岩体压力型锚杆灌浆体受压承载力计算

doi:10.3724/1000-6915.jrme.2025.0739

Abstract
Figure/Table
References (0)
Related Citation (15)

Download: PDF (987 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract The lateral confinement of the rock mass can significantly enhance the grout compressive bearing capacity of compression anchors. However, this bearing capacity is difficult to quantify. Current specifications adopt empirical calculation methods, which tend to result in large deviations in calculation results. To address the aforementioned challenges in quantitative calculation, this paper develops a mechanical model that considers limited cracking depth of the rock mass surrounding the grout, derives a method for calculating the grout compressive bearing capacity, and systematically analyzes the influences of relevant parameters. The results indicate that when limited cracking is allowed in the surrounding rock mass, the axial stress sustained by the grouted body increases significantly. This stress shows a marked increase with the propagation of crack depth, ultimately reaching the compressive bearing capacity at the critical cracking depth. Under identical crack depths in the rock mass, the axial stress sustained by the grouted body significantly increases with the elastic modulus of the grout and the tensile strength of the rock mass, while it decreases notably with an increase in the Poisson?s ratio of the grout and the elastic modulus of the rock mass. In contrast, the radius of the reinforcing bar and the Poisson?s ratio of the rock mass have negligible effects on the axial stress of the grouted body. To verify the method proposed in this study, field tests were conducted in moderately weathered granite. Through comparative analysis, the calculated results from this study are slightly larger than the measured values, but the overall trend is consistent with a high degree of agreement, which verifies the validity of the proposed method. This method provides valuable references for further theoretical research and engineering design related to the grout compressive bearing capacity of compression anchors.

Key words： rock mechanics lateral confinement compression anchor grouted body compressive bearing capacity fracture depth coefficient

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	TU Bingxiong1*
	ZHENG Jinhuo2
	ZHANG Xiaoshuo1
	LI Zhiwei3

Cite this article:

TU Bingxiong1*,ZHENG Jinhuo2,ZHANG Xiaoshuo1, et al. Calculation of grout compressive bearing capacity for compression anchor in rock mass[J]. , 2026, 45(3): 684-694.

URL:

https://rockmech.whrsm.ac.cn/EN/10.3724/1000-6915.jrme.2025.0739 OR https://rockmech.whrsm.ac.cn/EN/Y2026/V45/I3/684

[1] 王贵和，吕建国，贾苍琴，等. 压力分散型抗浮锚杆承载特性分析[J]. 建筑结构学报，2007，(增1)：252–256.(WANG Guihe，LÜ Jianguo，JIA Cangqin，et al. Characteristic analysis on compression-dispersive anti-float anchor[J]. Journal of Building Structures，2007，(Supp.1)：252–256.(in Chinese))
[2] 谭光宇，蒋耀华，方伟明，等. 全长压力型后张预应力抗浮锚杆结构设计研究[J]. 建筑结构，2021，51(21)：7–10.(TAN Guangyu，JIANG Yaohua，FANG Weiming，et al. Study on structural design of full-length compression post-tensioned prestressed anti-floating anchor[J]. Building Structure，2021，51(21)：7–10.(in Chinese))
[3] 王锐松，郭成超，林沛元，等. 富水粉土基坑装配式可回收支护开挖响应分析[J]. 岩土力学，2023，44(3)：843–853.(WANG Ruisong，GUO Chengchao，LIN Peiyuan，et al. Excavation response analysis of prefabricated recyclable support structure for water-rich silt foundation pit[J]. Rock and Soil Mechanics，2023，44(3)：843–853.(in Chinese))
[4] 赵启嘉，刘正根. 可回收锚索在基坑支护工程中的技术研究及应用探讨[J]. 岩土工程学报，2012，34(增1)：480–483.(ZHAO Qijia，LIU Zhenggen. Application of recycling anchor cables in support of excavations[J]. Chinese Journal of Geotechnical Engineering，2012，34(Supp.1)：480–483.(in Chinese))
[5] 中华人民共和国国家标准编写组. GB 50086—2015 岩土锚杆与喷射混凝土支护工程技术规范[S]. 北京：中国计划出版社，2015.(The National Standards Compilation Group of People?s Republic of China. GB 50086—2015 Technical code for engineering of ground anchorages and shotcrete support[S]. Beijing：China Planning Press，2015.(in Chinese))
[6] 中华人民共和国行业标准编写组. YB/T 4659—2018抗浮锚杆技术规程[S]. 北京：冶金工业出版社，2018.(The Professional Standards Compilation Group of People?s Republic of China. YB/T 4659—2018 Technical specification for anti-floating anchor[S]. Beijing：Metallurgical Industry Press，2018.(in Chinese))
[7] 中华人民共和国行业标准编写组. T/CECS 999—2022 可回收锚杆应用技术规程[S]. 北京：中国计划出版社，2022.(The Professional Standards Compilation Group of People?s Republic of China. T/CECS 999—2022 Technical specification for application of removable anchors[S]. Beijing：China Planning Press，2022.(in Chinese))
[8] 尤春安. 压力型锚索锚固段的受力分析[J]. 岩土工程学报，2004，26(6)：828–831.(YOU Chun?an. Mechanical analysis on anchorage segment of pressure-type cable[J]. Chinese Journal of Geotechnical Engineering，2004，26(6)：828–831.(in Chinese))
[9] REN L，ZHU B，LI J. Influence of borehole deviation on pressure-type anchor cables：characteristics of stress distribution and transmission[J]. International Journal of Civil Engineering，2025，23(2)：327–343.
[10] 卢黎，张永兴，吴曙光. 压力型锚杆锚固段的应力分布规律研究[J]. 岩土力学，2008，29(6)：1 517–1 520.(LU Li，ZHANG Yongxing，WU Shuguang. Distribution of stresses on bonded length of compression type rock bolt[J]. Rock and Soil Mechanics，2008，29(6)：1 517–1 520.(in Chinese))
[11] 易梅辉，高文华，向德强，等. 基于流变理论的压力型锚杆锚固段荷载传递机制研究[J]. 应用力学学报，2020，37(4)：1 556–1 563.(YI Meihui，GAO Wenhua，XIANG Deqiang，et al. Study on load transfer mechanism of pressure anchor anchorage section based on rheological theory [J]. Chinese Journal of Applied Mechanics，2020，37(4)：1 556–1 563.(in Chinese))
[12] 张爱民，胡毅夫. 压力型锚杆锚固段锚固效应特性分析[J]. 岩土工程学报，2009，31(2)：271–275.(ZHANG Aimin，HU Yifu. Anchoring effect of pressure-type anchor rods on anchored section[J]. Chinese Journal of Geotechnical Engineering，2009，31(2)：271–275.(in Chinese))
[13] 贺建清，胡成兵，张建超. 基于Mindlin解的压力型锚杆锚固段的受力分析[J]. 水文地质工程地质，2012，39(1)：47–52.(HE Jianqing，HU Chengbing，ZHANG Jianchao. Mechanical analysis of anchorage segment of pressure-type cable based on Mindlin solution[J]. Hydrogeology and Engineering Geology，2012，39(1)：47–52.(in Chinese))
[14] 张永兴，卢黎，饶枭宇，等. 压力型锚杆力学性能模型试验研究[J]. 岩土力学，2010，31(7)：2 045–2 050.(ZHANG Yongxing，LU Li，RAO Xiaoyu，et al. Model test research on mechanical behavior of compression type rock bolt[J]. Rock and Soil Mechanics，2010，31(7)：2 045–2 050.(in Chinese))
[15] 芮瑞，夏元友，顾金才，等. 压力分散型锚索锚固段受力特性试验分析[J]. 岩土工程学报，2012，34(5)：917–923.(RUI Rui，XIA Yuanyou，GU Jincai，et al. Field test and mechanical analysis of anchorage segment of pressure-dispersion anchors[J]. Chinese Journal of Geotechnical Engineering，2012，34(5)：917–923.(in Chinese))
[16] LEI X，WANG B，LI N，et al. Study on dynamic response of pressure type anchor and lattice beam system under seismic loadings[J]. Geotechnical and Geological Engineering，2020，38(6)：6 057–6 067.
[17] KIM N K. Performance of tension and compression anchors in weathered soil[J]. Journal of Geotechnical and Geoenvironmental Engineering，2003，129(12)：1 138–1 150.
[18] 冉孟吉，涂兵雄，刘超，等. 压力型锚杆灌浆体受压承载力的计算模型与方法[J]. 华侨大学学报：自然科学版，2021，42(6)：748–757.(RAN Mengji，TU Bingxiong，LIU Chao，et al. Calculation model and method of compressive capacity of grout body for compression-type anchor[J]. Journal of Huaqiao University：Natural Science，2021，42(6)：748–757.(in Chinese))
[19] 徐芝纶. 弹性力学简明教程[M]. 北京：高等教育出版社，2020：74–76.(XU Zhilun. A concise course in elastic mechanics[M]. Beijing：Higher Education Press，2020：74–76.(in Chinese))
[20] 孙训方，方孝淑，关来泰. 材料力学[M]. 北京：高等教育出版社，2019：20–21.(SUN Xunfang，FANG Xiaoshu，GUAN Laitai. Mechanics of materials[M]. Beijing：Higher Education Press，2019：20–21.(in Chinese))
[21] 中华人民共和国国家标准编写组. GB/T 50010—2010混凝土结构设计标准[S]. 北京：中国建筑工业出版社，2010.(The National Standards Compilation Group of People?s Republic of China. GB/T 50010—2010 Code for design of concrete structures[S]. Beijing：China Architecture and Building Press，2010.(in Chinese))
[22] 涂兵雄，林振德，陈云彬，等. 一种检测可回收锚杆端部灌浆体受压承载力的试验方法[P]. 中国：CN202110033560.7，2022–07–01. (TU Bingxiong，LIN Zhende，CHEN Yunbin，et al. A test method for detecting the compressive bearing capacity of grout body at the end of recyclable anchor bolts[P]. China：CN202110033560.7，2022–07–01. (in Chinese))