|
|
|
| CALCULATION METHOD FOR THREE-DIMENSIONAL COMPOSITE TOPOGRAPHY OF JOINT UNDER DIFFERENT CONTACT CONDITIONS |
| (1. Key Laboratory of Geotechnical and Underground Engineering of Ministry of Education，Tongji University，Shanghai 200092，China；2. Department of Geotechnical Engineering，Tongji University，Shanghai 200092，China；3. Construction Safety and Quality Supervision Station，Minhang Sub-station，Shanghai 201100，China；4. China Railway Eryuan Engineering Group Co.， Ltd.，Chengdu，Sichuan 610031，China) |
|
|
|
|
Abstract The mechanical and flow characteristics of rock joint are closely associated with its three-dimensional topography. For a single rock joint，the roughness and waviness of its surface is of paramount importance to flow；and the flow characteristics are related not only to the topography of a single joint surface，but also to the composite topography of the upper and lower joint surfaces. Different contact condition results in different composite topography. The analysis of joint composite topography is the basis of research on flow in a single rock joint. In order to compute the three-dimensional composite topography effectively，the conditions for determining stable contact of two joint surfaces are presented；and the contact algorithm based on determinant conditions is introduced. The Visual C++ programming language is adopted to provide a procedure for three-dimensional composite topography calculation. By using the procedure，the composite topography of joint under different contact conditions can be calculated conveniently with the surface topography data derived from TJXW–3D portable rock surface topography laser scanner developed by Tongji University. Then the fresh marble tension joint is taken as an object；and different contact conditions are formed by dislocating the upper joint surface from the lower joint surface for 1，2，3，4，5 mm respectively after scanning the joint surfaces by TJXW–3D topography scanner. Based on topography data，the composite topography parameters under different contact conditions are calculated by the procedure proposed above；and the influence of different contact conditions on joint composite topography is discussed，which provides a foundation for researches on the relations between three-dimensional composite topography and the mechanical and flow properties of joint under different contact conditions.
|
|
Received: 05 February 2010
|
|
|
|
| [1] ZHAO J. The joint matching coefficient(JMC) of rock joints[C]// Proceedings of the Symposium on Tunnelling for Water Resources and Power Projects. New Dehil：[s. n.]，1988：21–27.
[2] ZHAO J. Joint surface matching and shear strength part B：JRC-JMC shear strength criterion[J]. International Journal of Rock Mechanics and Mining Sciences，1997，34(2)：179–185.
[3] 赵 坚. 岩石节理剪切强度的JRC-JMC新模型[J]. 岩石力学与工程学报，1998，17(4)：349–357.(ZHAO Jian. A new shear strength criterion for rock joint[J]. Chinese Journal of Rock Mechanics and Engineering，1998，17(4)：349–357.(in Chinese))
[4] 赵 坚. 岩石节理吻合系数及其对节理特性的影响[J]. 岩石力学与工程学报，1997，16(6)：514–521.(ZHAO Jian. Joint matching coefficient and its effects on behavior of rock joint[J]. Chinese Journal of Rock Mechanics and Engineering，1997，16(6)：514–521.(in Chinese))
[5] ZHAO J. Joint surface matching and shear strength part A：joint matching coefficient(JMC)[J]. International Journal of Rock Mechanics and Mining Sciences，1997，34(2)：173–178.
[6] GRASSELLI G. Shear strength of rock joints based on quantified surfaces description[J]. Rock Mechanics and Rock Engineering，2006，39(4)：295–314.
[7] GRASSELI G J，WIRTH P E. Quantitative three-dimensional description of a rough surface and parameter evolution with shearing[J]. International Journal of Rock Mechanics and Mining Sciences，2002，39(6)：789–800.
[8] GRASSELI G，EGGER P. Constitutive law for the shear strength of rock joints based on three-dimensional surface parameters[J]. International Journal of Rock Mechanics and Mining Sciences，2003，40(1)：25–40.
[9] 夏才初，孙宗颀，潘长良. 节理接触机制与闭合性质研究[J]. 同济大学学报，1995，23(2)：147–152.(XIA Caichu，SUN Zongqi，PAN Changliang. Study of contact mechanism and closure behavior of rock joints[J]. Journal of Tongji University，1995，23(2)：147–152.(in Chinese))
[10] 夏才初. 岩石表面形貌学与节理力学研究[博士学位论文][D]. 长沙：中南大学，1992.(XIA Caichu. Study of rock surface topography and joint mechanical properties[Ph. D. Thesis][D]. Changsha：Central South University，1992.(in Chinese))
[11] 夏才初. 工程岩体节理力学[M]. 上海：同济大学出版社，2002.(XIA Caichu. Engineering rock mass joint mechanics[M]. Shanghai：Tongji University Press，2002.(in Chinese))
[12] TSANG Y W，TSANG C F. Channel model of flow through fractured media[J]. Water Resources Research，1987，23(3)：467–479.
[13] 周创兵，叶自桐，韩 冰. 岩石节理形态与水力特性研究[J]. 水科学进展，1997，8(3)：233–239.(ZHOU Chuangbing，YE Zitong，HAN Bing. A study of configuration and hydraulic conductivity of rock joints[J]. Advances in Water Science，1997，8(3)：233–239.(in Chinese))
[14] GRASSELLI G. Shear strength of rock joints based on quantified surface description[Ph. D. Thesis][D]. Lausanne：Swiss Federal Institute of Technology Lausanne(EPFL)，2001.
[15] JIANG Y J，LI B，YOSIHIKO T. Estimating the relation between surface roughness and mechanical properties of rock joints[J]. International Journal of Rock Mechanics and Mining Sciences，2006，43(6)：837–846.
[16] 夏才初，王 伟，丁增志. TJXW–3D型便携式岩石三维表面形貌仪的研制[J]. 岩石力学与工程学报，2008，27(7)：1 505–1 512.(XIA Caichu，WANG Wei，DING Zengzhi. Development of three- dimensional TJXW–3D-typed portable rock surface topography scanner[J]. Chinese Journal of Rock Mechanics and Engineering，2008，27(7)：1 505–1 512.(in Chinese))
[17] 丁增志. 节理表面形貌研究及在非贯通节理岩体强度准则中的应用[硕士学位论文][D]. 上海：同济大学，2007.(DING Zengzhi. Study of the joint surface topography and application in strength criterion of rock mass containing discontinuous joints[M. S. Thesis][D]. Shanghai：Tongji University，2007.(in Chinese))
[18] 费燕琼，赵锡芳. 基于凸多面体边界元的接触状态判断[J]. 机械工程学报，2005，41(1)：50–53.(FEI Yanqiong，ZHAO Xifang. Judge assembly contact states based on boundary component of convex polyhedron[J]. Chinese Journal of Mechanical Engineering，2005，41(1)：50–53.(in Chinese))
[19] 费燕琼. 机器人装配操作过程的分析和建模[博士学位论文][D]. 上海：上海交通大学，2002.(FEI Yanqiong. Modeling and analyzing for robotic assembly manipulation process[Ph. D. Thesis][D]. Shanghai：Shanghai Jiaotong University，2002.(in Chinese))
[20] STOUT K F，BLUNT L. Three-dimensional surface topography[M]. 2nd ed. London：Penton Press，2000.
[21] 李成贵，董 申. 三维表面微观形貌的表征参数和方法[J]. 宇航计测技术，1999，19(6)：33–43.(LI Chenggui，DONG Shen. The parameters and methods of characterizing 3D surface microtopography[J]. Journal of Astronautic Metrology and Measurement，1999，19(6)：33–43.(in Chinese)) |
|
|
|
2010, Vol. 29 
