint surface shears away from the initial position，the continuous “climbing effects” of the surface asperities lead to a gradual increase in the normal displacement. A significant negative correlation between the normal displacement and normal load for the joint surfaces is recognized，and the maximum normal displacement lags behind the maximum shear displacement by a quarter of a normal load period. As N increases，the continuous wear and deterioration of the joint surfaces lead to an exponential decrease in the maximum normal displacement. The maximum normal displacement exhibits change characteristics of gradually decreasing with ，gradually increasing with ，and initially increasing and then decreasing with ，respectively. The surface roughness coefficients of joints after shearing decrease by 57.79% and 43.26% with and respectively，while shows a variation of first increasing and then decreasing with at 1 Hz as the inflection point.

Key words： rock mechanics rough joint surface cyclic shear normal dynamic load normal deformation surface wear

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors

Cite this article:

URL:

http://rockmech.whrsm.ac.cn/EN/10.13722/j.cnki.jrme.2023.0903 OR http://rockmech.whrsm.ac.cn/EN/Y2024/V43/I5/1176

[2]	TANG Z C，WONG L N Y. New criterion for evaluating the peak shear strength of rock joints under different contact states[J]. Rock Mechanics and Rock Engineering，2016，49：1 191-1 199.
[4]	王培涛，黄正均，任奋华，等. 基于3D打印的含复杂节理岩石直剪特性及破坏机制研究[J]. 岩土力学，2020，41(1)：46-56.(WANG Peitao，HUANG Zhengjun，REN Fenhua，et al. Research on direct shear behaviour and fracture patterns of 3D-printed complex jointed rock models[J]. Rock and Soil Mechanics，2020，41(1)：46-56.(in Chinese))
[7]	LEE Y K，PARK J W，SONG J J. Model for the shear behavior of rock joints under CNL and CNS conditions[J]. International Journal of Rock Mechanics and Mining Sciences，2014，70：252-263.
[8]	崔国建，张传庆，韩华超，等. CNL及CNS条件下结构面剪切特性试验研究[J]. 岩石力学与工程学报，2019，38(增2)：3 384-3 392. (CUI Guojian，ZHANG Chuanqing，HAN Huachao，et al. Experiment study on shear behavior of artificial joint under CNL and CNS boundary conditions[J]. Chinese Journal of Rock Mechanics and Engineering，2019，38(Supp.2)：3 384-3 392.(in Chinese))
[10]	周辉，程广坦，朱勇，等. 大理岩规则齿形结构面剪切特性试验研究[J]. 岩土力学，2019，40(3)：852-860.(ZHOU Hui，CHENG Guangtan，ZHU Yong，et al. Experimental study of shear deformation characteristics of marble dentate joints[J]. Rock and Soil Mechanics，2019，40(3)：852-860.(in Chinese))
[12]	刘新荣，许彬，周小涵，等. 软硬互层岩体结构面宏细观剪切力学特性[J]. 煤炭学报，2021，46(9)：2 895-2 909.(LIU Xinrong，XU Bin，ZHOU Xiaohan，et al. Investigation on the macro-meso shear mechanical properties of soft-hard interbedded rock discontinuity[J]. Journal of China Coal Society，2021，46(9)：2 895-2 909.(in Chinese))
[5]	李海波，蒋会军，赵坚，等. 动荷载作用下岩体工程安全的几个问题[J]. 岩石力学与工程学报，2003，22(11)：1 887-1 891.(LI Haibo，JIANG Huijun，ZHAO Jian，et al. Some problems about safety analysis of rock engineering under dynamic load[J]. Chinese Journal of Rock Mechanics and Engineering，2003，22(11)：1 887-1 891.(in Chinese))
[14]	刘博，李海波，刘亚群. 循环剪切荷载作用下岩石节理变形特性试验研究[J]. 岩土力学，2013，34(9)：2 475-2 481.(LIU Bo，LI Haibo，LIU Yaqun. Experimental study of deformation behavior of rock joints under cyclic shear loading[J]. Rock and Soil Mechanics，2013，34(9)：2 475-2 481.(in Chinese))
[15]	HAN G S，JING H，JIANG Y，et al. Effect of cyclic loading on the shear behaviours of both unfilled and infilled rough rock joints under constant normal stiffness conditions[J]. Rock Mechanics and Rock Engineering，2020，53：31-57.
[17]	刘日成，尹乾，杨瀚清，等. 恒定法向刚度边界条件下三维粗糙节理面循环剪切力学特性[J]. 岩石力学与工程学报，2021，40(6)：1 092-1 109.(LIU Richeng，YIN Qian，YANG Hanqing，et al. Cyclic shear mechanical properties of 3D rough joint surfaces under constant normal stiffness(CNS) boundary conditions[J]. Chinese Journal of Rock Mechanics and Engineering，2021，40(6)：1 092-1 109.(in Chinese))
[20]	ZHU Q，YIN Q，HUANG N，et al. Assessment of nonlinear flow behaviors through real rough rock fractures during shearing[J]. Geomechanics and Geophysics for Geo-Energy and Geo-Resources，2022，8：171.
[22]	BANDIS S C，LUMSDEN A C，BARTON N R. Fundamentals of rock joint deformation[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts，1983，20(6)：249-268.
[25]	吴顺川，高艳华，李永兵，等. 法向循环加卸载条件下节理力学特征研究[J]. 岩石力学与工程学报，2015，34(增2)：3 683-3 693.(WU Shunchuan，GAO Yanhua，LI Yongbing，et al. A study of mechanical properties of joint under normal cyclic loading/unloading[J]. Chinese Journal of Rock Mechanics and Engineering，2015，34(Supp.2)：3 683-3 693.(in Chinese))
[3]	宋洋，范波，王贺平. 考虑法向应力与岩石强度的加锚节理岩体剪切力学模型研究[J]. 岩石力学与工程学报，2023，42(6)：1 325-1 335.(SONG Yang，FAN Bo，WANG Heping. Research on shear mechanics model of anchored-jointed rock mass considering normal stress and rock strength[J]. Chinese Journal of Rock Mechanics and Engineering，2023，42(6)：1 325-1 335.(in Chinese))
[13]	蒋宇静，张孙豪，栾恒杰，等. 恒定法向刚度边界条件下锚固节理岩体剪切特性试验研究[J]. 岩石力学与工程学报，2021，40(4)：663-675.(JIANG Yujing，ZHANG Sunhao，LUAN Hengjie，et al. Experimental study on shear characteristics of bolted rock joints under constant normal stiffness boundary conditions[J]. Chinese Journal of Rock Mechanics and Engineering，2021，40(4)：663-675.(in Chinese))
[23]	李博，崔逍峰，莫洋洋，等. 法向应力作用下砂岩错位裂隙变形行为研究[J]. 岩土力学，2021，42(7)：1 850-1 860.(LI Bo，CUI Xiaofeng，MO Yangyang，et al. Deformation behavior of dislocated sandstone fractures subject to normal stresses[J]. Rock and Soil Mechanics，2021，42(7)：1 850-1 860.(in Chinese))
[1]	陈家嵘，周昌台，周韬，等. 压剪荷载下含单一裂隙砂岩的应变演化与破坏特征研究[J]. 岩石力学与工程学报，2023，42(7)：1 743-1 758.(CHEN Jiarong，ZHOU Changtai，ZHOU Tao，et al. Experimental study on strain evolution and failure behavior of sandstone containing a single pre-existing flaw under compressive-shear loading[J]. Chinese Journal of Rock Mechanics and Engineering，2023，42(7)：1 743- 1 758.(in Chinese))
[11]	尹乾，靖洪文，孟波，等. 恒定法向刚度条件下三维粗糙裂隙面剪切力学特性[J]. 岩石力学与工程学报，2020，39(11)：2 213-2 225.(YIN Qian，JING Hongwen，MENG Bo，et al. Shear mechanical properties of 3D rough rock fracture surfaces under constant normal stiffness conditions[J]. Chinese Journal of Rock Mechanics and Engineering，2020，39(11)：2 213-2 225.(in Chinese))
[21]	RONG G，YANG J，CHENG L，et al. Laboratory investigation of nonlinear flow characteristics in rough fractures during shear process[J]. Journal of Hydrology，2016，541：1 385-1 394.
[9]	MENG F Z，LOUIS NGAI Y W，ZHOU H，et al. Shear rate effects on the post-peak shear behaviour and acoustic emission characteristics of artificially split granite joints[J]. Rock Mechanics and Rock Engineering，2019，52：2 155-2 174.
[19]	DANG W G，TAO K，CHEN X F. Frictional behavior of planar and rough granite fractures subjected to normal load oscillations of different amplitudes[J]. Journal of Rock Mechanics and Geotechnical Engineering，2022，14(3)：746-756.
[6]	黄锋，周洋，彭焱森，等. 循环荷载下花岗岩强度及变形特征试验研究[J]. 地下空间与工程学报，2021，17(2)：356-364.(HUANG Feng，ZHOU Yang，PENG Yansen，et al. Study on the strength and deformation characteristics of granite under cyclic loading[J]. Chinese Journal of Underground Space and Engineering，2021，17(2)：356-364.(in Chinese))
[16]	GUO H L，WANG G，LUO Y，et al. Shear failure and mechanical behaviors of granite with discontinuous joints under dynamic disturbance：laboratory tests and numerical simulation[J]. Archives of Civil and Mechanical Engineering，2023，23：171.
[18]	DANG W G，KONIETZKY H，FRUHWIRT T，et al. Cyclic frictional responses of planar joints under cyclic normal load conditions：laboratory tests and numerical simulations[J]. Rock Mechanics and Rock Engineering，2020，53(1)：337-364.
[24]	MIRZAGHORBANALI A，NEMCIK J，AZIA N. Effects of cyclic loading on the shear behaviour of infilled rock joints under constant normal stiffness conditions[J]. Rock Mechanics and Rock Engineering，2014，47：1 373-1 391.