含不同裂隙倾角瓦斯预抽钻孔破坏临界角度的确定

doi:10.3724/1000-6915.jrme.2024.0639

Abstract
Figure/Table
References (0)
Related Citation (15)

Download: PDF (2800 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract To investigate the fracture evolution and critical damage angle around gas pre-pumping boreholes, we conducted 3D-VIC observation tests under uniaxial compression on coal samples with varying initial fracture angles (0°, 30°, 45°, 60°, 90°). We computed time-series images of the surface deformation of the samples under different stress states, as well as their full-field strains during the destructive process. The characteristics of surface deformation and fracture evolution in borehole-fracture composite coals with differing fracture inclination angles were accurately characterized. The results indicate the following: (1) Localized bands emerge in the strain field during the elastic deformation stage. A “sudden” phenomenon occurs when the pre-fabricated fissure inclination angle is 45°, where the time interval between new crack initiation and surface penetration is relatively short. Localized zones emerge in the vicinity of boreholes and pre-existing fissures, making them more susceptible to damage during the crack initiation and expansion stages. (2) The fracture angle of the cracks significantly influences the specimen’s deformation under axial load. The tips of prefabricated fissures with varying angles concentrate and accumulate stress as axial stress levels increase, leading the samples to undergo a yielding-rupture process. The initial fracture angle of 45° represents the critical angle for destabilization damage in borehole-fracture composite coals, at which point the drilling deformation damage degree reaches a maximum of 23.42%. (3) As the initial prefabricated fracture angles increase, the damage degree of the borehole exhibits a linear upward trend when the fracture inclination angle is less than 45°, expressed as . Conversely, it follows a negative exponential downward trend for fracture inclination angles ranging from 45° to 90°, expressed as . This model demonstrates a good fit and effectively predicts the damage degree of borehole-fracture composite coals. These conclusions highlight that initial fracture angles play a crucial role in the development of fractures around boreholes during gas pre-pumping processes. The stress concentration at the crack tip is greatest, the deterioration effect is most pronounced, and the bearing capacity is lowest at the initial fracture angle of 45°, which is identified as the critical damage angle for borehole-fracture composite coals. These findings provide a foundation for assessing the destabilized damage state of gas pre-pumping boreholes.

Key words： mining engineering gas extraction rift angle fracture evolution drilling destruction degree critical damage angle

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	ZHANG Tianjun1
	2
	MENG Wei1
	PANG Mingkun1
	2
	ZHANG Hang1
	TIAN Jiawei1
	PAN Hongyu1
	2

Cite this article:

ZHANG Tianjun1,2,MENG Wei1, et al. Determination of critical angle of damage for gas pre-pumping boreholes with various crack inclinations[J]. , 2025, 44(S2): 58-69.

URL:

https://rockmech.whrsm.ac.cn/EN/10.3724/1000-6915.jrme.2024.0639 OR https://rockmech.whrsm.ac.cn/EN/Y2025/V44/IS2/58

[1] 林柏泉，张建国. 矿井瓦斯抽采理论与技术[M]. 徐州：中国矿业大学出版社，1996：66–123.(LIN Boquan，ZHANG Jianguo. Theory and technology of mine gas extraction[M]. Xuzhou：China University of Mining and Technology Press，1996：66–123.(in Chinese))
[2] 段伟华. 大采高工作面片帮机制及控制技术研究[J]. 煤炭科学技术，2020，48(3)：147–153.(DUAN Weihua. Study on mechanism and control technology of rib spalling in large mining height working face[J]. Coal Science and Technology，2020，48(3)：147–153.(in Chinese))
[3] LIU Y K，ZHOU F B，WANG J L，et al. Approach to increasing the quality of pressure-relieved gas drained from protected coal seam using surface borehole and its industrial application[J]. International Journal of Coal Science and Technology，2015，2(1)：46–51.
[4] 周福宝，孙玉宁，李海鉴，等. 煤层瓦斯抽采钻孔密封理论模型与工程技术研究[J]. 中国矿业大学学报，2016，45(3)：433–439. (ZHOU Fubao，SUN Yuning，LI Haijian，et al. Research on the theoretical model and engineering technology of the coal seam gas drainage hole sealing[J]. Journal of China University of Mining and Technology，2016，45(3)：433–439.(in Chinese))
[5] 赵怡晴，秦文静，金爱兵，等. 煤岩孔裂隙结构特征对其损伤演化规律影响研究[J]. 煤炭科学技术，2025，53(5)：90–101.(ZHAO Yiqing，QIN Wenjing，JIN Aibing，et al. Investigation on the influence of pore-fracture structure characteristics of coal rock on its damage evolution law[J]. Coal Science and Technology，2025，53(5)：90–101.(in Chinese))
[6] MOGI K. Source locations of elastic shocks in the fracturing processes in rocks[J]. Bulletin of the Earthquake Research Institute，1968，46(Supp. l)：1 103–1 125.
[7] 胡明明，周辉，张勇慧，等. 单轴加载过程中砂岩声学特性研究[J]. 岩土力学，2018，39(12)：4 468–4 474.(HU Mingming，ZHOU Hui，ZHANG Yonghui，et al. Analysis of acoustic property of sandstone under uniaxial loading[J]. Rock and Soil Mechanics，2018，39(12)：4 468–4 474.(in Chinese))
[8] WU L X，LIU S J，WU Y H，et al. Changes in IR with rock deformation[J]. International Journal of Rock Mechanics and Mining Sciences，2002，39(6)：825–831.
[9] 马少鹏，王来贵，赵永红. 岩石圆孔结构破坏过程变形场演化的试验研究[J]. 岩土力学，2006，27(7)：1 082–1 086.(MA Shaopeng，WANG Laigui，ZHAO Yonghong. Experimental study on deformation field evolution during failure procedure of a rock borehole structure[J]. Rock and Soil Mechanics，2006，27(7)：1 082–1 086.(in Chinese))
[10] XU J M，LIU F，CHEN Z Y，et al. Digital features of main constituents in granite during crack initiation and propagation[J]. Engineering Geology，2017，225(4)：96–102.
[11] TUONG L N，STEPHEN A H，PIERRE V，et al. Fracture mechanisms in soft rock：identification and quantification of evolving displacement discontinuities by extended digital image correlation[J]. Tectonophysics，2011，503(1/2)：117–128.
[12] 赵程，田加深，松田浩，等. 单轴压缩下基于全局应变场分析的岩石裂纹扩展及其损伤演化特性研究[J]. 岩石力学与工程学报，2015，34(4)：763–769.(ZHAO Cheng，TIAN Jiashen，MATSUDA Hiroshi，et al. Crack propagation and damage of rock under uniaxial compression based on global strain field analysis[J]. Chinese Journal of Rock Mechanics and Engineering，2015，34(4)：763–769.(in Chinese))
[13] 朱谭谭，靖洪文，苏海健，等. 孔洞–裂隙组合型缺陷砂岩力学特性试验研究[J]. 煤炭学报，2015，40(7)：1 518–1 525.(ZHU Tantan，JING Hongwen，SU Haijian，et al. Experimental investigation on mechanical behavior of sandstone with coupling effects under uniaxial compression[J]. Journal of China Coal Society，2015，40(7)：1 518–1 525.(in Chinese))
[14] 李术才，孙超群，许振浩，等. 基于无网格法的含缺陷岩石变形局部化数值模拟研究[J]. 岩土力学，2016，37(增1)：530–536.(LI Shucai，SUN Chaoqun，XU Zhenhao，et al. Numerical simulation of deformation localization for defective rock based on meshless method[J]. Rock and Soil Mechanics，2016，37(Supp.1)：530–536.(in Chinese))
[15] YANG S Q，YIN P F，ZHANG Y C，et al. Failure behavior and crack evolution mechanism of a non-persistent jointed rock mass containing a circular hole[J]. International Journal of Rock Mechanics and Mining Sciences，2019，114(1)：101–121.
[16] WU H，ZHAO G Y，LIANG W Z. Investigation of cracking behavior and mechanism of sandstone specimens with a hole under compression[J]. International Journal of Mechanical Sciences，2019，163(6)：1–16.
[17] 大久保诚介，汤杨，许江，等. 3D-DIC 系统在岩石力学试验中的应用[J]. 岩土力学，2019，40(8)：3 263–3 273.(SEISUKE Okubo，TANG Yang，XU Jiang，et al. Application of 3D-DIC system in rock mechanic test[J]. Rock and Soil Mechanics，2019，40(8)：3 263– 3 273.(in Chinese))
[18] 张天军，景晨，张磊，等. 含孔试样孔周破坏的应变局部化特征[J]. 煤炭学报，2020，45(12)：4 087–4 094.(ZHANG Tianjun，JING Chen，ZHANG Lei，et al. Strain localization characteristics of perforation failure of perforated specimens[J]. Journal of China Coal Society，2020，45(12)：4 087–4 094.(in Chinese))
[19] 张天军，张磊，李树刚，等. 含孔试样渐进性破坏的表面变形特征[J]. 煤炭学报，2017，42(10)：2 623–2 630.(ZHANG Tianjun，ZHANG Lei，LI Shugang，et al. Characteristics of the surface deformation of specimens with a hole during the progressive failure[J]. Journal of China Coal Society，2017，42(10)：2 623–2 630.(in Chinese))
[20] 张天军，纪翔，张磊，等. 瓦斯抽采钻孔孔周裂隙演化及等效裂纹宽度试验研究[J]. 岩石力学与工程学报，2019，38(增2)：3 625– 3 633.(ZHANG Tianjun，JI Xiang，ZHANG Lei，et al. Experimental study on evolution of circumferential crack and equivalent crack width of gas drilling borehole[J]. Chinese Journal of Rock Mechanics and Engineering，2019，38(Supp.2)：3 625–3 633.(in Chinese))
[21] 朱谭谭，靖洪文，苏海健，等. 含双圆形孔洞砂岩单轴压缩力学特性试验研究[J]. 岩土工程学报，2015，37(6)：1 047–1 056.(ZHU Tantan，JING Hongwen，SU Haijian，et al. Mechanical behavior of sandstone containing double circular cavities under uniaxial compression[J]. Chinese Journal of Geotechnical Engineering，2015，37(6)：1 047–1 056.(in Chinese))
[22] 李德行，王恩元，李楠，等. 单轴压缩下宏观裂纹倾角对煤体特性影响研究[J]. 岩石力学与工程学报，2017，36(增1)：3 206–3 213. (LI Dexing，WANG Enyuan，LI Nan，et al. Research on the coal characteristics of macro-crack dip angles under uniaxial compression[J]. Chinese Journal of Rock Mechanics and Engineering，2017，36(Supp.1)：3 206–3 213.(in Chinese))
[23] 中华人民共和国国家标准编写组. GB/T23561.7—2009 煤与岩石物理力学性质测定方法[S]. 北京：中国标准出版社，2009.(The National Standards Compilation Group of People?s Republic of China. GB/T23561.7—2009 Method for determination of physical and mechanical properties of coal and rock[S]. Beijing：China Standards Press，2009.(in Chinese))
[24] 董金玉，杨继红，杨国香，等. 基于正交设计的模型试验相似材料的配比试验研究[J]. 煤炭学报，2012，37(1)：44–49.(DONG Jinyu，YANG Jihong，YANG Guoxiang，et al. Research on similar material proportioning test of model test based on orthogonal design[J]. Journal of China Coal Society，2012，37(1)：44–49.(in Chinese))
[25] ZHU L. Research on the effect of prefabricated crack distribution about crack propagation[J]. Applied Mechanics and Materials，2014，31(47)：542–545.
[26] 张科，张凯. 裂隙砂岩变形破裂过程中应变场灰度及纹理特征分析[J]. 煤炭学报，2021，46(4)：1 253–1 262.(ZHANG Ke，ZHANG Kai. Gray and texture features of strain field for fractured sandstone during failure process[J]. Journal of China Coal Society，2021，46(4)：1 253–1 262.(in Chinese))
[27] 范杰，朱星，胡桔维，等. 基于3D-DIC的砂岩裂纹扩展及损伤监测试验研究[J]. 岩土力学，2022，43(4)：1 009–1 019.(FAN Jie，ZHU Xing，HU Juwei，et al. Experimental study on crack propagation and damage monitoring of sandstone using three-dimensional digital image correlation technology[J]. Rock and Soil Mechanics，2022，43(4)：1 009–1 019.(in Chinese))
[28] 李彦伟，姜耀东，杨英明，等. 煤单轴抗压强度特性的加载速率效应研究[J]. 采矿与安全工程学报，2016，33(4)：754–760.(LI Yanwei，JIANG Yaodong，YANG Yingming，et al. Research on loading rate effect of uniaxial compressive strength of coal[J]. Journal of Mining and Safety Engineering，2016，33(4)：754–760.(in Chinese))
[29] 李元海，林志斌，靖洪文，等. 含动态裂隙岩体的高精度数字散斑相关量测方法[J]. 岩土工程学报，2012，34(6)：1 060–1 068.(LI Yuanhai，LIN Zhibin，JING Hongwen，et al. High-accuracy digital speckle correlation method for rock with dynamic fractures[J]. Chinese Journal of Geotechnical Engineering，2012，34(6)：1 060–1 068.(in Chinese))
[30] 黎崇金，李夕兵，李地元. 含孔洞大理岩破坏特性的颗粒流分析[J]. 工程科学学报，2017，39(12)：1 791–1 801.(LI Chongjin，LI Xibing，LI Diyuan. Particle flow analysis of fracture characteristics of marble with a single hole[J]. Chinese Journal of Engineering，2017，39(12)：1 791–1 801.(in Chinese))
[31] 张晓平，王思敬，韩庚友，等. 岩石单轴压缩条件下裂纹扩展试验研究——以片状岩石为例[J]. 岩石力学与工程学报，2011，30(9)：1 772–1 781.(ZHANG Xiaoping，WANG Sijing，HAN Gengyou，et al. Crack propagation study of rock based on uniaxial compressive test——a case study of schistose rock[J]. Chinese Journal of Rock Mechanics and Engineering，2011，30(9)：1 772–1 781.(in Chinese))
[32] 李忠辉，王恩元，郑安琪，等. 煤层瓦斯抽采钻孔变形破坏测试技术及其应用研究[J]. 煤炭科学技术，2020，48(10)：37–44.(LI Zhonghui，WANG Enyuan，ZHENG Anqi，et al. Research on testing technology of deformation and failure of boreholes in coal seam gas drainage and its application[J]. Coal Science and Technology，2020，48(10)：37–44.(in Chinese))
[33] 潘红宇，冯高远，纪翔，等. 加载速率影响下含雁行裂纹–钻孔煤体变形破坏特征研究[J]. 岩石力学与工程学报，2024，43(3)：573–586.(PAN Hongyu，FENG Gaoyuan，JI Xiang，et al. Study on deformation and failure characteristics of coal containing echelon crack-boreholes under the influence of loading rates[J]. Chinese Journal of Rock Mechanics and Engineering，2024，43(3)：573–586.(in Chinese))