卸载速率对卸载诱发页岩滑移行为影响的试验研究

doi:10.13722/j.cnki.jrme.2022.1114

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (1746 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要为研究卸载速率对卸载诱发页岩滑移行为的影响，利用MTS815岩石力学试验系统对接近临界应力状态下的含节理页岩进行恒轴压分级卸围压的诱发滑移试验，卸载速率分别为0.01，0.1，1和10 MPa/min。试验结果表明：(1) 锯切节理面在滑移试验后表面的微凸体平均高度出现降低且粗糙度变大。随着卸载速率的增加，试样的表面粗糙度系数(JRC)分别上升了22.68 %，44.82%，38.49%和49.89%。(2) 试样滑移速度随着围压卸载速率的增加而增加，且在相同卸载速率下试样的准静态滑移平均速度比蠕变滑移平均速度大2个数量级。蠕变滑移平均速度分别为4.87×10－6，2.52×10－5，3.99×10－4和3.29×10－3 mm/s，相应的准静态滑移平均速度分别为7.39×10－4，5.98×10－3，2.8×10－2 和1.2×10－1 mm/s。(3) 试样在0.1 MPa/min卸载速率下发生滑移时的围压卸载量最小且摩擦强化效果最弱。在0.01 MPa/min卸载速率下试样的摩擦强度在长期的蠕变滑移中得到强化，在动态滑移中表现出摩擦弱化特征。试样在1和10 MPa/min的卸载速率下在较短时间内发生滑移，且试样在动态滑移中表现出摩擦强化特征。(4) 根据试验结果分析卸载速率在0.1～1 MPa/min之间存在临界值，当试样在临界卸载速率下发生滑移时，围压卸载量最小，使得节理面上积聚的应变能较小，能量在滑移释放时主要作用于微凸体以突破互锁效应，因此滑移释放的能量最小且产生最小的剪切位移，这对岩体工程的安全保障具有重要意义。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	季浩奇
	刘日成
	蔚立元
	李树忱
	王晓琳

关键词 ：岩石力学, 卸载诱发滑移, 卸载速率, 节理粗糙度, 摩擦因数

Abstract：To investigate the effect of the unloading rate on the unloading-induced slip mechanism of shale，the slip start-up of jointed shales is triggered by stepwise-unloading confining pressure with constant axial stress using MTS815 loading system，wherein the unloading rates are 0.01，0.1，1 and 10 MPa/min respectively. The results show that：(1) The asperity altitude of the saw-cut joint decreases and the roughness increases due to slip deformation. With the increase of the unloading rate，the joint roughness coefficient(JRC) of saw-cut morphology increases by 22.68%，44.82%，38.49% and 49.89%，respectively. (2) The slip velocity increases with the elevation of the unloading rate，and the average velocity of quasi-static slip is two orders of magnitude higher than that of creep slip at the same unloading rate. The creep slip average velocities are 4.87×10－6，2.52×10－5，3.99×10－4 and 3.29×10－3 mm/s，respectively. The corresponding average quasi-static slip velocities are 7.39×10－4，5.98×10－3，2.8×10－2 and 1.2×10－1 mm/s，respectively. (3) The unloading amount of confining pressure is the smallest and the friction strengthening effect is the weakest under 0.1 MPa/min. Under 0.01 MPa/min，the friction strength of the sample is well enhanced in the long-term creep slip，and the friction strength is weakened in the dynamic slip. At the unloading rate of 1 and 10 MPa/min，the sample will slip in a short time，and the friction strength is enhanced in the dynamic slip. (4) There is a critical unloading rate between 0.1–1 MPa/min，and the unloading amount of confining pressure is the smallest when the sample slips at the critical unloading rate. It presents that the strain energy accumulated on the joint plane is smaller and the energy mainly acts on the micro-convexities to break the interlocking during the slip，so the energy released after the slip is the smallest and produces the minimum shear displacement，which is of great significance for the safety of rock mass engineering.

Key words： rock mechanics unloading-induced slip unloading rate surface roughness friction coefficient

引用本文:

季浩奇，刘日成，蔚立元，李树忱，王晓琳. 卸载速率对卸载诱发页岩滑移行为影响的试验研究[J]. 岩石力学与工程学报, 2023, 42(8): 1959-1972.
JI Haoqi，LIU Richeng，YU Liyuan，LI Shuchen，WANG Xiaolin. Influence of unloading rate on mechanical behaviors of shales during#br# unloading-induced slip processes. , 2023, 42(8): 1959-1972.

链接本文:

http://rockmech.whrsm.ac.cn/CN/10.13722/j.cnki.jrme.2022.1114 或 http://rockmech.whrsm.ac.cn/CN/Y2023/V42/I8/1959

[9]	JI Y L，WU W，ZHAO Z H. Unloading-induced rock fracture activation and maximum seismic moment prediction[J]. Engineering Geology，2019，262：105352.
[27]	MYERS N. Characterization of surface roughness[J]. Elsevier，1962，5(3)：182-189.
[2]	FOULGER G R，WILSON M P，GLUYAS J G，et al. Global review of human-induced earthquakes[J]. Earth-Science Reviews，2017，178：438-514.
[20]	BRADY B H，BROWN E T. Rock mechanics for underground mining[M]. [S. l.]：Springer Science and Business Media，1993.
[4]	赵同彬，程康康，魏平，等. 含弱面岩石滑移破坏及锚固控制试验研究[J]. 采矿与安全工程学报，2017，34(6)：1 081-1 087.(ZHAO Tongbin，CHENG Kangkang，WEI Ping，et al. Study on slip failure of rock with weak plane and anchorage control mechanism[J]. Journal of Mining and Safety Engineering，2017，34(6)：1 081-1 087.(in Chinese))
[5]	WANG L，KWIATEK G，RYBACKI E，et al. Injection-induced seismic moment release and laboratory fault slip：Implications for fluid-induced seismicity[J]. Geophysical Research Letters，2020，47(22)：1-11.
[23]	ELLSWORTH W L. Injection-induced earthquakes[J]. Science，2013，341(6142)：1225942.
[7]	张重远，何满潮，陶志刚，等. 发震断层震前应力降现象及其机制探讨[J]. 岩石力学与工程学报，2021，40(5)：916-927.(ZHANG Chongyuan，HE Manchao，TAO Zhigang，et al. Discussion on stress drop mechanisms of seismogenic faults before earthquakes[J]. Chinese Journal of Rock Mechanics and Engineering，2021，40(5)：916-927.(in Chinese))
[11]	MENG F，WONG L N Y，ZHOU H，et al. Shear rate effects on the post-peak shear behavior and acoustic emission characteristics of artificially split granite joints[J]. Rock Mechanics and Rock Engineering，2019，52：2 489.
[14]	何满潮，赵菲，杜帅，等. 不同卸载速率下岩爆破坏特征试验分析[J]. 岩土力学，2014，35(10)：2 737-2 747.(HE Manchao，ZHAO Fei，DU Shuai，et al. Rockburst characteristics based on experimental tests under different unloading rates[J]. Rock and Soil Mechanics，2014，35(10)：2 737-2 747.(in Chinese))
[16]	陈卫忠，吕森鹏，郭小红，等. 基于能量原理的卸围压试验与岩爆判据研究[J]. 岩石力学与工程学报，2009，28(8)：1 530-1 540. (CHEN Weizhong，LU Senpeng，GUO Xiaohong，et al. Research on unloading confining pressure tests and rockburst criterion based on energy theory[J]. Chinese Journal of Rock Mechanics and Engineering，2009，28(8)：1 530-1 540.(in Chinese))
[18]	HAN Y，MA H，YANG C. The mechanical behavior of rock salt under different confining pressure unloading rates during compressed air energy storage(CAES)[J]. Journal of Petroleum Science and Engineering，2021，196：107676.
[25]	班力壬，戚承志，李晓照，等. 考虑真实接触微凸体的岩石节理三维粗糙度指标[J]. 煤炭学报，2020，45(12)：4 052-4 061.(BAN Liren，QI Chengzhi，LI Xiaozhao，et al. A 3D quantified surface description for rock joint based on the real contact asperities[J]. Journal of China Coal Society，2020，45(12)：4 052-4 061.(in Chinese))
[29]	曹秋菊，王金安. 断裂岩石粗糙性与岩体抗剪强度和机制的实验研究[J]. 中国矿业，2012，21(5)：107-111. (CAO Qiuju，WANG Jin?an. Experimental study on roughness and long shear strength of fracture rock[J]. China Mining Magazine，2012，21(5)：107-111.(in Chinese))
[32]	MARONE C. Laboratory-derived friction laws and their application to seismic faulting[J]. Annual Review of Earth and Planetary Sciences，1998，26(1)：643-696.
[3]	李志华，窦林名，陆振裕，等. 采动诱发断层滑移失稳的研究[J]. 采矿与安全工程学报，2010，27(4)：499-504.(LI Zhihua，DOU Linming，LU Zhenyu，et al. Study of the fault slide destabilization induced by coal mining[J]. Journal of Mining and Safety Engineering，2010，27(4)：499-504.(in Chinese))
[12]	李海波，张天航，邵蔚，等. 三轴压缩情况下岩石变形特征的滑移型裂纹模拟[J]. 岩石力学与工程学报，2005，24(17)：3 119-3 124. (LI Haibo，ZHANG Tianhang，SHAO Wei，et al. Simulation of deformation behavior of rock material under triaxial compression based on sliding crack model[J]. Chinese Journal of Rock Mechanics and Engineering，2005，24(17)：3 119-3 124.(in Chinese))
[21]	KOHLI A H，ZOBACK M D. Frictional properties of shale reservoir rocks[J]. Journal of Geophysical Research，2013，118(9)：5 109-5 125.
[30]	INDRARATNA B，HAQUE A. Experimental study of shear behavior of rock joints under constant normal stiffness conditions[J]. International Journal of Rock Mechanics and Mining Sciences，1997，34(3)：141-155.
[1]	WU W，ZHAO Z H，DUAN K，et al. Unloading-induced instability of a simulated granular fault and implications for excavation-induced seismicity[J]. Tunnelling and Underground Space Technology，2017，63：154-161.
[8]	宋义敏，马少鹏，杨小彬，等. 断层黏滑动态变形过程的实验研究[J]. 地球物理学报，2012，55(1)：171-179.(SONG Yimin，MA Shaopeng，YANG Xiaobin，et al. Experimental study on the dynamic displacement evolution of fault in stick-slip process[J]. Chinese Journal of Geophysics，2012，55(1)：171-179.(in Chinese))
[10]	WU W，ZOU Y，LI X，et al. An unload-induced direct-shear model for granular gouge friction in rock discontinuities[J]. Review of Scientific Instruments，2014，85(9)：093902.
[6]	赵扬锋，荆刚，樊艺，等. 断层黏滑失稳过程微震与电荷信号时频特征研究[J]. 岩石力学与工程学报，2020，39(7)：1 385-1 395. (ZHAO Yangfeng，JING Gang，FAN Yi，et al. Experimental study on the microseism and charge signal time-frequency characteristics in the process of fault stick-slip instability[J]. Chinese Journal of Rock Mechanics and Engineering，2020，39(7)：1 385-1 395.(in Chinese))
[15]	张凯，周辉，潘鹏志，等. 不同卸荷速率下岩石强度特性研究[J]. 岩土力学，2010，31(7)：2 072-2 078.(ZHANG Kai，ZHOU Hui，PAN Pengzhi，et al. Characteristics of strength of rocks under different unloading rates[J]. Rock and Soil Mechanics，2010，31(7)：2 072-2 078.(in Chinese))
[17]	刘婕，张黎明，丛宇，等. 真三轴应力路径花岗岩卸荷破坏力学特性研究[J]. 岩土力学，2021，42(8)：2 069-2 077.(LIU Jie，ZHANG Liming，CONG Yu，et al Research on the mechanical characteristics of granite failure process under true triaxial stress path[J]. Rock and Soil Mechanics，2021，42(8)：2 069-2 077.(in Chinese))
[19]	XU H，FENG X T，YANG C X，et al. Influence of initial stresses and unloading rates on the deformation and failure mechanism of Jinping marble under true triaxial compression[J]. International Journal of Rock Mechanics and Mining Sciences，2019，117：90-104.
[24]	李宏哲，夏才初，王晓东，等. 含节理大理岩变形和强度特性的试验研究[J]. 岩石力学与工程学报，2008，27(10)：2 118-2 123.(LI Hongzhe，XIA Caichu，WANG Xiaodong，et al. Experimental study on deformation and strength properties of jointed marble specimens[J]. Chinese Journal of Rock Mechanics and Engineering，2008，27(10)：2 118-2 123.(in Chinese))
[26]	ISRM. Rock characterization，testing and monitoring-ISRM suggested methods[C]// Suggested Methods for the Quantitative Description of Discontinuities in Rock Masses. Pergamon，Oxford：[s. n. ]，1981：3-52.
[28]	TSE R，CRUDEN D. Estimating joint roughness coefficients[J]. International Journal of Rock Mechanics and Mining Sciences，1979，16(5)：303-307.
[33]	秦忠诚，刘贝贝，陶雄兵. 采掘诱发断层冲击地压的能量判据及监测[J]. 煤炭技术，2016，35(1)：105-108.(QIN Zhongcheng，LIU Beibei，TAO Xiongbing. Energy criterion and monitoring of rock burst induced by mining[J]. Coal Technology，2016，35(1)：105-108.(in Chinese))
[13]	YE Z，GHASSEMI A. Heterogeneous fracture slip and aseismic-seismic transition in a triaxial injection test[J]. Geophysical Research Letters，2020，47(14)：e2020GL087739.
[22]	YE Z，GHASSEMI A. Injection-induced shear slip and permeability enhancement in granite fractures[J]. Journal of Geophysical Research：Solid Earth，2018，123：9 009-9 032.
[31]	BRACE F P，TABOR D. The friction and lubrication of solids[J]. Oxford：Clarendon Press，1951，19(7)：428.