岩体结构面三维粗糙度系数表征新方法

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (3402 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要岩体结构面粗糙度系数JRC影响着岩体的变形、破坏以及渗流特性，其数据采集与评价取值问题一直是岩石力学领域的热点和难点。目前研究方法多集中于二维，无法体现JRC的三维特性；即使现有的三维评价方法，也多数仅从几何数据单方面入手，没有考虑JRC的各向异性。鉴于此，提出基于光亮面积百分比BAP的岩体结构面三维粗糙度系数表征新方法。首先，运用三维激光扫描技术，建立岩体结构面三维数字模型；其次，通过模拟虚拟光源，在岩体结构面表面产生光亮与阴影，并生成图片；然后，基于图像分割技术，设置灰度阈值，提取大于灰度阈值的光亮部分面积，并计算岩体结构面的光亮面积百分比；最后，结合R. Tse和D. M. Cruden提出的JRC计算公式，考虑剪切或渗流方向，得出岩体结构面三维粗糙度系数估算公式。以鱼简河水库工程为例，实验结果表明：(1) 在光源照射角度相等的情况下，光亮面积百分比与岩体结构面三维粗糙度系数成正比关系。(2) 通过对比分析，光源照射角度过大(70°～85°)或过小(5°～35°)时，易产生误差，入射角介于35°～70°范围内时为最佳入射角。(3) 基于该工程数据推导出JRC3D与BAP之间的估算公式。通过验证，试样Y10，Y11，Y12根据R. Tse和D. M. Cruden公式所得到的JRC3D分别为16.47，16.81，16.69，根据新估算公式计算的JRC3D分别为17.20，17.40，17.17，具有较好的一致性。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章

关键词 ：岩石力学, 岩体结构面, 粗糙度系数, 三维激光扫描技术, 图像分割技术

Abstract：Joint roughness coefficient(JRC) has influence on the deformation，failure and seepage properties of rock mass discontinuities；and the measurement and estimation of JRC are always focal，but difficult problems in the field of rock mechanics. The majority of the current research methods which have been based on the analysis of two-dimensional(2D) profiles rather than three-dimensional(3D) surface topography lead to erroneous results. On the other hand，the existing 3D evaluation methods only depend on the geometry data，but the anisotropy properties of JRC are ignored. Therefore，a new representation method for 3D JRC based on the brightness area percentage(BAP) was proposed. Firstly，with the help of laser scanning technique，the 3D digital model of rock fracture surfaces was established. Secondly，a light source was simulated；and there would be some brightness and shadows produced on the model surface. In addition，the simulated results were saved as picture format. Thirdly，in order to obtain the value of BAP of each specimen，the image recognition technique was introduced and the brightness area in the picture was identified. Lastly，combination with the results from formula proposed by R. Tse and D. M. Cruden and taking the direction of shear or seepage into account，an empirical formula was found between BAP and 3D joint roughness coefficient(JRC3D). Taking the data of Yujian River Reservoir project for example，the experimental results show that：(1) In the case of equal light source angle，generally，JRC3D are positive proportional to BAP. (2) A comparative analysis of results from different incidence angles was performed；after an extended evaluation，35°–70° was chosen as the most appropriate incidence angle. (3) The evaluation formula for relationship between BAP and JRC3D based on the engineering data of Yujian River Reservoir was derived. The predictions(17.20，17.40，17.17) of JRC3D made with this equation agreed well with the results(16.47，16.81，16.69) obtained in equation proposed by R. Tse and D. M. Cruden.

Key words： rock mechanics rock mass discontinuities joint roughness coefficient(JRC) three-dimensional laser scanning technique image recognition technique

收稿日期: 2012-04-28

引用本文:

葛云峰1，2，唐辉明2，黄磊2，王亮清2，孙淼军2，范怡静2. 岩体结构面三维粗糙度系数表征新方法[J]. 岩石力学与工程学报, 2012, 31(12): 2508-2517.
GE Yunfeng1，2，TANG Huiming2，HUANG Lei2，WANG Liangqing2，SUN Miaojun2，FAN Yijing2. A NEW REPRESENTATION METHOD FOR THREE-DIMENSIONAL JOINT ROUGHNESS COEFFICIENT OF ROCK MASS DISCONTINUITIES. , 2012, 31(12): 2508-2517.

链接本文:

http://www.rockmech.org/CN/Y2012/V31/I12/2508

[2]	赵坚. 岩石节理吻合系数及其对节理特性的影响[J]. 岩石力学与工程学报，1997，16(6)：514-521.(ZHAO Jian. Joint matching coefficient and effects to behavior of rock joint[J]. Chinese Journal of Rock Mechanics and Engineering，1997，16(6)：514-521.(in Chinese))
[9]	HAAS C J. An investigation of the interaction of rock and types of rock bolts for selected loading conditions：final report[M]. Rolla：Rock Mechanics and Explosives Research Center，University of Missouri，1978：250-356. " target="_blank">
[10]	STIMPSON B. A rapid field method for recording joint roughness profiles[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts，1982，19(6)：345-346. " target="_blank">
[11]	杜时贵. 简易纵剖面仪及其在岩体结构面粗糙度系数研究中的应用[J]. 地质科技情报，1992，11(3)：91-95.(DU Shigui. Simple profile instrument and its application to study joint roughness coefficient of rock[J]. Geological Science and Technology Information，1992，11(3)：91-95.(in Chinese))
[34]	BROWN S R，SCHOLZ C H. Broad bandwidth study of the topography of natural rock surfaces[J]. Journal of Geophysics Research，1985，90(B14)：12 575-12 582. " target="_blank">
[37]	HUANG S L，OELFKE S M，SPECK R C. Applicability of fractal characterization and modeling to rock joint profiles[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts，1992，29(12)：89-98. " target="_blank">
[38]	FARDIN N，FENG Q，STEPHANSSON O. Application of a new in situ 3D laser scanner to study the scale effect on the rock joint surface roughness[J]. International Journal of Rock Mechanics and Mining Sciences，2004，41(2)：329-335.
[39]	戴静. 逆向工程数据处理关键技术研究[硕士学位论文][D]. 南京：南京理工大学，2003.(DAI Jing. Study on key technique of data processing in the reverse engineering[M. S. Thesis][D]. Nanjing：Nanjing University of Science and Technology，2003.(in Chinese)) " target="_blank">
[1]	葛云峰，唐辉明，刘晓，等. 岩体结构面直剪实验的剪切面积误差分析[J]. 中国矿业大学学报，2011，40(4)：549-555.(GE Yunfeng，TANG Huiming，LIU Xiao，et al. Error analysis in direct shear rock-mass structural tests[J]. Journal of China University of Mining and Technology，2011，40(4)：549-555.(in Chinese) )
[3]	赵坚. 岩石节理剪切强度的JRC-JMC新模型[J]. 岩石力学与工程学报，1998，17(4)：349-357.(ZHAO Jian. A new JRC-JMC shear strength criterion for rock joint[J]. Chinese Journal of Rock Mechanics and Engineering，1998，17(4)：349-357.( in Chinese))
[4]	夏才初，肖维民，王伟，等. 不同接触状态下节理三维组合形貌的计算方法[J]. 岩石力学与工程学报，2010，29(11)：2 203-2 210. (XIA Caichu，XIAO Weimin，WANG Wei，et al. Calculation method for three-dimensional composite topography of joint under different contact conditions[J]. Chinese Journal of Rock Mechanics and Engineering，2010，29(11)：2 203-2 210.(in Chinese))
[7]	BARTON N，CHOUBEY V. The shear strength of rock joints in theory and practice[J]. Rock Mechanics and Rock Engineering，1977，10(1/2)：1-54. " target="_blank">
[19]	周枝华，杜守继. 岩石节理表面几何特性的三维统计分析[J]. 岩土力学，2005，26(8)：1 227-1 232.(ZHOU Zhihua，DU Shouji. 3D statistic analysis of geometrical properties of a rock joint[J]. Rock and Soil Mechanics，2005，26(8)：1 227-1 232.(in Chinese))
[20]	陈翔，李尤嘉，黄醒春，等. 基于GIS三维统计的膏溶角砾岩断口几何特性研究[J]. 岩石力学与工程学报，2008，27(增2)：3 541-3 546.(CHEN Xiang，LI Youjia，HUANG Xingchun，et al. Study on geometrical properties of fracture appearance in gypsum breccias on 3D GIS statistic[J]. Chinese Journal of Rock Mechanics and Engineering，2008，27(Suup.2)：3 541-3 546.(in Chinese)) " target="_blank">
[5]	KULATILAKE P H S W，UM J，PANDA B B，et al. Development of new peak shear-strength criterion for anisotropic rock joints[J]. Journal of Engineering Mechanics，1999，125(9)：1 010-1 017. " target="_blank">
[8]	SHARMA V M，SAXENA K R. In-situ characterization of rocks[M]. Tokyo：Balkema Publishers，2002：200-310. " target="_blank">
[12]	夏才初，孙宗颀. 节理表面形貌的室内和现场量测及其应用[J]. 勘察科学技术，1994，(4)：27-31.(XIA Caichu，SUN Zongqi. Laboratory and field measurements of the superficial morphology of joints and their applications[J]. Site Investigation Science and Technology，1994，(4)：27-31.(in Chinese)) " target="_blank">
[16]	GRASSELLI G，WIRTHC J，EGGERB P. Quantitative three-dimensional description of a rough surface and parameter evolution with shearing[J]. International Journal of Rock Mechanics and Mining Sciences，2002，39(6)：789-800.
[17]	王金安，谢和平，KWASNIEWSKI M A. 应用激光技术和分形理论测量和描述岩石断裂表面粗糙度[J]. 岩石力学与工程学报，1997，16(4)：354-361.(WANG Jin?an，XIE Heping，KWASNIEWSKI M A. Application of laser technique and fractal theory to the measurement and characterization on roughness of rock fracture surfaces[J]. Chinese Journal of Rock Mechanics and Engineering，1997，16(4)：354-361. (in Chinese))
[22]	JIANG Y J，LI B，TANABASHI Y. Estimating the relation between surface roughness and mechanical properties of rock joints[J]. International Journal of Rock Mechanics and Mining Sciences，2006，43(6)：837-846. " target="_blank">
[23]	MAERZ N H，FRANKLIN J A，BENNETT C P. Joint roughness measurement using shadow profilometry[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts，1990，27(5)：329-343. " target="_blank">
[24]	王卫星，杨记明. 一种基于图像处理的岩石裂隙粗糙度几何信息算法[J]. 重庆邮电大学学报：自然科学版，2010，22(4)：454-457. (WANG Weixing，YANG Jiming. A geometric information on roughness of rock fractures based on image processing[J]. Journal of Chongqing University of Posts and Telecommunications：Natural Science，2010，22(4)：454-457.(in Chinese))
[26]	BARTON N，BANDIS S. Effects of block size on the shear behavior of jointed rock[C]// Proceedings of the 23rd U. S. Symposium on Rock Mechanics. Berkeley，USA：[s. n.]，1982：739-760. " target="_blank">
[27]	WU T H，ALI E M. Statistical representation of joint roughness[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts，1978，15(5)：259-262. " target="_blank">
[6]	ANDRADE P S，SARAIVA A A. Estimating the joint roughness coefficient of discontinuities found in metamorphic rocks[J]. Bulletin of Engineering Geology and the Environment，2008，67(3)：425-434.
[28]	TSE R，CRUDEN D M. Estimating joint roughness coefficients[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts，1979，16(5)：303-307. " target="_blank">
[31]	张鹏，李宁，陈新民. 一种新的裂隙三维表面粗糙度表征方法[J]. 岩石力学与工程学报，2009，28(增2)：3 477-3 483.(ZHANG Peng， LI Ning，CHEN Xinmin. A new representation method for three- dimensional surface roughness of rock fracture[J]. Chinese Journal of Rock Mechanics and Engineering，2009，28(Supp.2)：3 477-3 483. (in Chinese))
[35]	谢和平，PARISEAU W G. 岩石节理粗糙系数(JRC)的分形估计[J]. 中国科学：B辑，1994，24(5)：524-530.(XIE Heping，PARISEAU W G. Fractural estimation of joint roughness using fractal dimension[J]. Science in China：Series B，1994，24(5)：524-530.(in Chinese)) " target="_blank">
[40]	王运琼，游志胜，刘直芳. 基于空间特征的汽车阴影分割方法[J]. 光电工程，2003，30(2)：64-67.(WANG Yunqiong，YOU Zhisheng， LIU Zhifang. Vehicle shadow segmentation method based on spatial characteristics[J]. Opto-Electronic Engineering，2003，30(2)：64-67.(in Chinese))
[43]	陈晓东，陈建裕，毛志华，等. 基于MPHD算法的高分辨率遥感影像对海洋上空的云及其阴影的识别与匹配[J]. 海洋学研究，2009， 27(2)：51-57.(CHEN Xiaodong，CHEN Jianyu，MAO Zhihua，et al. Recognition and matching of clouds and shadows on ocean area by high resolution satellite image based on MPHD algorithm[J]. Journal of Marine Sciences，2009，27(2)：51-57.(in Chinese))
[45]	梅雪良，张祖勋，张剑清. 基于约束满足网络的建筑物阴影结构提取[J]. 武汉测绘科技大学学报，1996，21(3)：265-268.(MEI Xueliang，ZHANG Zuxun，ZHANG Jianqing. Constraint satisfaction network(CSN)-based extraction of buildings? shadow structures[J]. Journal of Wuhan Technical University of Surveying and Mapping，1996，21(3)：265-268.(in Chinese))
[46]	于庆磊，唐春安，唐世斌. 基于数字图像的岩石非均匀性表征技术及初步应用[J]. 岩石力学与工程学报，2007，26(3)：551-559. (YU Qinglei，TANG Chun?an，TANG Shibin. Digital image based characterization method of rock?s heterogeneity and its primary application[J]. Chinese Journal of Rock Mechanics and Engineering，2007，26(3)：551-559.(in Chinese))
[13]	DEVELI K，BABADAGLIT，COMLEKCI C. A new computer-controlled surface-scanning device for measurement of fracture surface roughness[J]. Computers and Geosciences，2001，27(3)：265-277.
[14]	吉锋，石豫川，冯文凯. 一种新型的结构面起伏形态测量工具——接触打孔器的研制[C]// 黄润秋，许强编. 第三届全国岩土与工程学术大会论文集. 成都：四川科学技术出版社，2009：651-653. (JI Feng，SHI Yuchuan，FENG Wenkai. A new measurement of rock joints surface—contact punching device[C]// HUANG Runqiu，XU Qiang ed. Proceedings of the 3rd Conference of Geo-engineering，China. Chengdu：Sichuan Publishing House of Science and Technology，2009：651-653.(in Chinese)) " target="_blank">
[15]	尹红梅，张宜虎，孔祥辉. 结构面剪切强度参数三维分形估算[J]. 水文地质工程地质，2011，38(4)：58-62.(YIN Hongmei，ZHANG Yihu，KONG Xianghui. Estimation of joint shear strength based on fractal method[J]. Hydrogeology and Engineering Geology，2011，38(4)：58-62.(in Chinese))
[18]	李庆松，杜守继. 经历剪切变形历史的岩石节理表面粗糙特性分析[J]. 岩土力学，2004，25(6)：850-855.(LI Qingsong，DU Shouji. Surface roughness analysis of rock joints under different shear deformation histories[J]. Rock and Soil Mechanics，2004，25(6)：850-855.(in Chinese))
[21]	KULATILAKE P H S W，BALASINGAM P，PARK J Y，et al. Natural rock joint roughness quantification through fractal techniques[J]. Geotechnical and Geological Engineering，2006，24(5)：1 181-1 202. " target="_blank">
[25]	KHOSHELHAM K，ALTUNDAG D，NGAN-TILLARD D，et al. Influence of range measurement noise on roughness characterization of rock surfaces using terrestrial laser scanning[J]. International Journal of Rock Mechanics and Mining Sciences，2011，48(8)：1 215-1 223. " target="_blank">
[29]	BELEM T，HOMAND-ETIENNE F，SOULEY M. Quantitative parameters for rock joint surface roughness[J]. Rock Mechanics and Rock Engineering，2000，33(4)：217-242.
[30]	HERDA H H W. An algorithmic 3D rock roughness measure using local depth measurement clusters[J]. Rock Mechanics and Rock Engineering，2006，39(2)：147-158.
[32]	吴月秀，刘泉声，刘小燕. 岩体节理粗糙度系数与统计参数的相关关系研究[J]. 岩石力学与工程学报，2011，30(增1)：2 593-2 598. (WU Yuexiu，LIU Quansheng，LIU Xiaoyan. Study of relationship between joint roughness coefficient and statistical parameters[J]. Chinese Journal of Rock Mechanics and Engineering，2011，30(Supp.1)：2 593-2 598.(in Chinese))
[33]	RAFEK A G，GOH T L. Correlation of joint roughness coefficient (JRC) and peak friction angles of discontinuities of Malaysian schists[J]. Earth Science Research，2012，1(1)：57-63. " target="_blank">
[36]	MALINVERNO A. A simple method to estimate the fractal dimension of a self affine series[J]. Geophysics Research Letters，1990，17(11)：1 953-1 956. " target="_blank">
[41]	LEONE A，DISTANTE C. Shadow detection for moving objects based on texture analysis[J]. Pattern Recognition，2007，40(4)：1 222-1 233. " target="_blank">
[42]	JOHANSSON B，WIKLUND J，FORSSEN P E，et al. Combining shadow detection and simulation for estimation of vehicle size and position[J]. Pattern Recognition Letters，2009，30(8)：751-759.
[47]	徐海清. 贵州省鱼简河水库坝基岩体力学参数研究[硕士学位论文][D]. 武汉：中国地质大学，2004.(XU Haiqing. Study on mechanical parameters of rock mass of dam foundation of Yujianhe reservoir in Guizhou Province[M. S. Thesis][D]. Wuhan：China University of Geosciences，2004.(in Chinese)) " target="_blank">
[44]	郭雷，吴成柯，陆心如. 矽肺小阴影的计算机识别[J]. 西北电讯工程学院学报，1987，14(1)：38-44.(GUO Lei，WU Chengke，LU Xinru. A computer recognition of small rounded pneumoconiosis opacities in chest X-rays[J]. Journal of Northwest Telecommunication Engineering Institute，1987，14(1)：38-44.(in Chinese))
[48]	杜时贵. 岩体结构面抗剪强度经验估算[M]. 北京：地震出版社，2005：57-60.(DU Shigui. Empirical estimation on the shear strength of rock mass discontinuity[M]. Beijing：Earthquake Press，2005：57-60. (in Chinese)) " target="_blank">