岩石–混凝土界面峰值剪切强度经验公式试验研究

doi:10.13722/j.cnki.jrme.2022.1266

Abstract
Figure/Table
References (0)
Related Citation (15)

Download: PDF (1723 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract In order to study the relationship between the shear bearing capacity of the rock-concrete interface and the mechanical properties of rock and concrete，the irregular joint specimens of fine-grained sandstone，silty-grained marble，granite and coarse-grained marble were prepared by using a splitting method，the rock joint morphological parameters were obtained by a three-dimensional topography scanner，and then the rock-concrete interface specimens were made by pouring concrete on the rock joint surface. Finally，direct shear tests were carried out on rock-concrete interface specimens under different normal stresses by using the RDS–200 rock joint shear test system. The results show that the peak shear strength of rock-concrete interface and concrete joint increases with the increase in normal stress，and the former always increases faster than the latter under the same normal stress；the average peak shear strength of the rock-concrete interface has a good exponential correlation with the average pre-peak shear stiffness of rock-concrete interface. With the increase of the difference between the elastic modulus of rock and concrete，the internal friction angle of the rock-concrete interface decreases linearly，the cohesion of the rock-concrete interface increases linearly，and the peak shear bearing mode of the rock-concrete interface gradually changes from the friction bearing mode to the combined bearing mode of friction and cohesion. Therefore，an empirical formula of the peak shear strength of the rock-concrete interface in the form of Mohr-Coulomb criterion is proposed. Based on the power relationship between the concrete wall sharing coefficient in the rock-concrete interface compressive strength and the basic friction angle of rock joint，a new method for determining the rock-concrete interface compressive strength JCSab is proposed，and an empirical formula of peak shear strength of rock-concrete interface in the form of JRC-JCS model is established. Through the comparison and verification between the calculated values and the test values of the peak shear strength of the rock-concrete interface，it is found that the two newly proposed empirical formulas can better predict the peak shear strength of the rock-concrete interface，and the parameters are easy to obtain，which can provide a reference for the estimation of the peak shear strength of the rock-concrete interface in engineering practice.

Key words： rock mechanics rock-concrete interface direct shear test peak shear strength empirical formula basic friction angle

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	LIU Jianghao1
	GUO Baohua1
	2
	3
	CHENG Tan1
	SUN Jiehao1
	TIAN Shixuan1
	CHEN Yan1

Cite this article:

LIU Jianghao1,GUO Baohua1,2, et al. Experimental study on empirical formula of peak shear strength for rock-concrete interface #br#[J]. , 2023, 42(10): 2552-2565.

URL:

https://rockmech.whrsm.ac.cn/EN/10.13722/j.cnki.jrme.2022.1266 OR https://rockmech.whrsm.ac.cn/EN/Y2023/V42/I10/2552

[1]	谢和平，陈忠辉，易成，等. 基于工程体-地质体相互作用的接触面变形破坏研究[J]. 岩石力学与工程学报，2008，27(9)：1 767-1 780.(XIE Heping，CHEN Zhonghui，YI Cheng，et al. Research on deformation and failure of interface based on interaction between structural body and geo-body[J]. Chinese Journal of Rock Mechanics and Engineering，2008，27(9)：1 767-1 780.(in Chinese))
[2]	邵珠山，席慧慧，乔汝佳，等. 运营隧道衬砌裂损与治理修复措施研究综述[J]. 现代隧道技术，2022，59(4)：29-39.(SHAO Zhushan，XI Huihui，QIAO Rujia，et al. Review of the research on lining damage and repair measures for tunnelsin operation[J]. Modern Tunnelling Technology，2022，59(4)：29-39.(in Chinese))
[3]	王洪德，魏梓桐，马云东. 隧道衬砌结构病害风险优度评价[J]. 辽宁工程技术大学学报：自然科学版，2022，41(2)：103-108.(WANG Hongde，WEI Zitong，MA Yundong. Risk priority degree assessment of structural diseases on tunnel lining[J]. Journal of Liaoning Technical University：Natural Science，2022，41(2)：103-108.(in Chinese))
[4]	李仕胜. 小湾坝体混凝土与基岩接触面抗剪强度研究[J]. 云南水力发电，1997，(4)：24-26.(LI Shisheng. Study on shear strength of interface between concrete and bedrock of Xiaowan dam[J]. Yunnan Water Power，1997，(4)：24-26.(in Chinese))
[5]	杨令强，李园园，林明强. 门楼水库溢流坝段岩石与混凝土抗剪参数的确定[J]. 岩土力学，2008，29(增1)：515-518.(YANG Lingqiang，LI Yuanyuan，LIN Mingqiang. Determination of shear strength between rock mass and concrete in Menlou overflow dam monolith[J]. Rock and Soil Mechanics，2008，29(Supp.1)：515-518.(in Chinese))
[6]	蔡耀军，徐福兴. 大坝建基岩体抗剪强度取值[J]. 岩石力学与工程学报，2002，21(7)：1 040-1 044.(CAI Yaojun，XU Fuxing. Determination of the rockmass shear strength on the dam foundation[J]. Chinese Journal of Rock Mechanics and Engineering，2002，21(7)：1 040-1 044.(in Chinese))
[7]	黎思幸，练继建. 齿型基岩面法改善重力坝坝基抗滑稳定性[J]. 天津大学学报，2001，34(6)：793-795.(LI Sixing，LIAN Jijian. Improvement of anti-sliding stability of gravity dam foundation by tooth bedrock surface method[J]. Journal of Tianjin University，2001，34(6)：793-795.(in Chinese))
[8]	朱浮声，笪盍. 矿山巷道衬砌破坏的综合分析[J]. 金属矿山，1986，(11)：30-32.(ZHU Fusheng，YUN Yun. Comprehensive analysis of lining failure of mine roadway[J]. Metal Mine，1986，(11)：30-32.(in Chinese))
[9]	岳娟，盛金昌，王惠民，等. 岩石-混凝土界面抗剪强度劣化研究及进展[J]. 水利水电科技进展，2022，42(5)：15-21.(YUE Juan，SHENG Jinchang，WANG Huimin，et al. Research and progress on shear strength deterioration of rock concrete interface[J]. Advances in Science and Technology of Water Resources，2022，42(5)：15-21.(in Chinese))
[10]	PATTON F D. Multiple modes of shear failure in rock[C]// Proceedings of the 1st Congress of International Society of Rock Mechanics. Lisbon，Portugal：[s. n.]，1966：509-513.
[11]	BARTON N. Review of a new shear strength criterion for rock joints[J]. Engineering Geology，1973，7(4)：287-332.
[12]	JOHNSTON I W，LAM T S K. Frictional characteristics of planar concrete-rock interfaces under constant normal stiffness conditions[C]// Proceedings of the 4th ANZ Conference on Geomechanics. Perth：[s. n.]，1984：105-108.
[13]	JOHNSTON I W，LAM T S K. Shear behaviour of regular triangular concrete/rock joints-analysis[J]. Journal of Geotechnical Engineering，1989，115(5)：711-727.
[14]	LAM T S K，JOHNSTON I W. Shear behaviour of regular triangular concrete/rock joints-evaluation[J]. Journal of Geotechnical Engineering，1989，115(5)：728-740.
[15]	KODIKARA J K，JOHNSTON I W. Shear behaviour of irregular triangular rock-concrete joints[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts，1994，31(4)：313-322.
[16]	HABERFIELD C M，SEIDEL J P. Some recent advances in the modelling of soft rock joints in direct shear[J]. Geotechnical and Geological Engineering，1999，17(3-4)：177-195.
[17]	JIANG Q，YANG Y，YAN F，et al. Deformation and failure behaviours of rock-concrete interfaces with natural morphology under shear testing[J]. Construction and Building Materials，2021，293(7)，DOI：10.1016/j.conbuildmat.2021.123468.
[18]	ANDJELKOVIC V，PAVLOVIC N，LAZAREVIC Z，et al. Modelling of shear characteristics at the concrete-rock mass interface[J]. International Journal of Rock Mechanics and Mining Sciences，2015，76：222-236.
[19]	宋磊博，江权，李元辉，等. 软-硬自然节理的改进JRC-JCS剪切强度公式[J]. 岩土力学，2017，38(10)：2 789-2 798.(SONG Leibo，JIANG Quan，LI Yuanhui，et al. Improved JRC-JCS shear strength formula for soft-hard natural joints[J]. Rock and Soil Mechanics，2017，38(10)：2 789-2 798.(in Chinese))
[20]	金磊磊，魏玉峰. 基于三维形貌和剪胀效应的软-硬节理抗剪强度模型[J]. 工程力学，2020，37(12)：180-190.(JIN Leilei，WEI Yufeng. Calculation model for the shear strength of soft-hard joints based on three-dimensional morphology and dilatancy effect[J]. Engineering Mechanics，2020，37(12)：180-190.(in Chinese))
[21]	张雅慧，汪丁建，唐辉明，等. 基于PFC～(2D)数值试验的异性结构面剪切强度特性研究[J]. 岩土力学，2016，37(4)：1 031-1 041. (ZHANG Yahui，WANG Dingjian，TANG Huiming，et al. Study of shear strength characteristics of heterogeneous discontinuities using PFC～(2D) simulation[J]. Rock and Soil Mechanics，2016，37(4)：1 031-1 041.(in Chinese))
[22]	范祥，邓志颖，崔志猛，等. 一种新的软-硬节理峰值剪切强度模型[J]. 岩土力学，2021，42(7)：1 861-1 870.(FAN Xiang，DENG Zhiying，CUI Zhimeng，et al. A new peak shear strength model for soft-hard joint[J]. Rock and Soil Mechanics，2021，42(7)：1 861-1 870. (in Chinese))
[23]	TORSÆTER M，TODOROVIC J，LAVROV A. Structure and debonding at cement-steel and cement-rock interfaces：effect of geometry and materials-sciencedirect[J]. Construction and Building Materials，2015，96：164-171.
[24]	SHEN Y，WANG Y，YANG Y，et al. Influence of surface roughness and hydrophilicity on bonding strength of concrete-rock interface[J]. Construction and Building Materials，2019，213：156-166.
[25]	TIAN H M，CHEN W Z，YANG D S，et al. Experimental and numerical analysis of the shear behaviour of cemented concrete-rock joints[J]. Rock Mechanics and Rock Engineering，2014，48(1)：213-222.
[26]	SAIANG D，MALMGREN L，NORDLUND E. Laboratory tests on shotcrete-rock joints in direct shear，tension and compression[J]. Rock Mechanics and Rock Engineering，2005，38(4)：275-297.
[27]	SOLTANIANFARD M A，TOUFIGH V，GHAEMIAN M. The interface behavior of rock，conventional vibrated and roller compacted concrete[J]. Geotechnical and Geological Engineering：An International Journal，2020，38(4)：1 949-1 969.
[28]	陈记，徐卫亚，朱珍德，等. 基岩-混凝土胶结面剪切强度JRC-JCS模型研究[J]. 河海大学学报：自然科学版，2003，31(4)：407-410.(CHEN Ji，XU Weiya，ZHU Zhende，et al. Study on JRC-JCS model of shear strength of bedrock-concrete interface[J]. Journal of Hohai University：Natural Science，2003，31(4)：407-410.(in Chinese))
[29]	易成，李志兵，刘晋艳，等. 两种介质接触面剪切力学性能的试验研究[J]. 岩土工程学报，2009，31(9)：1 317-1 323.(YI Cheng，LI Zhibing，LIU Jinyan，et al. Experimental study on shear mechanical behaviors of interface between two kinds of media[J]. Chinese Journal of Geotechnical Engineering，2009，31(9)：1 317-1 323.(in Chinese))
[30]	LI C C，ZHANG N，RUIZ J. Measurement of the basic friction angle of planar rock discontinuities with three rock cores[J]. Bulletin of Engineering Geology and the Environment，2019，78(2)：847-856.
[31]	中华人民共和国行业标准编写组. SL/T264—2020 水利水电工程岩石试验规程[S]. 北京：中国水利水电出版社，2020.(The Professional Standards Compilation Group of Peoples? Republic of China. SL/T264—2020 Specifications for rock tests in water conservancy and hydroelectric engineering[S]. Beijing：China Water Power Press，2020.(in Chinese))
[32]	董航宇. 不规则岩石节理剪切力学特性试验研究[硕士学位论文][D]. 焦作：河南理工大学，2017.(DONG Hangyu. Experimental study on mechanical shear properties of irregular rock fractures[M. S. Thesis][D]. Jiaozuo：Henan Polytechnic University，2017.(in Chinese))
[33]	郭保华，程坦，陈岩，等. 大理岩裂隙渗流特性及充填砂土影响[J]. 水利学报，2019，50(4)：463-474.(GUO Baohua，CHENG Tan，CHEN Yan，et al. Seepage characteristic of marble fracture and effect of filling sands[J]. Journal of Hydraulic Engineering，2019，50(4)：463-474.(in Chinese))
[34]	LI Y，ZHANG Y. Quantitative estimation of joint roughness coefficient using statistical parameters[J]. International Journal of Rock Mechanics and Mining Sciences，2015，77：27-35.
[35]	YANG Z Y，LO S C，DI C C. Reassessing the joint roughness coefficient(JRC) estimation using Z2[J]. Rock Mechanics and Rock Engineering，2001，34(3)：243-251.
[36]	程坦，郭保华，孙杰豪，等. 非规则岩石节理峰值剪切试验与强度经验公式研究[J]. 岩石力学与工程学报，2022，41(1)：93-105.(CHENG Tan，GUO Baohua，SUN Jiehao，et al. A strength empirical formula of irregular rock joints based on peak shear test[J]. Chinese Journal of Rock Mechanics and Engineering，2022，41(1)：93-105.(in Chinese))
[37]	孙杰豪，郭保华，田世轩，等. 峰前循环剪切作用下岩石节理剪切力学特性[J]. 岩土力学，2022，43(增2)：52-62.(SUN Jiehao，GUO Baohua，TIAN Shixuan，et al. Shear mechanical properties of rock joints under pre-peak cyclic shearing condition[J]. Rock and Soil Mechanics，2022，43(Supp.2)：52-62.(in Chinese))
[38]	雍睿，钟祯，杜时贵，等. 岩体结构面基本摩擦角研究现状与展望[J]. 岩石力学与工程学报，2022，41(2)：254-270.(YONG Rui，ZHONG Zhen，DU Shigui，et al. Review on research advance of basic friction angle of rock joints [J]. Chinese Journal of Rock Mechanics and Engineering，2022，41(2)：254-270.(in Chinese))
[39]	ALEJANO L R，MURALHA J，ULUSAY R，et al. ISRM suggested method for determining the basic friction angle of planar rock surfaces by means of tilt tests[J]. Rock Mechanics and Rock Engineering，2018，51(12)：3 853-3 859.