法向动载条件下粗糙岩质节理面剪切力学特性试验研究

doi:10.13722/j.cnki.jrme.2023.1142

Abstract
Figure/Table
References (0)
Related Citation (15)

Download: PDF (5142 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract To explore the load-bearing characteristics of the rock joints under seismic loads，the shear experiments about the mechanical behaviors of a rough joint surface under the dynamic normal load stress were carried out. The influence of the amplitude and frequency of the dynamic normal load on the intensity parameters，morph parameters and failure characteristics of the joint surface were obtained. The results show that：(1) Increasing the dynamic load amplitude results in a linear decrease of 48.27% to 55.59% in the peak shear strength. The dynamic load frequency has less impact on the peak shear strength. In the stable residual stage，the shear stress amplitude width increases linearly by 1.24 to 2.83 times with increasing the amplitude，and the dynamic loading frequency increases from 0.2 Hz to 0.5 Hz，resulting in a rapid decrease of 36.28% to 40.61% in the shear stress amplitude. This decline continues gradually after the frequency exceeds 0.5 Hz. (2) The shear stiffness in the pre-peak stage is a normal stress-dependent. And，both the amplitude and frequency of the dynamic normal load decrease the shear stiffness in the pre-peak stage and dilatancy in the post-failure stage. (3) A significant phase shift between the shear stress and normal stress occurs. The phase offset decreases with the increase of the amplitude and frequency of the dynamic normal stress. When the frequency reaches 2.0 Hz，the phase shift becomes negligible. (4) When the frequency is below 0.5 Hz，the proportion of the joint surface wear area increases sharply by 36.10% to 69.37%. Conversely，when the frequency exceeds 0.5 Hz，the wear area proportion shows an approximately linear increase of 5.17% to 10.18%.

Key words： rock mechanics joint dynamic normal load shear stress mechanical behavior

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	DAI Wanli1
	2
	ZHANG Qiang1
	2
	GU Qiuxin1
	2
	YE Sizhe1
	2
	LI Tao1
	2
	SHI Linpo1
	2
	HAN Guilei1
	3
	XU Dingping4

Cite this article:

DAI Wanli1,2,ZHANG Qiang1, et al. Experimental study on the shear mechanical behaviors of a rough rock joint surface under dynamic normal load boundary condition[J]. , 2024, 43(7): 1751-1762.

URL:

http://rockmech.whrsm.ac.cn/EN/10.13722/j.cnki.jrme.2023.1142 OR http://rockmech.whrsm.ac.cn/EN/Y2024/V43/I7/1751

[11]	STEIN R S. The role of stress transfer in earthquake occurrence[J]. Nature(London)，1999，402(6762)：605-609.
[12]	DANG W，KONIETZKY H，FRUEHWIRT T. Direct shear behavior of a plane joint under dynamic normal load(DNL) conditions[J]. Engineering Geology，2016，213：133-141.
[3]	周辉，孟凡震，张传庆，等. 结构面剪切破坏特性及其在滑移型岩爆研究中的应用[J]. 岩石力学与工程学报，2015，34(9)：1 729-1 738.(ZHOU Hui，MENG Fanzhen，ZHANG Chuanqing，et al. Characteristics of shear failure of structural plane and slip rockburst[J]. Chinese Journal of Rock Mechanics and Engineering，2015，34(9)：1 729-1 738.(in Chinese))
[13]	LIU E，HUANG R，HE S. Effects of frequency on the dynamic properties of intact rock samples subjected to cyclic loading under confining pressure conditions[J]. Rock Mechanics and Rock Engineering，2012，45(1)：89-102.
[23]	HUANG N，LIU R，JIANG Y，et al. Effects of fracture surface roughness and shear displacement on geometrical and hydraulic properties of three-dimensional crossed rock fracture models[J]. Advances in Water Resources，2018，113：30-41.
[8]	尹乾，靖洪文，孟波，等. 恒定法向刚度条件下三维粗糙裂隙面剪切力学特性[J]. 岩石力学与工程学报，2020，39(11)：2 213-2 225.(YIN Qian，JING Hongwen，MENG Bo，et al. Shear mechanical properties of 3D rough rock fracture surfaces under constant normal stiffness conditions[J]. Chinese Journal of Rock Mechanics and Engineering，2020，39(11)：2 213-2 225.(in Chinese))
[10]	田世轩，郭保华，孙杰豪，等. 不同边界条件下剪切速率对类岩石节理剪切力学特性的影响[J]. 岩土力学，2023，44(2)：541-551. (TIAN Shixuan，GUO Baohua，SUN Haojie，et al. Effect of shear rate on shear mechanical properties of rock-like joints under different boundary conditions[J]. Rock and Soil Mechanics，2023，44(2)：541-551.(in Chinese))
[15]	DANG W，KONIETZKY H，FRÜHWIRT T. Direct shear behavior of planar joints under cyclic normal load conditions：effect of different cyclic normal force amplitudes[J]. Rock Mechanics and Rock Engineering，2017，50(11)：3 101-3 107.
[18]	DANG W，KONIETZKY H. The effect of normal load oscillation amplitude on the frictional behavior of a rough basalt fracture[J]. Rock Mechanics and Rock Engineering，2022，55(6)：3 385-3 397.
[20]	袁伟，李建春. 剪切速率对平直节理摩擦行为的影响及其机制研究[J]. 岩石力学与工程学报，2021，40(增2)：3 241-3 252.(YUAN Wei，LI Jianchun. Study on the effects and its mechanism of shear rate on friction of planar joints[J]. Chinese Journal of Rock Mechanics and Engineering，2021，40(Supp.2)：3 241-3 252.(in Chinese))
[25]	韩钢. 白鹤滩水电站层间错动带剪切特性研究[硕士学位论文][D]. 武汉：湖北工业大学，2019.(HAN Gang. Shearing behaviors of interlayer staggered zones at Baihetan Hydropower Station[M. S. Thesis][D]. Wuhan：Hubei University of Technology，2019.(in Chinese))
[28]	FANG Y，ELSWORTH D，WANG C，et al. Frictional stability-permeability relationships for fractures in shales[J]. Journal of Geophysical Research，2017，122(3)：1 760-1 776.
[1]	尹乾，靖洪文，孟波，等. CNL和CNS边界条件下砂岩宏细观剪切力学特性[J]. 采矿与安全工程学报，2021，38(3)：615-624.(YIN Qian，JING Hongwen，MENG Bo，et al. Macroscopic and microscopic shear mechanical properties of sandstone under CNL and CNS boundary conditions[J]. Journal of Mining and Safety Engineering，2021，38(3)：615-624.(in Chinese))
[9]	刘日成，尹乾，杨瀚清，等. 恒定法向刚度边界条件下三维粗糙节理面循环剪切力学特性[J]. 岩石力学与工程学报，2021，40(6)：1 092-1 109.(LIU Richeng，YIN qian，YANG Hanqing，et al. Cyclic shear mechanical properties of 3D rough joint surfaces under constant normal stiffness(CNS) boundary conditions[J]. Chinese Journal of Rock Mechanics and Engineering，2021，40(6)：1 092-1 109.(in Chinese))
[19]	崔国建，张传庆，周辉，等. 动力扰动作用下多功能岩石结构面剪切试验装置研制与应用研究[J]. 岩土力学，2022，43(6)：1 727-1 737.(CUI Guojian，ZHANG Chuanqing，ZHOU Hui，et al. Development and application of multifunctional shear test apparatus for rock discontinuity under dynamic disturbance loading[J]. Rock and Soil Mechanics，2022，43(6)：1 727-1 737.(in Chinese))
[2]	曹平，龙龙，范文臣，等. 基于起伏形态特征的节理岩石峰值剪切强度准则[J]. 中南大学学报：自然科学版，2017，48(4)：1 081-1 087.(CAO Ping，LONG Long，FAN Wenchen，et al. Peak shear strength criterion for rock joints based on undulating characteristics[J]. Journal of Central South University：Science and Technology，2017，48(4)：1 081-1 087.(in Chinese))
[4]	宋宇，刘保国，任大瑞，等. 基于分形理论构建随机粗糙节理模型的方法研究[J]. 岩石力学与工程学报，2021，40(1)：101-112.(SONG Yu，LIU Baoguo，REN Darui，et al. Study on stochastic method for modeling rough joints based on fractal theory[J]. Chinese Journal of Rock Mechanics and Engineering，2021，40(1)：101-112.(in Chinese))
[5]	焦峰，许江，彭守建，等. 常法向刚度条件下人工结构面剪切力学特性及损伤演化规律试验研究[J]. 煤炭学报，2023，48(11)：4 065-4 077.(JIAO Feng，XU Jiang，PENG Shoujian，et al. Experimental study on shear mechanical properties and damage evolution of artificial structural plane under condition normal stiffness[J]. Journal of China Coal Society，2023，48(11)：4 065- 4 077.(in Chinese))
[7]	崔国建，张传庆，韩华超，等. CNL及CNS条件下结构面剪切特性试验研究[J]. 岩石力学与工程学报，2019，38(增2)：3 384-3 392. (CUI Guojian，ZHANG Chuanqing，HAN Huachao，et al. Experiment study on shear behavior of artificial joint under CNL and CNS boundary conditions[J]. Chinese Journal of Rock Mechanics and Engineering，2019，38(Supp.2)：3 384-3 392.(in Chinese))
[6]	SHRIVASTAVA A K，RAO K S. Shear behaviour of rock joints under CNL and CNS boundary conditions[J]. Geotechnical and Geological Engineering，2015，33(5)：1 205-1 220.
[16]	DANG W，CHEN J，HUANG L，et al. Frictional behavior of granular materials exposed to dynamic normal load[J]. Engineering Geology，2021，295：106414.
[21]	孙杰豪，郭保华，田世轩，等. 峰前循环剪切作用下岩石节理剪切力学特性[J]. 岩土力学，2022，43(增2)：52-62.(SUN Jiehao，GUO Baohua，TIAN Shixuan，et al. Shear mechanical properties of rock joints under pre-peak cyclic shearing condition[J]. Rock and Soil Mechanics，2022，43(Supp.2)：52-62.(in Chinese))
[26]	梁昌玉，李晓，李守定，等. 岩石静态和准动态加载应变率的界限值研究[J]. 岩石力学与工程学报，2012，31(6)：1 156-1 161. (LIANG Changyu，LI Xiao，LI Shouding，et al. Study of strain rates threshold value between static loading and quasi-dynamic loading of rock[J]. Chinese Journal of Rock Mechanics and Engineering，2012，31(6)：1 156-1 161.(in Chinese))
[14]	DANG W，KONIETZKY H，LIFU C，et al. Velocity-frequency-amplitude-dependent frictional resistance of planar joints under dynamic normal load(DNL) conditions[J]. Tunnelling and Underground Space Technology，2018，79：27-34.
[17]	DANG W，LIU Y，LI S，et al. Direct shear behavior of dredged soil under dynamic normal load conditions[J]. Soil Dynamics and Earthquake Engineering，2023，168(5)：107851.
[22]	沈明荣，张清照. 规则齿型结构面剪切特性的模型试验研究[J]. 岩石力学与工程学报，2010，29(4)：713-719.(SHEN Mingrong，ZHANG Qingzhao. Experimental study of shear deformation characteristics of rock mass discontinuities[J]. Chinese Journal of Rock Mechanics and Engineering，2010，29(4)：713-719.(in Chinese))
[24]	RONG G，YANG J，CHENG L，et al. Laboratory investigation of nonlinear flow characteristics in rough fractures during shear process[J]. Journal of Hydrology，2016，541：1 385-1 394.
[27]	LEE Y K，PARK J W，SONG J J. Model for the shear behavior of rock joints under CNL and CNS conditions[J]. International Journal of Rock Mechanics and Mining Sciences，2014，70：252-263.