峰前循环剪切作用下岩石节理损伤特征与剪切特性试验研究

doi:10.13722/j.cnki.jrme.2018.0526

Abstract
Figure/Table
References (0)
Related Citation (15)

Download: PDF (912 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract To investigate the cumulative damage characteristics of rock joints under different failure modes，the original rock samples with second-order asperities were obtained by adopting water knife cutting processing method，and the direct shear test was carried out under pre-peak cyclic loading conditions. The influence of the cyclic loading times，the loading rate and the loading amplitude on shear properties of rock joints were analyzed. Results show that the cumulative damage of a rock joint with climbing failure mode is characterized by the abrasion of second-order asperities，that the cumulative damage of a rock joint with cutting failure mode is characterized by the crack initiation and crack coalescence of the first-order asperity，and that，under the climbing-cutting failure mode，the cumulative damage of a rock joint has the damage features of the climbing failure and the cutting failure modes. With increasing loading cycles，the peak shear strength of the rock joint presents a trend of increasing at first and decreasing subsequently while the residual shear strength of the rock joint almost keeps stable. When the loading rate or the loading amplitude increases，the deterioration speed of the peak shear strength of the rock joint increases and hence，the peak shear strength of the rock joint decreases. The effect of pre-peak cyclic loading on the rock joint can be attributed to contact effect and damage effect，and the evolution of the two effects is the root cause for the peak shear strength of the rock joint increasing at first and decreasing subsequently during direct shear test under pre-peak cyclic loading.

Key words： rock mechanics pre-peak cyclic shear loading rock joints failure modes damage characteristics shear properties

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	LIU Xinrong1
	2
	DENG Zhiyun1
	2
	LIU Yongquan1
	2
	3
	LIU Shulin1
	2
	LU Yuming4
	HAN Yafeng1
	2

Cite this article:

LIU Xinrong1,2,DENG Zhiyun1, et al. An experimental study on the cumulative damage and shear properties of rock joints under pre-peak cyclic shear loading[J]. , 2018, 37(12): 2664-2675.

URL:

http://www.rockmech.org/EN/10.13722/j.cnki.jrme.2018.0526 OR http://www.rockmech.org/EN/Y2018/V37/I12/2664

[1]	王姣，李长冬，雍睿，等. 三峡库区侏罗系不同类型结构面抗剪强度对比[J]. 煤田地质与勘探，2014，42(5)：61-66.(WANG Jiao，LI Changdong，YONG Rui，et al. Comparison study on shear strength parameters of Jurassic different rock discontinuities in Three Gorges Reservoir region[J]. Coal Geology and Exploration，2014，42(5)：61-66.(in Chinese))
[3]	刘博，李海波，刘亚群. 循环剪切荷载作用下岩石节理变形特性试验研究[J]. 岩土力学，2013，34(9)：2 475-2 481.(LIU Bo，LI Haibo，LIU Yaqun. Experimental study of deformation behavior of rock joints under cyclic shear loading[J]. Rock and Soil Mechanics，2013，34(9)：2 475-2 481.(in Chinese))
[5]	LEE H S，PARK Y J，CHO T F，et al. Influence of asperity degradation on the mechanical behavior of rough rock joints under cyclic shear loading[J]. International Journal of Rock Mechanics and Mining Sciences，2001，38(7)：967-980.
[8]	袁小清，刘红岩，刘京平. 冻融荷载耦合作用下节理岩体损伤本构模型[J]. 岩石力学与工程学报，2015，34(8)：1 602-1 611.(YUAN Xiaoqing，LIU Hongyan，LIU Jingping. A damaging model of jointed rock under coupled action of freezing and thawing[J]. Chinese Journal of Rock Mechanics and Engineering，2015，34(8)：1 602-1 611.(in Chinese))
[9]	朱小明，李海波，刘博. 循环剪切荷载作用下含二阶起伏体模拟岩石节理力学特性研究[J]. 岩土力学，2014，35(2)：371-379.(ZHU Xiaoming，LI Haibo，LIU Bo. Study of mechanical characteristics of simulated rock joints with second-order asperity under cyclic shear loading[J]. Rock and Soil Mechanics，2014，35(2)：371-379.(in Chinese))
[6]	JAFARI M K，HOSSEINI K A，PELLET F，et al. Evaluation of shear strength of rock joints subjected to cyclic loading[J]. Soil Dynamics and Earthquake Engineering，2003，23(7)：619-630.
[11]	BARLA G，BARLA M，MARTINOTTI M E. Development of a new direct shear testing apparatus[J]. Rock Mechanics and Rock Engineering，2010，43(1)：117-122.
[13]	YANG Z Y，DI C C，YEN K C. The effect of asperity order on the roughness of rock joints[J]. International Journal of Rock Mechanics and Mining Sciences，2001，38(5)：745-752.
[15]	朱小明，李海波，刘博，等. 含一阶和二阶起伏体节理剪切强度的试验研究[J]. 岩石力学与工程学报，2011，30(9)：1 810-1 818. (ZHU Xiaoming，LI Haibo，LIU Bo，et al. Experimental study of shear strength of joints with first-order and second-order asperities[J]. Chinese Journal of Rock Mechanics and Engineering，2011，30(9)：1 810-1 818.(in Chinese))
[16]	朱小明，李海波，刘博，等. 含二阶起伏体的模拟岩体节理试样剪切特性试验研究[J]. 岩土力学，2012，33(2)：354-360.(ZHU Xiaoming，LI Haibo，LIU Bo，et al. Experimental study of shear characteristics by simulating rock mass joints sample with second-order asperities[J]. Rock and Soil Mechanics，2012，33(2)：354-360.(in Chinese))
[19]	李海波，蒋会军，赵坚，等. 动荷载作用下岩体工程安全的几个问题[J]. 岩石力学与工程学报，2003，22(11)：1 887-1 891.(LI Haibo，JIANG Huijun，ZHAO Jian，et al. Some problems about safty analysis of rock engineering under dynamic load[J]. Chinese Journal of Rock Mechanics and Engineering，2003，22(11)：1 887-1 891.(in Chinese))
[7]	刘博，李海波，刘亚群，等. 循环荷载作用下节理凸起体概化破坏模型及剪切强度计算分析[J]. 岩石力学与工程学报，2013，32(增2)：3 000-3 008.(LIU Bo，LI Haibo，LIU Yaqun，et al. Generalized damage model for asperity and shear strength calculation of joints under cyclic shear loading[J]. Chinese Journal of Rock Mechanics and Engineering，2013，32(Supp. 2)：3 000-3 008.(in Chinese))
[2]	周友华，胡奉湘，饶云阶，等. 地震应力产生传递与集中机制的研究[J]. 国际地震动态，2004，34(11)：8-14.(ZHOU Youhua，HU Fengxiang，RAO Yunjie，et al. Researches on the mechanisms for the transform and concentration of seismic stresses[J]. Recent Developments in World Seismology，2004，34(11)：8-14.(in Chinese))
[4]	HOMAND F，BELEM T，SOULEY M. Friction and degradation of rock joint surfaces under shear loads[J]. International Journal for Numerical and Analytical Methods in Geomechanics，2001，25(10)：973-999.
[10]	JIANG Y，LI B，TANABASHI Y. Estimating the relation between surface roughness and mechanical properties of rock joints[J]. International Journal of Rock Mechanics and Mining Sciences，2006，43(6)：837-846.
[12]	HUANG X，HAIMSON B C，PLESHA M E，et al. An investigation of the mechanics of rock joints-Part I. Laboratory investigation[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts，1993，30(3)：257-269.
[14]	夏才初，孙宗颀. 工程岩体节理力学[M]. 上海：同济大学出版社，2002：18-29.(XIA CaiChu，Sun ZongQi. Jointed rock mechanics of engineering rock[M]. Shanghai：Tongji University Press，2002：18-29. (in Chinese))
[17]	陈德基，汪雍熙，曾新平. 三峡工程水库诱发地震问题研究[J]. 岩石力学与工程学报，2008，27(8)：1 513-1 524.(CHEN Deji，WANG Yongxi，ZENG Xinping. a study of reservoir-induced earthquake of three gorges project[J]. Chinese Journal of Rock Mechanics and Engineering，2008，27(8)：1 513-1 524.(in Chinese))
[18]	马文涛，徐长朋，李海鸥，等. 长江三峡水库诱发地震加密观测及地震成因初步分析[J]. 地震地质，2010，32(4)：552-563.(MA Wentao，XU Changpeng，LI Haiou，et al. Intensive observation of reservoir-induced earthquake and preliminary analysis on the causes of earthquakes in three gorges reservoir[J]. Seismology and Geology，2010，32(4)：552-563.(in Chinese))
[20]	FERRERO A M，MIGLIAZZA M，TEBALDI G. Development of a new experimental apparatus for the study of the mechanical behaviour of a rock discontinuity under monotonic and cyclic loads[J]. Rock Mechanics and Rock Engineering，2010，43(6)：685-695.
[22]	中华人民共和国国家标准编写组. GB/T 50266—2013工程岩体试验方法标准[S]. 北京：中国计划出版社，2013：25-26.(The National Standards Compilation Group of people?s Republic of China GB/T 50266—2013 Standard for test methods of engineering rock mass[S]. Beijing：China Planning Press，2013：25-26.(in Chinese))
[21]	TSUBOTA Y，KUNISHI T，IWAKOKE Y，et al. Fundamental studies on dynamic properties of rock joint under cyclic loading using mortar and Ryoke gneiss[C]// Proceddings of the 1st International Conference on Rock Dynamics and Applications(RocDyn). [S. l.]：[s. n.]，2013：225-232.
[23]	黄达，黄润秋，雷鹏. 贯通型锯齿状岩体结构面剪切变形及强度特征[J]. 煤炭学报，2014，39(7)：1 229-1 237.(HUANG Da，HUANG Runqiu，LEI Peng. Shear deformation and strength of through-going saw-tooth rock discontinuity[J]. Journal of China Coal Society，2014，39(7)：1 229-1 237.(in Chinese))