基于砂型3D打印的复杂节理岩体变形破坏特征试验研究

doi:10.13722/j.cnki.jrme.2023.0671

Abstract
Figure/Table
References (0)
Related Citation (15)

Download: PDF (14288 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract The deformation and failure characteristics of complex jointed rock mass has important theoretical and practical significance for the stability control of rock engineering. In order to overcome the difficulties of casting method in generating rock-like specimens with complex joints，and to investigate the effect of joint density on the deformation and failure characteristics of rock mass，sand-powder 3D printing is employed to generate rock-like specimens with complex joints based on Monte-Carlo method. By conducting uniaxial compression test with digital image correlation(DIC)，the effect of joint density on the mechanical behaviors，fracturing evolutions and failure patterns of rock mass has been investigated. The results show that：with the increase of the joint density，the peak strength and peak strain decrease exponentially，and the elastic modulus decreases linearly. Meanwhile，the pre-peak energy，elastic strain energy，dissipative energy and post-peak surplus energy decrease exponentially，while the post-peak release energy decreases linearly. Both the location and dip angle of joints affect the initiation and propagation of cracks；with the increase of joint density，the initiated cracks are more tend to propagate along a specific path，and the control effect of joint on crack propagation becomes more significant. The results provide a new method for the experimental test of complex jointed rock mass，and provide theoretical reference for the deformation failure mechanism and stability analysis of complex jointed rock mass.

Key words： rock mechanics sand-powder 3D printing complex jointed rock mass joint density mechanical behavior failure characteristic

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	WANG Wenhai
	JIANG Lishuai
	HE Xin
	WANG Zongke
	ZHAO Ye

Cite this article:

WANG Wenhai,JIANG Lishuai,HE Xin, et al. Experimental study on deformation and failure characteristic of complex jointed rock mass based on sand-powder 3D printing#br#[J]. , 2024, 43(3): 754-767.

URL:

http://rockmech.whrsm.ac.cn/EN/10.13722/j.cnki.jrme.2023.0671 OR http://rockmech.whrsm.ac.cn/EN/Y2024/V43/I3/754

[1]	谢和平，陈忠辉. 岩石力学[M]. 北京：科学出版社，2004：45-60.(XIE Heping，CHEN Zhonghui. Rock mechanics[M]. Beijing：Science Press，2004：45-60.(in Chinese))
[10]	王佩新，曹平，蒲成志，等. 单压下节理密度及倾角对类岩石试件强度及变形的影响[J]. 工程科学学报，2017，39(4)：494-501.(WANG Peixin，CAO Ping，PU Chengzhi，et al. Effect of the density and inclination of joints on the strength and deformation properties of rock-like specimens under uniaxial compression[J]. Chinese Journal of Engineering Science，2017，39(4)：494-501. (in Chinese))
[14]	GELL，ELEANOR M WALLEY，STEPHEN M BRAITHWAITE，et al. Review of the validity of the use of artificial specimens for characterizing the mechanical properties of rocks[J]. Rock Mechanics and Rock Engineering，2019，52(9)：2 949-2 961.
[16]	SONG R，WANG Y，ISHUTOV S，et al. A comprehensive experimental study on mechanical behavior，microstructure and transport properties of 3D-printed rock analogs[J]. Rock Mechanics and Rock Engineering，2020，53：5 745-5 765.
[19]	TIAN W，HAN N V. Mechanical properties of rock specimens containing pre-existing flaws with 3D printed materials[J]. Strain，2017；53：e12240.
[23]	刘享华，张科，李娜，等. 含孔双裂隙3D打印类岩石试件破裂行为定量识别[J]. 岩土力学，2021，42(11)：3 017-3 028. (LIU Xianghua，ZHANG Ke，LI Na，et al. Quantitative identification of the failure behavior of the 3D printed rock-like specimen with one hole and two flaws[J]. Rock and Soil Mechanics，2021，42(11)：3 017- 3 028.(in Chinese))
[25]	XU Q，JIANG L，MA C，et al. Effect of layer thickness on the physical and mechanical properties of sand powder 3D printing specimens[J]. Frontiers in Earth Science，DOI：10.3389/feart.2021.763202.
[28]	金爱兵，陆通，王本鑫，等. 基于力学等效的岩体关键节理迹长阈值研究[J]. 岩石力学与工程学报，2022，41(5)：904-915. (JIN Aibing，LU Tong，WANG Benxin，et al. Study on the length threshold of key joint trace in rock mass based on mechanical equivalence[J]. Chinese Journal of Rock Mechanics and Engineering，2022，41(5)：904-915.(in Chinese))
[32]	谢和平，鞠杨，黎立云. 基于能量耗散与释放原理的岩石强度与整体破坏准则[J]. 岩石力学与工程学报，2005，24(17)：3 003-3 010. (XIE Heping，JU Yang，LI Liyun. Criteria for strength and structural failure of rocks based on energy dissipation and energy release principles[J]. Chinese Journal of Rock Mechanics and Engineering，2005，24(17)：3 003-3 010.(in Chinese))
[34]	金爱兵，王树亮，王本鑫，等. 基于DIC技术的3D打印节理试件破裂机制研究[J]. 岩土力学，2020，41(10)：3 214-3 224.(JIN Aibing，WANG Shuliang，WANG Benxin，et al. Study on the fracture mechanism of 3D-printed-joint specimens based on DIC technology[J]. Rock and Soil Mechanics，2020，41(10)：3 214-3 224. (in Chinese))
[6]	陈超，王伟，许高杰，等. 考虑不同节理倾角和贯通率的类岩材料单轴压缩试验[J]. 河海大学学报：自然科学版，2022，50(5)：124-130.(CHEN Chao，WANG Wei，XU Gaojie，et al. Uniaxial compression test of rock-like material considering different joint inclinations and penetration rates[J]. Journal of Hohai University：Natural Science，2022，50(5)：124-130.(in Chinese))
[8]	DOU L，YANG K，CHI X. Fracture behavior and acoustic emission characteristics of sandstone samples with inclined precracks[J]. International Journal of Coal Science and Technology，2021，8：77-87.
[15]	ZHANG K，QI F，BAO R，et al. Physical reconstruction and mechanical behavior of fractured rock masses[J]. Bull Eng Geol Environ，2021，80：4 441-4 457.
[24]	VOGLER D，WALSH S，DOMBROVSKI E，et al. A comparison of tensile failure in 3D-printed and natural sandstone[J]. Engineering Geology，2017：221-235.
[18]	KONG L，OSTADHASSAN M，LI C，et al. Rock physics and geomechanics of 3D printed rocks[C]// ARMA US Rock Mechanics/Geomechanics Symposium. [S. l.]：[s. n.]，2017：776.
[4]	蒋力帅. 工程岩体劣化与大采高沿空巷道围岩控制原理研究[博士学位论文][D]. 北京：中国矿业大学(北京)，2016.(JIANG Lishuai. Study on weakening of engineering rockmass and control principle of gob-side entry in large height mining condition[Ph. D. Thesis][D]. Beijing：China University of Mining and Technology(Beijing)，2016.(in Chinese))
[5]	靳瑾，曹平，蒲成志. 预制裂隙几何参数对类岩材料破坏模式及强度的影响[J]. 中南大学学报：自然科学版，2014，45(2)：529-535.(JIN Jin，CAO Ping，PU Chengzhi. Influence of flaw parameters on damage mode and strength of rock-like materials[J]. Journal of Central South University：Natural Science，2014，45(2)：529-535.(in Chinese))
[13]	YANG X X，JING H W，TANG C A，et al. Effect of parallel joint interaction on mechanical behavior of jointed rock mass models[J]. International Journal of Rock Mechanics and Mining Science and Geomechanics Abstracts，2016，92：40-53.
[17]	裴志茹. 基于CT扫描及3D打印技术裂隙岩体试样力学特性研究[硕士学位论文][D]. 西安：长安大学，2018.(PEI Zhiru. A study on mechanical characteristics of flawed rock mass specimens based on CT scanning and 3D printing technology[M. S. Thesis][D]. Xi?an：Chang?an University，2018.(in Chinese))
[7]	王桂林，曹天赐，文兴祥，等. 单轴压缩下单节理砂岩峰前能量自我抑制演化规律[J]. 煤炭学报，2021，46(增1)：211-221. (WANG Guilin，CAO Tianci，WEN Xingxiang，et al. Evolution law of self-suppression of peak energy of single jointed sandstonen [J]. Journal of China Coal Society，2021，46(Supp.1)：211-221.(in Chinese))
[22]	FERESHTENEJAD S，SONG J J. Fundamental Study on applicability of powder-based 3D printer for physical modeling in rock mechanics[J]. Rock Mechanics and Rock Engineering，2016，49(6)：2 065-2 074.
[26]	ZHAO Y，JIANG L，LI C，et al. Experimental investigation into the mechanical behavior of jointed soft rock using sand powder 3D printing[J]. Rock Mechanics and Rock Engineering，2023，56(7)：5 383-5 404.
[31]	蒋力帅，王鑫哲，徐清，等. 砂型3D打印材料对类软岩力学特性影响规律及机理[J/OL]. 煤炭科学技术，DOI：10.12438/cst.2022-2060.(JIANG Lishuai，WANG Xinzhe，XU Qing，et al. Influence and mechanism of printing materials on the mechanical properties of sand powder 3D printed soft rock-like materials[J/OL]. Coal Science and Technology，DOI：10.12438/cst.2022-2060.(in Chinese))
[33]	刘刚，肖福坤，秦涛. 小尺寸效应下岩石力学特性及声发射规律[J]. 岩石力学与工程学报，2018，37(增2)：3 905-3 917. (LIU Gang，XIAO Fukun，QIN Tao. Rock mechanics characteristics and acoustic emission rule under small-size effect[J]. Chinese Journal of Rock Mechanics and Engineering，2018，37(Supp.2)：3 905-3 917. (in Chinese))
[30]	蔡美峰. 岩石力学与工程[M]. 北京：科学出版社，2002：50-72.(CAI Meifeng. Rock mechanics and engineering[M]. Beijing：Science Press，2002：50-72.(in Chinese))
[2]	吴琼. 复杂节理岩体力学参数尺寸效应及工程应用研究[博士学位论文][D]. 武汉：中国地质大学(武汉)，2012.(WU Qiong. The mechanical parameters of jointed rock mass：scale-effect research and its engineering application[Ph. D. Thesis][D]. Wuhan：China University of Geosciences(Wuhan)，2012.(in Chinese))
[3]	谢和平，高峰，鞠杨. 深部岩体力学研究与探索[J]. 岩石力学与工程学报，2015，34(11)：2 161-2 178.(XIE Heping，GAO Feng，JU Yang. Research and development of rock mechanics in deep ground engineering[J]. Chinese Journal of Rock Mechanics and Engineering，2015，34(11)：2 161-2 178.(in Chinese))
[9]	陈新，廖志红，李德建. 节理倾角及连通率对岩体强度、变形影响的单轴压缩试验研究[J]. 岩石力学与工程学报，2011，30(4)：781-789.(CHEN Xin，LIAO Zhihong，LI Dejian. Experimental study of effects of joint inclination angle and connectivity rate on strength and deformation properties of rock masses under uniaxial compression[J]. Chinese Journal of Rock Mechanics and Engineering，2011，30(4)：781-789.(in Chinese))
[11]	SAGONG M，BOBET A. Coalescence of multiple flaws in a rock-model material in uniaxial compression[J]. International Journal of Rock Mechanics and Mining Sciences，2002，39(2)：229-241.
[12]	PRUDENCIO M，JAN M V S. Strength and failure modes of rock mass models with non-persistent joints-ScienceDirect[J]. International Journal of Rock Mechanics and Mining Sciences，2007，44(6)：890-902.
[20]	PRIMKULOV B，CHALATURNYK J，CHALATURNYK R，et al. 3D printed sandstone strength：curing of furfuryl alcohol resin-based sandstones[J]. 3D Printing and Additive Manufacturing，2017，4(3)：149.
[21]	A K J H，A J A N，B R J C. Improvement of the unconfined compressive strength of 3D-printed model rock via silica sand functionalization using silane coupling agents[J]. International Journal of Adhesion and Adhesives，2018，85：274-280.
[27]	蒋力帅，吴星宇，王庆伟，等. 砂型3D打印类煤试样动静组合加载力学特性[J]. 煤炭学报，2022，47(3)：1 196-1 207.(JIANG Lishuai，WU Xingyu，WANG Qingwei，et al. Dynamic mechanical behaviors of sand-powder 3D printing rock-like specimens under coupled static and dynamic loads[J]. Journal of China Coal Society，2022，47(3)：1 196-1 207.(in Chinese))
[29]	金爱兵，陆通，王本鑫，等. 基于改进力学等效的岩体关键节理倾角特征试验研究[J]. 岩石力学与工程学报，2023，42(1)：76-87.(JIN Aibing，LU Tong，WANG Benxin，et al. Experimental study on the dip characteristics of key joints in rock mass based on improved mechanical equivalence[J]. Chinese Journal of Rock Mechanics and Engineering，2023，42(1)：76-87.(in Chinese))
[35]	唐庆腾. 裂隙网络岩体力学特性及其锚固作用机制研究[博士学位论文][D]. 徐州：中国矿业大学，2022.(TANG Qingteng. Research on the mechanical behavior and anchoring mechanism of rock-like material with discrete fracture network[Ph. D. Thesis][D]. Xuzhou：China University of Mining and Technology，2022.(in Chinese))