CNL及DNL两类边界条件下粗糙结构面剪切力学特性及破坏机制比较研究

doi:10.3724/1000-6915.jrme.2024.0610

Abstract
Figure/Table
References (0)
Related Citation (15)

Download: PDF (7191 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract The dynamic loads induced by excavation disturbance and earthquake significantly influence the deformation and instability of jointed rock masses. To investigate the shear mechanical properties of rock joints under dynamic normal load，a series of shear tests were conducted on red sandstones under both dynamic normal load(DNL) and constant normal load(CNL) boundary conditions. The test results，i.e.，shear strengths，failure modes，acoustic emission characteristics and failure pattern obtained under the two boundary conditions were comparatively analyzed. The analysis shows that the shear stress reflects was lagged the dynamic normal stress and the phase offset was positively correlated with the initial normal stress and joints roughness. The influence of dynamic normal load on peak shear strength depended on the failure mode. When the primary failure mode was climbing and dilation，the peak shear strength was increased by the dynamic normal load；conversely，when the failure mode was dominated by shearing and fracturing of asperities，the peak shear strength was decreased. The dilation was significantly confined by the dynamic normal load，which exacerbated the wear on joints surface and the degradation of asperities. The acoustic emission monitoring results indicated that the dynamic normal load intensified the damage degree at the initial shear stage. It increased the proportion of shear fractures whereas decreased the proportion of tensile fractures. Based on obtained test results and revealed shear mechanism，a dilatancy model was deduced considering the influence of the dynamic normal load. Finally，a model for predicting the peak shear strength of joints under DNL conditions was proposed and it was validated to have a satisfactory prediction accuracy.

Key words： rock mechanics dynamic normal load shear characteristics rough joints acoustic emission features failure mechanism shear strength model

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	ZHANG Xiaobo1
	2
	YI Le1
	2
	YAO Chi1
	2
	MA Yongli1
	2
	YANG Jianhua1
	2
	JIANG Qinghui3
	ZHOU Chuangbing1
	2

Cite this article:

ZHANG Xiaobo1,2,YI Le1, et al. Comparative study on shear mechanical properties and failure mechanisms of rough joints under CNL and DNL boundary conditions[J]. , 2025, 44(4): 865-880.

URL:

https://rockmech.whrsm.ac.cn/EN/10.3724/1000-6915.jrme.2024.0610 OR https://rockmech.whrsm.ac.cn/EN/Y2025/V44/I4/865

[1]	ZHANG X B，JIANG Q H，CHEN N，et al. Laboratory investigation on shear behavior of rock joints and a new peak shear strength criterion[J]. Rock Mechanics and Rock Engineering，2016，49(9)：3 495-3 512.
[2]	HE M C，CHENG T，QIAO Y F，et al. A review of rockburst：Experiments，theories，and simulations[J]. Journal of Rock Mechanics and Geotechnical Engineering，2023，15(5)：1 312-1 353.
[3]	BARTON N. Shear strength criteria for rock，rock joints，rockfill and rock masses：Problems and some solutions[J]. Journal of Rock Mechanics and Geotechnical Engineering，2013，5(4)：249-261.
[4]	BAHAADDINI M，HAGAN P，MITRA R，et al. Numerical study of the mechanical behavior of nonpersistent jointed rock masses[J]. International Journal of Geomechanics，2016，16(1)：04015035.
[5]	ROUET-LEDUC B，HULBERT C，BOLTON D C，et al. Estimating fault friction from seismic signals in the laboratory[J]. Geophysical Research Letters，2018，45(3)：1 321-1 329.
[6]	刘新荣，郭雪岩，周小涵，等. 库岸危岩剪切带-基岩界面宏细观剪切贯通机制及力学特性研究[J]. 岩石力学与工程学报，2024，43(5)：1 096-1 109.(LIU Xinrong，GUO Xueyan，ZHOU Xiaohan，et al. Study on macro-meso shear transfixion mechanisms and mechanical properties of shear band-bedrock interfaces of dangerous rock on reservoir bank[J]. Chinese Journal of Rock Mechanics and Engineering，2024，43(5)：1 096-1 109.(in Chinese))
[7]	崔国建，张传庆，韩华超，等. CNL及CNS条件下结构面剪切特性试验研究[J]. 岩石力学与工程学报，2019，38(增2)：3 384- 3 392.(CUI Guojian，ZHANG Chuanqing，HAN Huachao，et al. Experiment study on shear behavior of artificial joint under CNL and CNS boundary conditions[J]. Chinese Journal of Rock Mechanics and Engineering，2019，38(Supp. 2)：3 384-3 392.(in Chinese))
[8]	尹乾，靖洪文，孟波，等. CNL 和 CNS 边界条件下砂岩宏细观剪切力学特性[J]. 采矿与安全工程学报，2021，38(3)：615-624.(YIN Qian，JING Hongwen，MENG Bo，et al. Macroscopic and microscopic shear mechanical properties of sandstone under CNL and CNS boundary conditions[J]. Journal of Mining and Safety Engineering，2021，38(3)：615-624.(in Chinese))
[9]	袁伟，李建春. 剪切速率对平直节理摩擦行为的影响及其机制研究[J]. 岩石力学与工程学报，2021，40(增2)：3 241-3 252.(YUAN Wei，LI Jianchun，Study on the effects and its mechanism of shear rate on friction of planar joints[J]. Chinese Journal of Rock Mechanics and Engineering，2021，40(Supp.2)：3 241-3 252.(in Chinese))
[10]	夏才初，宋英龙，唐志成，等. 粗糙节理剪切性质的颗粒流数值模拟[J]. 岩石力学与工程学报，2012，31(8)：1 545-1 552.(XIA Caichu，SONG Yinglong，TANG Zhicheng，et al. Particle flow numerical simulation for shear behavior of rough joints[J]. Chinese Journal of Rock Mechanics and Engineering，2012，31(8)：1 545-1 552. (in Chinese))
[11]	宋磊博，亢倩倩，杜时贵，等. 基于表面微凸体磨损特征演化规律的节理剪切强度各向异性机制研究[J]. 岩土力学，2021，42(9)：2 331-2 343.(SONG Leibo，KANG Qianqian，DU Shigui，et al. Anisotropy mechanism of shear strength based on wear and shear failure evolution of asperities of joint surface[J]. Rock and Soil Mechanics，2021，42(9)：2 331-2 343.(in Chinese))
[12]	刘日成，尹乾，杨瀚清，等. 恒定法向刚度边界条件下三维粗糙节理面循环剪切力学特性[J]. 岩石力学与工程学报，2021，40(6)：1 092-1 109.(LIU Richeng，YIN Qian，YANG Hanqing，et al. Cyclic shear mechanical properties of 3D rough joint surfaces under constant normal stiffness(CNS) boundary conditions[J]. Chinese Journal of Rock Mechanics and Engineering，2021，40(6)：1 092-1 109.(in Chinese))
[13]	蒋宇静，张孙豪，栾恒杰，等. 恒定法向刚度边界条件下锚固节理岩体剪切特性试验研究[J]. 岩石力学与工程学报，2021，40(4)：663-675.(JIANG Yujing，ZHANG Sunhao，LUAN Hengjie，et al. Experimental study on shear characteristics of bolted rock joints under constant normal stiffness boundary conditions[J]. Chinese Journal of Rock Mechanics and Engineering，2021，40(4)：663-675.(in Chinese))
[14]	HAN G S，JING H W，JIANG Y J，et al. Effect of cyclic loading on the shear behaviours of both unfilled and infilled rough rock joints under constant normal stiffness conditions[J]. Rock Mechanics and Rock Engineering，2020，53(5)：31-57.
[15]	尹敬涵，崔臻，盛谦，等. 循环荷载作用下岩石劈裂结构面剪切力学特性演化与影响因素研究[J]. 岩土力学，2023，44(1)：109-118.(YIN Jinghan，CUI Zhen，SHENG Qian，et al. Shear mechanical characteristics evolution and influencing factors of rock discontinuities under cyclic loading[J]. Rock and Soil Mechanics，2023，44(1)：109-118.(in Chinese))
[16]	杨嘉楠，范鹏贤，王明洋. 低频重复扰动下预加应力结构面变形破坏特性试验研究[J]. 岩石力学与工程学报，2023，42(7)：1 720-1 730. (YANG Jianan，FAN Pengxian，WANG Mingyang. Deformation and failure characteristics of pre-stressed joints under repeated low frequency disturbances[J]. Chinese Journal of Rock Mechanics and Engineering，2023，42(7)：1 720-1 730.(in Chinese))
[17]	DANG W G，KONIETZKY H，FRUEHWIRT T. Direct shear behavior of planar joints under cyclic normal load conditions：effect of different cyclic normal force amplitudes[J]. Rock Mechanics and Rock Engineering，2017，50(11)：3 101-3 107.
[18]	GONG H L，WANG G，LUO Y，et al. Shear fracture behaviors and acoustic emission characteristics of granite with discontinuous joints under combinations of normal static loads and dynamic disturbances[J]. Theoretical and Applied Fracture Mechanics，2023，125(5)：103923.
[19]	代万里，张强，谷邱鑫，等. 法向动载条件下粗糙岩质节理面剪切力学特性试验研究[J]. 岩石力学与工程学报，2024，43(7)：1 751-1 762.(DAI Wanli，ZHANG Qiang，GU Qiuxin，et al. Experimental study on the shear mechanical behaviors of a rough rock joint surface under dynamic normal load boundary condition[J]. Chinese Journal of Rock Mechanics and Engineering，2024，43(7)：1 751-1 762.(in Chinese))
[20]	BARTON N，CHOUBEY V. The shear strength of rock joints in theory and practice[J]. Rock Mechanics，1977，10(1)：1-54.
[21]	ZHANG X B，JIANG Q H，KULATILAKE P H S W，et al. Influence of asperity morphology on failure characteristics and shear strength properties of rock joints under direct shear tests[J]. International Journal of Geomechanics，2019，19(2)：04018196.
[22]	夏元友，吝曼卿，廖璐璐，等. 大尺寸试件岩爆试验岩屑分形特征分析[J]. 岩石力学与工程学报，2014，33(7)：1 358-1 365.(XIA Yuanyou，LIN Manqing，LIAO Lulu，et al. Fractal characteristic analysis of fragments from rockburst tests of large-diameter specimens[J]. Chinese Journal of Rock Mechanics and Engineering，2014，33(7)：1 358-1 365.(in Chinese))
[23]	焦峰，许江，彭守建，等. 常法向刚度条件下人工结构面剪切力学特性及损伤演化规律试验研究[J]. 煤炭学报，2023，48(11)：4 065-4 077.(JIAO Feng，XU Jiang，PENG Shoujian，et al. Experimental study on shear mechanical properties and damage evolution of artificial structural plane under condition normal stiffness[J]. Journal of China Coal Society，2023，48(11)：4 065-4 077.(in Chinese))
[24]	何满潮，赵菲，杜帅，等. 不同卸载速率下岩爆破坏特征试验分析[J]. 岩土力学，2014，35(10)：2 737-2 747.(HE Manchao，ZHAO Fei，DU Shuai，et al. Rockburst characteristics based on experimental tests under different unloading rates[J]. Rock and Soil Mechanics，2014，35(10)：2 737-2 747.(in Chinese))
[25]	CHEN Y D，ZHANG C Y，ZHAO Z H，et al. Shear behavior of artificial and natural granite fractures after heating and water?cooling treatment[J]. Rock Mechanics and Rock Engineering，2020，53(12)：5 429-5 449.
[26]	王聚贤，梁鹏，张艳博，等. 基于声发射RA-AF值与Kneedle算法的岩石拉剪破裂分类研究[J]. 岩石力学与工程学报，2024，43(增1)：3 267-3 279.(WANG Juxian，LIANG Peng，ZHANG Yanbo，et al. Research on classification of rock tensile-shear fracture based on acoustic emission RA-AF values and Kneedle algorithm[J]. Chinese Journal of Rock Mechanics and Engineering，2024，43(Supp.1)：3 267-3 279.(in Chinese))
[27]	Federation of Construction Materials Industries. JCMS-III B5706 Monitoring method for active cracks in concrete by acoustic emission[S]. [S. l.]：Federation of Construction Materials Industries，2003.
[28]	常新科，吴顺川，程海勇，等. 深部灰岩劈裂破坏的声发射损伤表征[J]. 科学技术与工程，2023，23(31)：13 525-13 532.(CHANG Xinke，WU Shunchuan，CHENG Haiyong，et al. Acoustic emission damage characterization of deep limestone under Brazilian splitting load[J]. Science Technology and Engineering，2023，23(31)：13 525-13 532.(in Chinese))
[29]	DU K，LI X F，TAO M，et al. Experimental study on acoustic emission (AE) characteristics and crack classification during rock fracture in several basic lab tests[J]. International Journal of Rock Mechanics and Mining Sciences，2020，133(6)：104411.
[30]	吴顺川，甘一雄，任义，等. 基于RA与AF值的声发射指标在隧道监测中的可行性[J]. 工程科学学报，2020，42(6)：723-730.(WU Shunchuan，GAN Yixiong，REN Yi，et al. Feasibility research of AE monitoring index in tunnel based on RA and AF[J]. Chinese Journal of Engineering，2020，42(6)：723-730.(in Chinese))
[31]	PATTON F D. Multiple modes of shear failure in rock[C]// Proceeding of the 1st Congress of International Society for Rock Mechanics. Lisbon，Portugal：[s. n.]，1966：509-513.
[32]	BARTON N. Review of a new shear strength criterion for rock joints[J]. Engineering Geology，1973，7(4)：287-332