微观负泊松比锚杆锚固结构面峰前循环剪切疲劳损伤特性研究

doi:10.3724/1000-6915.jrme.2024.0522

Abstract
Figure/Table
References (0)
Related Citation (15)

Download: PDF (3272 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract The shear support performance of 2G-NPR bolts has been verified; however，their damage behavior under fatigue loading remains to be further explored. Through laboratory pre-peak cyclic loading tests，the shear mechanical properties of PR steel(Q235 steel) and 2G-NPR steel bolted rock joints were compared，exploring the effects of different normal stresses，roughness，shear amplitudes，and rates on the shear fatigue damage characteristics of 2G-NPR steel bolted rock joints. The results show that：(1) As the normal stress increases，the shear strength of PR steel bolted rock joints exhibits a marked decrease after an initial increase in the number of cycles，whereas the shear strength of 2G-NPR steel bolted rock joints gradually increases. This trend underscores the significant role of the negative Poisson?s ratio effect in enhancing the shear fatigue performance of the 2G-NPR steel bolts. (2) The peak and residual shear strengths of 2G-NPR steel bolted rock joints significantly increase with higher shear rates and normal stresses，but are less affected by changes in joint surface roughness and shear amplitude. Additionally，the pre-peak shear stiffness of these joints increases with roughness，shear rate，and normal stress，while shear amplitude has only a minor effect. The flexural angle of the anchor rod increases with the roughness，shear amplitude，and shear rate. (3) The ratio of shear force to axial force of 2G-NPR anchor bolts is consistently lower than that of PR anchor bolts under different cyclic loading conditions，indicating that the 2G-NPR bolts can effectively withstand axial force during shear deformation，thus maintaining the stability and support effectiveness of the rock mass. This research offers a valuable reference for the application of 2G-NPR anchor bolts in rock mass support engineering，particularly in regions prone to microseismic activity.

Key words： rock mechanics pre-peak cyclic loading 2G-NPR steel bolted rock joints shear characteristics energy absorption characteristics

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	HUANG Man1
	2
	GUO Zhiwei1
	2
	HONG Chenjie3
	TAO Zhigang3
	HUANG Jin1
	2
	ZHANG He1
	2

Cite this article:

HUANG Man1,2,GUO Zhiwei1, et al. Study on the pre-peak cyclic shear fatigue damage characteristics of 2G-NPR bolted rock joints[J]. , 2025, 44(3): 543-556.

URL:

https://rockmech.whrsm.ac.cn/EN/10.3724/1000-6915.jrme.2024.0522 OR https://rockmech.whrsm.ac.cn/EN/Y2025/V44/I3/543

[1]	JIANG Y J，ZHANG S H，LUAN H J，et al. Numerical modelling of the performance of bolted rough joint subjected to shear load[J]. Geomechanics and Geophysics for Geo-Energy and Geo-Resources，2022，8(5)：140.
[2]	程良奎，张作嵋，杨志银. 岩土加固技术[M]. 北京：地震出版社，1994：22-31.(CHENG Liangkui，ZHANG Zuomei，YANG Zhiyin. Geotechnical reinforcement technology[M]. Beijing：Earthquake Publishing House，1994：22-31.(in Chinese))
[3]	LI C C. Field observations of rock bolts in high stress rock masses[J]. Rock Mechanics and Rock Engineering，2010，43(4)：491-496.
[4]	刘才华，李育宗. 考虑横向抗剪效应的节理岩体全长黏结型锚杆锚固机制研究及进展[J]. 岩石力学与工程学报，2018，37(8)：1 856-1 872.(LIU Caihua，LI Yuzong. Research progress in bolting mechanism and theories of fully grouted bolts in jointed rock masses[J]. Chinese Journal of Rock Mechanics and Engineering，2018，37(8)：1 856-1 872.(in Chinese))
[5]	LI W T，LI X M，MEI Y C，et al. A numerical simulation approach of energy-absorbing anchor bolts for rock engineering[J]. International Journal of Rock Mechanics and Mining Sciences，2022，158：105188.
[6]	ZHAO Z，SUN W，CHEN S，et al. Coupling model of jointed rock mass and rock bolt in offshore LPG underground storage[J]. Energy Science and Engineering，2020，8(5)：1 468-1 483.
[7]	刘泉声，雷广峰，彭星新，等. 白砂岩、大理岩及花岗岩加锚剪切力学特性研究[J]. 岩石力学与工程学报，2018，37(增2)：4 007-4 015.(LIU Quansheng，LEI Guangfeng，PENG Xingxin，et al. Study on shear mechanical properties of sandstone，marble and granite after anchoring[J]. Chinese Journal of Rock Mechanics and Engineering， 2018，37(Supp.2)：4 007-4 015.(in Chinese))
[8]	LIU C H，LI Y Z. Analytical study of the mechanical behavior of fully grouted bolts in bedding rock slopes[J]. Rock Mechanics and Rock Engineering，2017，50：2 413-2 423.
[9]	LI Y，LIU C. Experimental study on the shear behavior of fully grouted bolts[J]. Construction and Building Materials，2019，223：1 123-1 134.
[10]	蒋宇静，张孙豪，栾恒杰，等. 恒定法向刚度边界条件下锚固节理岩体剪切特性试验研究[J]. 岩石力学与工程学报，2021，40(4)：663-675.(JIANG Yujing，ZHANG Sunhao，LUAN Hengjie，et al. Experimental study on shear characteristics of bolted rock joints under constant normal stiffness boundary conditions[J]. Chinese Journal of Rock Mechanics and Engineering，2021，40(4)：663-675.(in Chinese))
[11]	蒋宇静，张孙豪，栾恒杰，等. 锚固方式对岩石节理宏细观剪切特性的影响及其机制研究[J]. 岩石力学与工程学报，2024，43(8)：1 301-1 315.(JIANG Yujing，ZHANG Sunhao，LUAN Hengjie，et al. Study of the effect of anchorage modes on the macro and micro shear characteristics of rock joints and its mechanism[J]. Chinese Journal of Rock Mechanics and Engineering，2024，43(8)：1 301-1 315.(in Chinese))
[12]	WU X，JIANG Y，LI B. Influence of joint roughness on the shear behaviour of fully encapsulated rock bolt[J]. Rock Mechanics and Rock Engineering，2018，51：953-959.
[13]	周友华，胡奉湘，饶云阶，等. 地震应力产生传递与集中机制的研究[J]. 国际地震动态，2004，(11)：8-14.(ZHOU Youhua，HU Fengxiang，RAO Yunjie，et al. Researches on the mechanisms for the transform and concentration of seismic stresses[J]. World Earthquake Dynamics，2004，(11)：8-14.(in Chinese))
[14]	李华东，姜永玲，邓辉. 列车振动荷载作用下某岩质边坡应力应变动力响应分析[J]. 水文地质工程地质，2011，38(3)：42-48.(LI Huadong，JIANG Yongling，DENG Hui. Dynamic response analysis of a rock slope under train vibration load[J]. Hydrogeology and Engineering Geology，2011，38(03)：42-48.(in Chinese))
[15]	吴泽坤，白晓宇，孙淦，等. 多循环荷载下BFRP抗浮锚杆锚固性能现场试验[J]. 岩石力学与工程学报，2024，43(9)：2 314-2 328. (WU Zekun，BAI Xiaoyu，SUN Gan，et al. Field test of anchorage performance of BFRP anti-floating anchor under multiple cyclic loads[J]. Chinese Journal of Rock Mechanics and Engineering，2024，43(9)：2 314-2 328.(in Chinese))
[16]	WU X，ZHENG H，JIANG Y，et al. Effect of cyclic shear loading on shear performance of rock bolt under different joint roughness[J]. Rock Mechanics and Rock Engineering，2023，56(3)：1 969-1 980.
[17]	杨忠平，来云亮，刘树林，等. 频发微震下上覆软弱岩体边坡动力稳定及失稳模式[J]. 岩土工程学报，2019，41(12)：2 297-2 306. (YANG Zhongping，LAI Yunliang，LIU Shulin，et al. Dynamic stability and failure mode of slopes with overlying weak rock mass under frequent micro-seismic actions[J]. Chinese Journal of Geotechnical Engineering，2019，41(12)：2 297-2 306.(in Chinese))
[18]	刘新荣，邓志云，刘永权，等. 峰前循环剪切作用下岩石节理损伤特征与剪切特性试验研究[J]. 岩石力学与工程学报，2018，37(12)：2 664-2 675.(LIU Xinrong，DENG Zhiyun，LIU Yongquan，et al. An experimental study on the cumulative damage and shear properties of rock joints under pre-peak cyclic shear loading[J]. Chinese Journal of Rock Mechanics and Engineering，2018，37(12)：2 664-2 675.(in Chinese))
[19]	HE L，ZHAO Z，LIU L，et al. Asperity degradation characteristics and mechanical behavior of rock joints subjected to pre-peak cyclic loading[J]. Geotechnical and Geological Engineering，2022，40(2)：617-634.
[20]	刘新荣，许彬，周小涵，等. 软弱层峰前循环剪切宏细观累积损伤机制研究[J]. 岩土力学，2021，42(5)：1 291-1 303.(LIU Xinrong，XU Bin，ZHOU Xiaohan，et al. Investigation on macro-meso cumulative damage mechanism of weak layer under pre-peak cyclic shear loading[J]. Rock and Soil Mechanics，2021，42(5)：1 291-1 303.(in Chinese))
[21]	何刘，赵志明，潘岳，等. 连续充填型结构面峰前循环破坏特征及再载强度特性试验研究[J]. 岩石力学与工程学报，2021，40(10)：2 027-2 037.(HE Liu，ZHAO Zhiming，PAN Yue，et al. Experimental study on the damage properties and reloading strength characteristics of continuous in filled rock joints under pre-peak cyclic loading[J]. Chinese Journal of Rock Mechanics and Engineering，2021，40(10)：2 027-2 037.(in Chinese))
[22]	KOU M，LIU X，TANG S，et al. Experimental study of the prepeak cyclic shear mechanical behaviors of artificial rock joints with multiscale asperities[J]. Soil Dynamics and Earthquake Engineering，2019，120：58-74.
[23]	HE M C，WANG Q. Excavation compensation method and key technology for surrounding rock control[J]. Engineering Geology，2022，307：106784.
[24]	LI C C，DOUCET C. Performance of D-bolts under dynamic loading[J]. Rock Mechanics and Rock Engineering，2012，45：193-204.
[25]	WU X，JIANG Y，WANG G，et al. Performance of a new yielding rock bolt under pull and shear loading conditions[J]. Rock Mechanics and Rock Engineering，2019，52：3 401-3 412.
[26]	CAI M，CHAMPAIGNE D. Influence of bolt-grout bonding on MCB conebolt performance[J]. International Journal of Rock Mechanics and Mining Sciences，2012，49：165-175.
[27]	HE M H，WANG Q，WU Q Y. Innovation and future of mining rock mechanics[J]. Journal of Rock Mechanics and Geotechnical Engineering，2021，13(1)：1-21.
[28]	陶志刚，郭爱鹏，何满潮，等. 微观负泊松比锚杆静力学特性及其工程应用研究[J]. 岩土力学，2022，43(3)：808-818.(TAO Zhigang，GUO Aipeng，HE Manchao，et al. Static characteristics and engineering applications of micro negative Poisson?s ratio bolt[J]. Rock and Soil Mechanics，2022，43(3)：808-818.(in Chinese))
[29]	陶志刚，丰于翔，赵易，等. 穿断层隧道NPR锚索支护体系抗震特性振动台试验研究[J]. 岩土力学，2024，45(4)：939-949.(TAO Zhigang，FENG Yuxiang，ZHAO Yi，et al. Shaking table test on anti-seismic characteristics of NPR anchor cable support system for tunnel crossing faults [J]. Rock and Soil Mechanics，2024，45(4)：939-949. (in Chinese))
[30]	陈泓蓉，龙建辉，张吉宁，等. 基于NPR锚索监测的顺层岩质边坡多阶变形规律研究[J]. 岩石力学与工程学报，2024，43(7)：1 763-1 774.(CHEN Hongrong，LONG Jianhui，ZHANG Jining，et al. Research on multistage deformation law of bedding rock slopes based on NPR anchor cable monitoring[J]. Chinese Journal of Rock Mechanics and Engineering，2024，43(7)：1 763-1 774.(in Chinese))
[31]	陶志刚，任树林，何满潮，等. 地下工程微观NPR锚杆钢静力拉伸及锚固抗剪力学特性[J]. 煤炭学报，2022，47(2)：683-694.(TAO Zhigang，REN Shulin，HE Manchao，et al. Static tensile and bolting shear mechanical properties of micro-NPR bolt steel in underground engineering[J]. Journal of China Coal Society，2022，47(2)：683-694. (in Chinese))
[32]	HE M C，REN S，GUO L，et al. Experimental study on influence of host rock strength on shear performance of Micro-NPR bolt steel bolted rock joints[J]. International Journal of Rock Mechanics and Mining Sciences，2022，159：105236.
[33]	HE M C，GUO A，MENG Z，PAN Y，et al. Impact and explosion resistance of NPR anchor cable：Field test and numerical simulation[J]. Underground Space，2023，10：76-90.
[34]	BARTON N. Review of a new shear-strength criterion for rock joints[J]. Engineering Geology，1973，7(4)：287-332.
[35]	杜时贵，黄曼，罗战友，等. 岩石结构面力学原型试验相似材料研究[J]. 岩石力学与工程学报，2010，29(11)：2 263-2 270.(DU Shigui，HUANG Man，LUO Zhanyou，et al. Similar material study of mechanical prototype test of rock structural plane[J]. Chinese Journal of Rock Mechanics and Engineering，2010，29(11)：2 263-2 270.(in Chinese))
[36]	WU X，JIANG Y，LI B. Influence of joint roughness on the shear behaviour of fully encapsulated rock bolt[J]. Rock Mechanics and Rock Engineering，2018，51：953-959.
[37]	WU X，ZHENG H，JIANG Y，et al. Effect of cyclic shear loading on shear performance of rock bolt under different joint roughness[J]. Rock Mechanics and Rock Engineering，2023，56(3)：1 969-1 980.
[38]	邓明科，刘华政，马福栋，等. 聚乙烯醇纤维改性高延性混凝土双面剪切试验及剪切韧性评价方法[J]. 复合材料学报，2020，37(2)：461-471.(DENG Mingke，LIU Huazheng，MA Fudong，et al. Double shear experiment of highly ductile concrete modified by polyvingl alcohol and shear toughness evaluation method[J]. Journal of Composite Materials，2020，37(2)：461-471.(in Chinese))
[39]	孙杰豪，郭保华，田世轩，等. 峰前循环剪切作用下岩石节理剪切力学特性[J]. 岩土力学，2022，43(增2)：52-62.(SUN Jiehao，GUO Baohua，TIAN Shixuan，et al. Shear mechanical properties of rock joints under pre-peakcyclic shearing condition[J]. Rock and Soil Mechanics，2022，43(Supp.2)：52-62.(in Chinese))
[40]	HE M，HU J，CHENG T，et al. Dynamic properties of micro-NPR bolt material and its controlling effect on surrounding rock mass with impact disturbances[J]. Underground Space，2024，15：331-352.
[41]	JALALIFAR H，AZIZ N. Analytical behaviour of bolt-joint intersection under lateral loading conditions[J]. Rock mechanics and rock engineering，2010，43：89-94.
[42]	LI X，AZIZ N，MIRZAGHORBANALI A，et al. Behavior of fiber glass bolts，rock bolts and cable bolts in shear[J]. Rock Mechanics and Rock Engineering，2016，49：2 723-2 735.