金川全尾砂–棒磨砂混合充填料胶砂强度与料浆流变特性研究

doi:10.13722/j.cnki.jrme.2014.s2.075

摘要
图/表
参考文献(19)
相关文章 (0)

全文: PDF (1330 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要针对金川矿山棒磨砂充填料严重不足，开展全尾砂–棒磨砂混合充填料的胶砂试验研究。通过不同配比和料浆浓度的全尾砂–棒磨砂混合充填料的胶砂强度试验和料浆流变特性参数测试，获得充填体试块强度与混合料的配合比、平均粒径以及不均匀性系数之间的关系，针对金川下向进路胶结充填法采矿，确定了满足充填体强度要求的全尾砂–棒磨砂的合理配比为3∶7。研究表明，混合充填料的7和28 d充填体强度和砂浆泌水率与沉降损失率，均优于纯棒磨砂充填料。该研究结果为金川矿山全尾砂工业化应用提供技术支撑，为金川全尾砂废弃物的资源化利用和环境保护奠定了基础。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	杨志强1
	2
	高谦1
	王永前2
	陈得信2
	把多恒2

关键词 ：采矿工程；全尾砂&ndash, 棒磨砂；混合充填料；合理配比；抗压强度

Abstract：The research on mixed filling materials including unclassified tailings and rod milling sand was conducted due to the serious lack of rod mill sand in Jinchuan mine. Based on the experiments of filling body strength and rheological properties for different ratios of mixed filling mortar with unclassified tailings-rod milling sand，revealed the relationship between filling body strength and the ratios，average particle size and uniformity coefficient and determined the reasonable ratio of Unclassified Tailings and Rod Milling sand was 3∶7 which apply to underhand drift cut-and-fill method in Jinchuan mine. The research shows that the compressive strength of 7 d and 28 d bleeding and sedimentation rate were precede rod milling sands. This research achievement provided important technical support to industrialized application of unclassified tailings in Jinchuan mine and laid the foundation of the utilization of waste resources and environmental protection.

Key words： mining engineering unclassified tailings-rod milling sand mixed filling material ration compressive strength

引用本文:

杨志强1，2，高谦1，王永前2，陈得信2，把多恒2. 金川全尾砂–棒磨砂混合充填料胶砂强度与料浆流变特性研究[J]. 岩石力学与工程学报, 2014, 33(S2): 3985-3991.
YANG Zhiqiang1，2，GAO Qian1，WANG Yongqian2，CHEN Dexin2，BA Duoheng2. RESEARCH ON FILLING BODY STRENGTH AND RHEOLOGICAL PROPERTIES OF MIXED FILLING MORTAR WITH UNCLASSIFIED TAILINGS AND ROD MILLING SAND IN JINCHUAN MINE. , 2014, 33(S2): 3985-3991.

链接本文:

https://rockmech.whrsm.ac.cn/CN/10.13722/j.cnki.jrme.2014.s2.075 或 https://rockmech.whrsm.ac.cn/CN/Y2014/V33/IS2/3985

[1] 王洪江，吴爱祥，陈进，等. 全尾砂–水淬渣膏状物料可泵性指标优化[J]. 采矿技术，2007，7(3)：15–21.(WANG Hongjiang，WU Aixiang，CHEN Jin，et al. The pumpability index optimization of paste material mixed by full tailling and slag[J]. Mining Technology，2007，7(3)：15–21.(in Chinese))

[2] 王贤来，姚维信，王虎，等. 矿山废石全尾砂充填研究现状与发展趋势[J]. 中国矿业，2011，20(9)：76–79.((WANG Xianlai，YAO Weixin，WANG Hu，et al. The directions of R&R on backill with waste rock and total taillings in underground mine[J]. China Mining Magazine，2011，20(9)：76–79.(in Chinese))

[3] 赵传卿，胡乃联. 焦家金矿充填物料的颗粒级配优选研究[J]. 矿冶，2008，17(2)：17–19.(ZHAO Chuanqing，HU Nailian. Study on granula grade ratio optizatize in the fill material for Jiaojia gold mine[J]. Mining Metallurgy，2008，17(2)：17–19.(in Chinese))

[4] 兰凤，郄志红，邢志红，等. 砂的颗粒组成对砂浆性能影响的试验研究[J]. 混凝土，2012，(12)：87–89.(LAN Feng，QIE Zhihong，XING Zhihong，et al. Experimental study on the in fluences of grain composition of sand on mortar performance[J]. Concrete，2012，(12)：87–89.(in Chinese))

[5] 孙恒虎，段鸿杰，刘华生. 应用确定有效细粒群的最佳配比[J]. 北京科技大学学报，2003，25(6)：504–506.(SUN Henghu，DUAN Hongjie，LIU Huasheng. Application of to optimum ratio determination of effective silt particles[J]. Journal of University of Science and Teehnology Beijing，2003，25(6)：504–506.(in Chinese))

[6] 孙恒虎，段鸿杰，刘华生. 应用RRSB方程模数实现尾砂级配优化的研究[J]. 有色金属，2004，56(1)：92–95.(SUN Henghu，DUAN Hongjie，LIU Huasheng. Adoption of RRSB distribution equation modulus in back tailings size composition optimization[J]. Nonferrous Metals，2004，56(1)：92–95.(in Chinese))

[7] 邹辉，李向阳，钟永明. 全尾砂–水淬渣膏体性能参数测试方法研究[J]. 矿业工程，2007，5(1)：31–34.(ZOU Hui，LI Xiangyang，ZHONG Yongming. Research o method of parameter measure of unclassified tailings-slag paste[J]. Mining Engineering，2007，5(1)：31–34.(in Chinese))

[8] 马昆林，龙广成，谢友均，等. 水泥–粉煤灰–石灰石粉复合浆体的流变性能[J]. 硅酸盐学报，2013，41(5)：582–596.(MA Kunlin，LONG Guangcheng，XIE Youjun，et al. Rheological properties of compound pastes with cement-fly ash-limestone powder[J]. Journal of the Chinese Ceramic Society，2013，41(5)：582–596.(in Chinese))

[9] 武拴军，辜大志，张海军. 降低膏体料浆沿程阻力损失的试验研究[J]. 采矿技术，2011，11(4)：37–38.(WU Shuanjun，GU Dazhi，ZHANG Haijun. Experimental study on reduce the frictional resistance of the paste slurry[J]. Mining Technology，2011，11(4)：37–38.(in Chinese))

[10] 唐修生，蔡跃波，温金保，等. 磨细矿渣复合浆体流变参数与流动度的相关性[J]. 硅酸盐学报，2014，42(5)：648–652.(TANG Xiusheng，CAI Yuebo，WEN Jinbao，et al. Correlation between slump flow and rheological parameters of compound pastes with high volume of ground slag[J]. Journal of the Chinese Ceramic Society，2014，42(5)：648–652.(in Chinese))

[11] 张海亚，张斌. 萘系和聚羧酸系高效减水剂对混凝土性能的影响比较[J]. 混凝土与水泥制品，2011，(7)：10–12.(ZHANG Haiya，ZHANG Bin. A comparison between the effects of naphthalene series superplasticizer and polycarboxylate series super-plasticizer on the concrete¢s performances[J]. China Concrete and Cement Products，2011，(7)：10–12.(in Chinese))

[12] 吕亚夫. 浅析高效减水剂与水泥间的适应性[J]. 建筑科学，2013，(29)：250–251.(LU Yafu. Study on the adaptability between superplasticize and cement[J]. Construction Science，2013，(29)：250–251.(in Chinese))

[13] 杨志强，王永前，高谦，等. 全尾砂–棒磨砂混合充填料浆的优化配比试验研究[J]. 中国矿山工程，2013，42(6)：1–5.(YANG Zhiqiang，WANG Yongqian，GAO Qian，et al. Experimental research on the optimal ratio of compound filling materials of whole tailings and rod milling sand[J]. China Mine Engineering，2013，42(6)：1–5.(in Chinese))

[14] 龙秀才，陈发吉. 磷石膏充填材料及其配比试验研究[J]. 化工矿物与加工，2011，(4)：22–25.(LONG Xiucai，CHEN Faji. Ratio optimization of phosphogypsum filling material and auxiliary materials[J]. Industrial Minerals and Processing，2011，(4)：22–25.(in Chinese))

[15] 韩斌，吴爱祥，王贻明，等. 低强度粗骨料超细全尾砂自流胶结充填配合比优化及应用[J]. 中南大学学报，2013，43(6)：2 357– 2 362.(HAN Bin，WU Aixiang，WANG Yiming，et al. Optimization and application of cemented hydraulic fill(CHF) with low strength aggregate and extra fine grain full tailings[J]. Journal of Central South University，2013，43(6)：2 357–2 362.(in Chinese))

[16] 王新民，徐东升. 胶结充填料优化配比研究及强度预测[J]. 矿业快报，2006，(12)：20–23.(WANG Xinmin，XU Dongsheng. Research on Optimization Proportioning of Cemented Filling Material and Strength Forecasting[J]. Express Information of Mining Industry. 2006，(12)：20–23.(in Chinese))

[17] 常庆粮，周华强，秦剑云，等. 膏体充填材料配比的神经网络预测研究[J]. 采矿与安全工程学报，2009，26(1)：74–77.(CHANG Qingliang，ZHOU Huaqiang，QING Jianyun，et al. Sing artificial neural network model to determine the prescription of paste filling materials[J]. Journal of Mining and Safety Engineering，2009，26(1)：74–77.(in Chinese))

[18] 张钦礼，李谢平，杨伟. 基于BP网络的某矿山充填料浆配比优化[J]. 中南大学学报，2013，44(7)：2 867–2 873.(ZHANG Qinli，LI Xieping，YANG Wei. Optimization of filling slurry ratio in a mine based on back-propagation neural network[J]. Journal of Central South University，2013，44(7)：2 867–2 873.(in Chinese))

[19] 张磊，乔登攀，程纬华，等. 金川粗骨料级配与强度分析[J]. 矿冶，2012，21(3)：12–15.(ZHANG Lei，QIAO Dengpan，CHENG Weihua，et al. Analysis on gradation and intensity of coarse aggregate of JNMC[J]. Mining and Metallurgy，2012，21(3)：12–15.(in Chinese))