基于标准结构面粗糙度曲线的JRC量化算法

doi:10.13722/j.cnki.jrme.2020.0960

Abstract
Figure/Table
References (0)
Related Citation (15)

Download: PDF (56874 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract The roughness of joints in rock mass is very important for the calculation of the shear strength. However，the determination of JRC(joint roughness coefficient) based on the 10 standard curves established by Barton is often subjective and uncertain，so it is important theoretical significance and practical application values to do further study about this issue. In this paper，all the standard joint roughness curves by Barton are quantized. The length of the datum line L0 is selected as 10 cm and the contour length L of each curve is measured. The functional relationship between the section length ratio of the contour length to the datum line length L/L0 and JRC can be fitted. Based on the ellipse definition and the sine function method，the curves are redistributed according to their contour lengths，and the maximum undulation Ry1 and Ry2 under two extreme distribution states are obtained. Making the maximum undulations correspond to the upper and lower limits of JRC，then，the functional relationship between Ry and JRC can be fitted. Finally，by bivariate fitting of the above two functional relationships，the functional relationship between JRC with L/L0 and Ry is obtained with a fit goodness of 99.24%. Taking the discontinuities of the slopes in Heihe reservoir area and Zhen¢an County of Xi¢an city as the cases，comparison between the developed approach with the classical JRC calculation method is performed. It is found that the calculation results are similar while the change trend of the JRC value calculated by the proposed function is more stable than the classical method，verifying the feasibility of the developed method.

Key words： rock mechanics rock mass discontinuity joint roughness coefficient(JRC) quantitative algorithm

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	TANG Qinghao1
	ZHANG Changliang1
	2
	ZHANG Guowei3
	JIAO Zhenli1

Cite this article:

TANG Qinghao1,ZHANG Changliang1,2, et al. Quantization algorithm of joint roughness coefficient based on standard joint roughness curves[J]. , 2021, 40(7): 1402-1411.

URL:

http://rockmech.whrsm.ac.cn/EN/10.13722/j.cnki.jrme.2020.0960 OR http://rockmech.whrsm.ac.cn/EN/Y2021/V40/I7/1402

[2]	BARTON N. Review of a new shear-strength criterion for rock joints[J]. Barton Nicholas，1973，7(4)：287-332.
[5]	杜时贵，陈禹，樊良本. JRC修正直边法的数学表达[J]. 工程地质学报，1996，4(2)：36-43.(DU Shigui，CHEN Yu，FAN Liangben. Mathematical expression of JRC modified straight edge[J]. Journal of Engineering Geology，1996，4(2)：36-43.(in Chinese))
[15]	EL-SOUDANI S M. Profilometric analysis of fractures[J]. Metallography，1978，11(3)：247-336.
[3]	BARTON N，CHOUBEY V. The shear strength of rock joints in theory and practice[J]. Rock Mechanics and Rock Engineering，1977，10(1)：1-54.
[7]	唐志成，宋英龙. 一种描述结构面剖面线粗糙度的新方法[J]. 工程地质学报，2011，19(2)：250-253.(TANG Zhicheng，SONG Yinglong. New method for assessing rock discontinuity roughness on linear profiles[J]. Journal of Engineering Geology，2011，19(2)：250-253.(in Chinese))
[9]	李化，黄润秋. 岩石结构面粗糙度系数JRC定量确定方法研究[J]. 岩石力学与工程学报，2014，33(增2)：3 489-3 497.(LI Hua，HUANG Runqiu. Method of quantitative determination of joint roughness coefficient[J]. Chinese Journal of Rock Mechanics and Engineering，2014，33(Supp.2)：3 489-3 497.(in Chinese))
[14]	BARTON N. Modelling rockjointbehaviorfromin-suitblocktest：implications for nuclear waste repository design[R]. Columbus：[s. n.]，1982：381-385.
[1]	WU J M，MABTAB A，XU S L. Estimation the Barton equation for the shear strength of rock joints[J]. Journal of Engineering Geology，2001，9(4)：349-352.
[4]	BARTON N，BANDIS S. Effects of block size on the shear behaviour of jointed rock[C]// Proceedings of the 23rd U.S. Symposium on Rock Mechanics. Berkeley：[s. n.]，1982：739-760.
[6]	LEE Y H，CARR J R，BARR D J，et al. The fractal dimension as ameasure of the roughness of rock discontinuity profiles[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts，1990，27(6)：453-464.
[8]	葛云峰，唐辉明，黄磊，等. 岩体结构面三维粗糙度系数表征新方法[J]. 岩石力学与工程学报，2012，31(12)：2 508-2 517.(GE Yunfeng，TANG Huiming，HUANG Lei，et al. A new representation method for three-dimensional joint roughness coefficient of rock mass discontinuities[J]. Chinese Journal of Rock Mechanics and Engineering，2012，31(12)：2 508-2 517.(in Chinese))
[10]	杜时贵，郭霄. 岩体结构面粗糙度系数JRC的研究现状[J]. 水文地质工程地质，2003，(增1)：30-33.(DU Shigui，GUO Xiao. Recent development of the joint roughness coefficient(JRC)[J]. Hydrogeology and Engineering Geology，2003，(Supp.1)：30-33.(in Chinese))
[12]	BARTON N，BANDIS S. Some effects of scale on the shear strength of joints[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts，1980，17(1)：69-73.
[17]	王岐. 用伸长率R确定岩石节理粗糙度系数的研究[C]// 地下工程经验会论文选集. 北京：地质出版社，1986：343-348.(WANG Qi. The study of the determination of rock mass joints roughness coefficient by using elongation R[C]// The Selections of Conference of Underground Engineering Experience. Beijing：Geology Press，1986：343-348.(in Chinese))
[11]	陈世江，朱万成，王创业，等. 岩体结构面粗糙度系数定量表征研究进展[J]. 力学学报，2017，49(2)：239-256.(CHEN Shijiang，ZHU Wancheng，WANG Chuangye，et al. Review of research progresses of the quantifying joint roughness coefficient[J]. Chinese Journal of Theoretical and Applied Mechanics，2017，49(2)：239-256.(in Chinese))
[16]	MAERZ N H ，FRANKLIN J A ，BENNETT C P. Joint roughness measurement using shadow profilometry[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts，1990，27(5)：329-343.
[13]	杜时贵. 简易纵剖面仪及其在岩体结构面粗糙度系数研究中的应用[J]. 地质科技情报，1992，(3)：91-95.(DU Shigui. Simple profile instrument and its application on studying joint roughness coefficient of rock[J]. Geological Science and Technology Information，1992，(3)：91-95.(in Chinese))