基于响应面法的破碎围岩条件下采场结构参数优化研究

doi:10.13722/j.cnki.jrme.2016.0715

摘要
图/表
参考文献(28)
相关文章 (15)

全文: PDF (1381 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要

为了获得最优的采场结构参数，综合考虑矿山的安全性和经济性，提出响应面的方法，采用中心复合试验研究采场高度、矿柱直径、矿柱排距和矿柱间距对破碎围岩条件下矿柱最大拉应力、最大压应力和矿石回收率的影响规律。通过有限元的计算结果建立矿柱最大拉应力、最大压应力和矿石回收率响应面回归模型，最后采用基于整体满意度准则的非线性多目标优化技术对采场结构参数进行优化。结果表明：整体满意度随采场高度的增加而降低，随矿柱直径、矿柱间距和矿柱排距的增大，呈现出先增大后减少的趋势，白牛厂矿最优的采场高度为3.5 m，矿柱直径为3.5 m，矿柱间距为3 m，矿柱排距为5 m。该方法科学合理，为白牛厂矿破碎围岩条件下安全、经济、高效回采矿石提供了技术保障。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	陈顺满1
	2
	吴爱祥1
	2
	王贻明1
	2
	陈勋1
	2

关键词 ：岩石力学, 采场结构参数, 响应面法, 中心复合试验, 多目标优化

Abstract：To obtain the optimal stope structure parameters，when the mine safety and economy were considered together，the response surface method was put forward，and the central composite design experiments were performed to investigate the effect of stope height，pillar diameter，pillar spacing and pillar array pitch in broken rock conditions on the maximum tensile stress，maximum compressive stress and ore recovery rate. The response surface regression models of the maximum tensile stress，maximum compressive stress and the ore recovery rate were established by the results of finite element model，then the stope structure parameters were optimized by the method of nonlinear multi-objective technology based on the overall desirability criteria. It is found that the overall desirability of stope reduced along with the increase of mining height，and it presents a trend of increase，then decreases with the increase of pillar diameter，pillar spacing and pillar width. The optimal mining height is 3.5 m，the pillar diameter is 3.5 m，the pillar spacing is 3 m and the pillar array pitch is 5 m. This method is scientific，reasonable，and provides the technical support for Bainiuchang mine?s safety，economy and efficient exploitation in broken rock conditions.

Key words： rock mechanics stope structure parameters response surface method central composite design multi-objective optimization

引用本文:

陈顺满1，2，吴爱祥1，2，王贻明1，2，陈勋1，2. 基于响应面法的破碎围岩条件下采场结构参数优化研究[J]. 岩石力学与工程学报, 2017, 36(S1): 3499-3508.
CHEN Shunman1，2，WU Aixiang1，2，WANG Yiming1，2，CHEN Xun1，2. Optimization research on stope structure parameters in broken rock conditions based on the response surface method. , 2017, 36(S1): 3499-3508.

链接本文:

https://rockmech.whrsm.ac.cn/CN/10.13722/j.cnki.jrme.2016.0715 或 https://rockmech.whrsm.ac.cn/CN/Y2017/V36/IS1/3499

[1]	韩斌，吴爱祥，刘同有，等. 金川二矿区多中段机械化盘区回采顺序的数值模拟优化研究[J]. 矿冶工程，2004，24(2)：4-7.(HAN Bin，WU Aixiang，LIU Tongyou，et al. Optimization of mining sequences of multi-level mechanized panels of Jinchuan¢s No.2 mining area through numerical method[J]. Mining and Metallurgical Engineering，2004，24(2)：4-7.(in Chinese))
[2]	罗周全，管佳林，冯富康，等. 盘区隔离矿柱采场结构参数数值优化[J]. 采矿与安全工程学报，2012，29(2)：261-264.(LUO Zhouquan，GUAN Jialin，FENG Fukang，et al. Stope structural parameters of panel isolation pillar numerical optimization[J]. Journal of Mining and Safety Engineering，2012，29(2)：261-264.(in Chinese))
[3]	韩志型，王宁. 急倾斜厚矿体无间柱上向水平分层充填法采场结构参数的研究[J]. 岩土力学，2007，28(2)：367-370.(HAN Zhixing，WANG Ning. Analysis of structural parameters for dipping at high angle and thick orebody with upward horizontal slicing and filling non-pillar continuous mining[J]. Rock and Soil Mechanics，2007，28(2)：367-370.(in Chinese))
[4]	杨清平，滕丙娟，胡文达，等. 谦比西铜矿西矿体采场结构参数优化[J]. 金属矿山，2012，41(5)：1-4.(YANG Qingping，TENG Bingjuan，HU Wenda，et al. Stope structure parameters optimization of west orebody in Chambishi copper mine[J]. Metal Mine，2012，41(5)：1-4.(in Chinese))
[5]	朱志彬，刘成平. 厚大矿体回采顺序和采场结构参数优化[J]. 中国矿山工程，2008，37(4)：20-24.(ZHU Zhibin，LIU Chengping. Stoping sequence and optimum of structural parameter of thick orebody[J]. China Mine Engineering，2008，37(4)：20-24.(in Chinese))
[6]	周科平，苟国刚，罗佳，等. 基于Mathew与数值模拟法的采场结构参数优化及稳定性研究[J]. 科技导报，2013，31(30)：34-38. (ZHOU Keping，GOU Guogang，LUO Jia，et al. Optimization of structural parameters and stability of stope based on Mathew method and numerical simulation method[J]. Science and Technology Review，2013，31(30)：34-38.(in Chinese))
[7]	马生徽，王文杰，邓金灿，等. 基于数值模拟的高峰矿深部采场结构参数优化研究[J]. 中国矿业，2013，(8)：98-102.(MA Shenghui，WANG Wenjie，DENG Jincan，et al. Study on optimization of structural parameters for deep stope in Gaofeng mine based on numerical simulation[J]. Chinese Mining Magazine，2013，(8)：98-102.(in Chinese))
[8]	CHENG Y M，WANG J A，XIE G X，et al. Three dimensional analysis of coal barrier pillars in tailgate area adjacent to the fully mechanized top caving mining face[J]. International Journal of Rock Mechanics and Mining Sciences，2010，47(8)：1 372-1 383.
[9]	王新民，李洁慧，张钦礼，等. 基于FAHP的采场结构参数优化研究[J]. 中国矿业大学学报，2010，39(2)：163-168.(WANG Xinmin，LI Jiehui，ZHANG Qinli，et al. Optimization mining stope structure parameters using a FAHP[J]. Journal of China University of Mining and Technology，2010，39(2)：163-168.(in Chinese))
[10]	张国联，宋健，刘兴国. 张家洼铁矿沿脉无底柱分段崩落法结构参数试验研究[J]. 中国矿业，2005，14(9)：45-48.(ZHANG Guolian，SONG Jian，LIU Xingguo. Experimental research on structure parameter of non-pillar sublevel caving along vein of zhangjiawa iron mine[J]. Chinese Mining Magazine，2005，14(9)：45-48.(in Chinese))
[11]	SONG W D，WANG D X，TANG Y N. Study on sublevel open stoping with subsequent backfilling mining method stope parameters optimization[J]. Advanced Materials Research，2011，250-253(1/4)：1 567-1 571.
[12]	刘钦，刘志祥，刘爱华，等. 金矿采场结构参数混沌优化[J].采矿与安全工程学报，2010，27(4)：548-552.(LIU Qin，LIU Zhixiang，LIU Aihua，et al. Chaotic optimization of structural parameters in gold mining field[J]. Journal of Mining and Safety Engineering，2010，27(4)：548-552.(in Chinese))
[13]	彭康，李夕兵，彭述权，等. 基于响应面法的海下框架式采场结构优化选择[J]. 中南大学学报：自然科学版，2011，42(8)：2 417-2 422. (PENG Kang，LI Xibin，PENG Shuquan，et al. Optimization of frame stope structure parameters based on response surface method in under-sea mining[J]. Journal of Central South University：Science and Technology，2011，42(8)：2 417-2 422.(in Chinese))
[14]	GUO Y，HOU K，LI W. Numerical optimization of stope structural parameters of complex inclined thin orebody in Mengnuo lead-zinc mine[J]. Electronic Journal of Geotechnical Engineering，2014，19(1)：9 479-9 490.
[15]	BAI X，MARCOTTE D，SIMON R . Underground stope optimization with network flow method[J]. Computers and Geoscience，2013，52(1)：361-371.
[16]	SANDANAYAKE D S S，TOPAL E，ASAD M W A. Designing an optimal stope layout for underground mining based on a heuristic algorithm[J]. International Journal of Mining Science and Technology，2015，25(5)：767-772.
[17]	陈建康，朱殿芳，赵文谦，等. 基于响应面法的地下洞室结构可靠度分析[J]. 岩石力学与工程学报，2005，24(2)：351-356.(CHEN Jiankang，ZHU Dianfang，ZHAO Wenqian，et al. Structure reliability analysis of underground cavern based on response surface of method[J]. Chinese Journal of Rock Mechanics and Engineering，2005，24(2)：351-356.(in Chinese))
[18]	赵国彦，马举弓，彭康，等. 基于响应面法的高寒矿山充填配比优化[J]. 北京科技大学学报，2013，35(5)：559-565.(ZHAO Guoyan，MA Jugong，PENG Kang，et al. Mix ratio optimization of alpine mine backfill based on the response surface method[J]. Journal of University of Science and Technology Beijing，2013，35(5)：559-565.(in Chinese))
[19]	苏永华，方祖烈，高谦. 用响应面方法分析特殊地下岩体空间的可靠性[J]. 岩石力学与工程学报，2000，19(1)：55-58.(SU Yonghua，FANG Zulie，GAO Qian. Reliability analysis on special underground rockmass space by response surface method[J]. Chinese Journal of Rock Mechanics and Engineering，2000，19(1)：55-58.(in Chinese))
[20]	GUO Q，PEI L，ZHOU Z，et al. Response surface and genetic method of deformation back analysis for high core rockfill dams[J]. Computers and Geotechnics，2016，74(3)：132-140.
[21]	姚高辉，吴爱祥，王贻明，等. 破碎围岩条件下采场留存矿柱稳定性分析[J]. 北京科技大学学报，2011，33(4)：400-405.(YAO Gaohui，WU Aixiang，WANG Yiming，et al. Stability analysis of stope retention pillars in broken rock conditions[J]. Journal of University of Science and Technology Beijing，2011，33(4)：400-405.(in Chinese))
[22]	张广超，何富连. 大断面强采动综放煤巷顶板非对称破坏机制与控制对策[J]. 岩石力学与工程学报，2016，35(4)：806-818.(ZHANG Guangchao，HE Fulian. Asymmetric failure and control measures of large cross-section entry roof with strong mining disturbance and fully-mechanized caving mining[J]. Chinese Journal of Rock Mechanics and Engineering，2016，35(4)：806-818.(in Chinese))
[23]	胡盛明，胡修文. 基于量化的GSI系统和Hoek-Brown准则的岩体力学参数的估计[J]. 岩土力学，2011，32(3)：861-866.(HU Shengming，HU Xiuwen. Estimation of rock mass parameters based on quantitative GSI system and Hoek-Brown criterion[J]. Rock and Soil Mechanics，2011，32(3)：861-866.(in Chinese))
[24]	FALL M，BENZAAZOUA M，SAA E G. Mix proportioning of underground cemented tailings backfill[J]. Tunnelling and Underground Space Technology，2008，23(1)：80-90.
[25]	陈希孺. 概率论与数理统计[M]. 合肥：中国科学技术大学出版社，2007.(CHEN Xiru. Probability theory and mathematical statistics[M]. Hefei：Press of University of Science and Technology of China，2007. (in Chinese))
[26]	DERRINGER G. Simultaneous optimization of several response variable[J]. Journal of Quality Technology，1980，12(4)：214-219.
[27]	SUBASI A，SAHIN B，KAYMAZ I. Multi-objective optimization of a honeycomb heat sink using response surface method[J]. International Journal of Heat and Mass Transfer，2016，101(5)：295-302.
[28]	GOSWAMI S，GHOSH S，CHAKRABORTY S. Reliability analysis of structures by iterative improved response surface method[J]. Structural Safety，2016，60(2)：56-66.