|
|
|
| QUANTITATIVE DETERMINING THE CRACK FABRIC OF ROCK |
| LI Xuefeng1，2，WANG Xing1，2，YUAN Qi1，2 |
(1. Institute of Solid Mechanics，Ningxia University，Yinchuan，Ningxia 750021，China；
2. School of Physics and Electrical Information，Ningxia University，Yinchuan，Ningxia 750021，China) |
|
|
|
|
Abstract A tensorial measure，called the crack fabric，defines the geometric distribution of cracks in rock. Based on the theoretical framework for fabric description with the principle of stereology，a quantitative method describing the crack fabric in rock was proposed. The crack tensor was redefined with the normalized quantities. The trace of the redefined tensor is a constant，which brings a great convenience for determining the crack fabric. The plane crack tensor of rock was defined with the test line. The amplitude parameters and the component angle defined with the second invariant and third invariant of the plane crack tensor respectively，which described the degree and the direction of crack anisotropy. The plane distribution of cracks was described with two defined scalar quantity. The three-dimensional orthotropic crack tensors were deduced uniquely with any two amplitude parameters of three orthogonal planes. With the geometry changes of the crack distribution，the orthotropic fabric tensor degenerated naturally into the form of transversely isotropic and isotropic. Verification of coal CT test results showed that the tensor described better the plane distribution of cracks.
|
|
|
|
|
|
| [1] KANATANI K I. Measurement of crack distribution in a rock mass from observation of its surfaces[J]. Soils and Foundations，1985，25(1)：77–83.
[2] NARA Y. Effect of anisotropy on the long-term strength of granite[J]. Rock Mechanics and Rock Engineering，2015，48(3)：959–969.
[3] SANG-EUN L，SANG-HO C，YONG-SEOK S，et al. The effect of microcracks on the mechanical anisotropy of granite[J]. Materials Science Research International，2001，7(1)：7–13.
[4] HILLIARD J E. Determination of structure anisotropy[C]// Stereology. Proc. Second Int. Cong. Stereology. New York：[s. n.]，1967：219–227.
[5] KANATANI K I. Stereological determination of structural anisotropy[J]. International Journal of Engineering Science，1984，22(5)：531–546.
[6] KEN-ICHI K. Procedures for stereological estimation of structural anisotropy[J]. International Journal of Engineering Science，1985，23(5)：587–598.
[7] ODA M. A method for evaluating the effect of crack geometry on the mechanical behavior of cracked rock masses[J]. Mechanics of Materials，1983，2(2)：163–171.
[8] ODA M. Permeability tensor for discontinuous rock masses[J]. Géotechnique，1985，35(4)：483–495.
[9] ODA M，YAMABE T，ISHIZUKA Y，et al. Elastic stress and strain in jointed rock masses by means of crack tensor analysis[J]. Rock Mechanics and Rock Engineering，1993，26(2)：89–112.
[10] ODA M，KATSUBE T，TAKEMURA T. Microcrack evolution and brittle failure of Inada granite in triaxial compression tests at 140 MPa[J]. Journal of Geophysical Research：Solid Earth，2002，107(B10)：ECV 9–1–ECV 9–17.
[11] 周志芳，庄 超，戴云峰，等. 单孔振荡式微水试验确定裂隙岩体各向异性渗透参数[J]. 岩石力学与工程学报，2015，34(2)：271–278.(ZHOU Zhifang，ZHUANG Chao，DAI Yunfeng，et al. Determining anisotropic hydraulic conductivity in fractured rocks based on single-borehole slug tests[J]. Chinese Journal of Rock Mechanics and Engineering，2015，34(2)：271–278.(in Chinese))
[12] .江学良，曹 平，杨 慧，等. 水平应力与裂隙密度对顶板安全厚度的影响[J]. 中南大学学报：自然科学版，2009，40(1)：211–216. (JIANG Xueliang，CAO Ping，YANG Hui，et al. Effect of horizontal stress and rock crack density on roof safety thickness of underground area[J]. Journal of Central South University：Science and Technology，2009，40(1)：211–216.(in Chinese))
[13] 张青成，左建民，毛灵涛. 基于体视学原理的煤岩裂隙三维表征试验研究[J]. 岩石力学与工程学报，2014，33(6)：1 227–1 232. (ZHANG Qingcheng，ZUO Jianmin，MAO Lingtao. Experimental study of three-dimensional characterization of coal fractures based on stereology[J]. Chinese Journal of Rock Mechanics and Engineering，2014，33(6)：1 227–1 232.(in Chinese))
[14] ZHANG Q C，ZUO J M，MAO L T. The study of relationship between rock crack ct image tensor representation sign and its destruction features[J]. Applied Mechanics and Materials，2013，256–259：402–409 |
|
|
|
2015, Vol. 34 
