考虑页岩顶板各向异性脆性破坏的回采巷道数值模拟标定研究

doi:10.3724/1000-6915.jrme.2025.0878

Abstract
Figure/Table
References (0)
Related Citation (15)

Download: PDF (3264 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract Laminated shale is a common roof type in coal mine roadways, where its significant anisotropic brittle characteristics often induce asymmetric large deformation and roof fall accidents. However, existing numerical simulation studies frequently overlook the influence of bedding plane orientation and lack calibration against in-situ measurements, making it difficult to accurately reveal the mechanical properties and deformation patterns of shale roofs. Based on in-situ measurements from five typical U.S. coal seams (e.g., Lower Kittanning and Pittsburgh), this paper proposes a systematic model calibration workflow combining theoretical analysis and numerical simulation. The procedure includes: calibration of vertical and horizontal stresses, calibration of roof sag and cable bolt loads, and verification of anisotropic brittle failure characteristics. Subsequently, a FLAC3D roadway numerical model incorporating an anisotropic brittle failure criterion was established, realizing the coupled characterization of anisotropy in shale strength and elastic modulus, cohesion-weakening friction-strengthening behavior, and dilatancy features. Furthermore, roadway models covering four typical mining geological conditions were constructed: highly laminated shale roofs, high horizontal stress, deep three-pillar systems, and single-pillar systems. The simulated ranges of vertical stress (5–48 MPa) and horizontal stress (6–42 MPa) effectively cover the geo-stress conditions of most U.S. coal seams. Compared with traditional methods, the calibrated model more accurately characterizes strata behaviors, such as stress distribution, roof sag, cable loads, and failure patterns. It reveals the asymmetric failure mechanism of laminated roofs and clarifies the risk of roof cutting and large deformation in single-pillar systems. This study deepens the understanding of the anisotropic brittle failure mechanism of laminated shale at the entry scale and provides a reliable numerical analysis framework for the stability analysis of longwall tailgates/headgates under complex geological conditions.

Key words： mining engineering shale roof anisotropic brittle failure model calibration longwall tailgates/ headgates numerical simulation

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	WU Fan1
	ZHAO Gaobo2
	3*
	GUO Wenbing1
	4
	LI Longxiang5

Cite this article:

WU Fan1,ZHAO Gaobo2,3*, et al. Field-based calibrated numerical modeling of longwall tailgates/headgates: anisotropic brittle failure characteristics in shale roofs[J]. , 2026, 45(7): 2185-2200.

URL:

https://rockmech.whrsm.ac.cn/EN/10.3724/1000-6915.jrme.2025.0878 OR https://rockmech.whrsm.ac.cn/EN/Y2026/V45/I7/2185

[1] 康红普，姜鹏飞，黄炳香，等. 煤矿千米深井巷道围岩支护–改性–卸压协同控制技术[J]. 煤炭学报，2020，45(3)：845–864.(KANG Hongpu，JIANG Pengfei，HUANG Bingxiang，et al. Roadway strata control technology by means of bolting-modification-destressing in synergy in 1 000 m deep coal mines[J]. Journal of China Coal Society，2020，45(3)：845–864.(in Chinese))
[2] 谢和平，高峰，鞠杨，等. 深地科学领域的若干颠覆性技术构想和研究方向[J]. 工程科学与技术，2017，49(1)：1–8.(XIE Heping，GAO Feng，JU Yang，et al. Novel idea and disruptive technologies for the exploration and research of deep earth[J]. Advanced Engineering Sciences，2017，49(1)：1–8.(in Chinese))
[3] ABOUSLEIMAN R，WALTON G，SINHA S. Understanding roof deformation mechanics and parametric sensitivities of coal mine entries using the discrete element method[J]. International Journal of Mining Science and Technology，2020，30(1)：123–129.
[4] 邓华锋，王伟，李建林，等. 层状砂岩各向异性力学特性试验研究[J]. 岩石力学与工程学报，2018，37(1)：112–120.(DENG Huafeng，WANG Wei，LI Jianlin，et al. Experimental study on anisotropic characteristics of bedded sandstone[J]. Chinese Journal of Rock Mechanics and Engineering，2018，37(1)：112–120.(in Chinese))
[5] 袁亮，薛俊华，刘泉声，等. 煤矿深部岩巷围岩控制理论与支护技术[J]. 煤炭学报，2011，36(4)：535–543.(YUAN Liang，XUE Junhua，LIU Quansheng，et al. Surrounding rock stability control theory and support technique in deep rock roadway for coal mine[J]. Journal of China Coal Society，2011，36(4)：535–543.(in Chinese))
[6] MENG Y，JING H，LIU X，et al. Experimental and numerical investigation on the effect of bedding plane properties on fracture behaviour of sandy mudstone[J]. Theoretical and Applied Fracture Mechanics，2021，114：102 989.
[7] DU C，LIU Q，LEI Y，et al. Study the anisotropic behavior of layered surrounding rock based on 3D FDEM method[J]. Tunnelling and Underground Space Technology，2024，146：105 644.
[8] GAO F，STEAD D，KANG H. Numerical simulation of squeezing failure in a coal mine roadway due to mining-induced stresses[J]. Rock Mechanics and Rock Engineering，2015，48(4)：1 635–1 645.
[9] GAO F，STEAD D，KANG H，et al. Discrete element modelling of deformation and damage of a roadway driven along an unstable goaf— A case study[J]. International Journal of Coal Geology，2014，127：100–110.
[10] 梁运培，李其罡，黄旭超，等. 基于颗粒流的倾斜厚煤层坚硬顶板运动失稳规律及水力弱化参数研究[J]. 岩石力学与工程学报，2024，43(增1)：3 428–3 438.(LIANG Yunpei，LI Qigang，HUANG Xuchao，et al. Study on movement instability law and hydraulic weakening parameters of hard roof in inclined thick coal seam based on particle flow[J]. Chinese Journal of Rock Mechanics and Engineering，2024，43(Supp.1)：3 428–3 438.(in Chinese))
[11] 李昊擂，刘怀东，刘长友，等. 巷道顶板水力裂缝卸压的相场模型及数值模拟研究[J]. 中国矿业大学学报，2025，54(5)：971–983.(LI Haolei，LIU Huaidong，LIU Changyou，et al. Phase field model and numerical simulation study of hydraulic fractures for roadway roof pressure relief[J]. Journal of China University of Mining and Technology，2025，54(5)：971–983.(in Chinese))
[12] DENG P，LIU Q，HUANG X，et al. FDEM numerical modeling of failure mechanisms of anisotropic rock masses around deep tunnels[J]. Computers and Geotechnics，2022，142：104 535.
[13] CHONG Z，LI X，HOU P，et al. Numerical investigation of bedding plane parameters of transversely isotropic shale[J]. Rock Mechanics and Rock Engineering，2017，50(5)：1 183–1 204.
[14] JAEGER J C. Shear failure of anisotropic rocks[J]. Geological Magazine，1960，97(1)：65–72.
[15] HUDSON J A. Rock mechanics principles in engineering practice[M]. London：Butterworths，1989：1–72.
[16] 梁正召，唐春安，李厚祥，等. 单轴压缩下横观各向同性岩石破裂过程的数值模拟[J]. 岩土力学，2005，26(1)：57–62.(LIANG Zhengzhao，TANG Chun?an，LI Houxiang，et al. Numerical study on failure process of transversely isotropic rock subjected to uniaxial compression[J]. Rock and Soil Mechanics，2005，26(1)：57–62.(in Chinese))
[17] 张亚君，董彤，董宏晓，等. 一种适用于层状岩体的各向异性强度准则[J]. 岩石力学与工程学报，2024，43(10)：2 511–2 519. (ZHANG Yajun，DONG Tong，DONG Hongxiao，et al. An anisotropic strength criteria for layered rock mass[J]. Chinese Journal of Rock Mechanics and Engineering，2024，43(10)：2 511–2 519.(in Chinese))
[18] FAN Z D，REN L，XIE H P，et al. 3D anisotropy in shear failure of a typical shale[J]. Petroleum Science，2023，20(1)：212–229.
[19] 徐磊，任青文，杜小凯，等. 层状岩体各向异性弹塑性模型及其数值实现[J]. 地下空间与工程学报，2010，6(4)：763–769.(XU Lei，REN Qingwen，DU Xiaokai，et al. An anisotropic elastoplastic constitutive model for layered rock masses and its implementation[J]. Chinese Journal of Underground Space and Engineering，2010，6(4)：763–769.(in Chinese))
[20] HUANG S，ZHANG J，DING X，et al. Investigation of anisotropic strength criteria for layered rock mass[J]. Journal of Rock Mechanics and Geotechnical Engineering，2024，16(4)：1 289–1 304.
[21] KAISER P K，KIM B H. Characterization of strength of intact brittle rock considering confinement-dependent failure processes[J]. Rock Mechanics and Rock Engineering，2015，48(1)：107–119.
[22] 彭浩，韩玉，梁铭，等. 基于多源信息融合的隧道施工综合安全动态评估技术研究[J]. 岩土工程学报，2025，47(9)：1 893–1 902.(PENG Hao，HAN Yu，LIANG Ming，et al. Research on dynamic safety assessment technology for tunnel construction based on multi-source information fusion[J]. Chinese Journal of Geotechnical Engineering，2025，47(9)：1 893–1 902.(in Chinese))
[23] 刘力源，骆奕帆，王涛，等. 深部岩体变形模量数值反演计算方法及敏感性分析[J]. 煤炭学报，2024，49(增1)：154–166.(LIU Liyuan，LUO Yifan，WANG Tao，et al. Numerical inversion and sensitivity analysis of deformation modulus for deep rock mass[J]. Journal of China Coal Society，2024，49(Supp.1)：154–166.(in Chinese))
[24] GRUBERT E. Reserve reporting in the United States coal industry[J]. Energy Policy，2012，44：174–184.
[25] HÖÖK M，ALEKLETT K. Historical trends in American coal production and a possible future outlook[J]. International Journal of Coal Geology，2009，78(3)：201–216.
[26] ESTERHUIZEN G S，GEARHART D F，TULU I B. Analysis of monitored ground support and rock mass response in a longwall tailgate entry[J]. International Journal of Mining Science and Technology，2018，28(1)：43–51.
[27] ZHANG P，ESTERHUIZEN G，SEARS M，et al. Roof stability and support strategies associated with longwall-induced horizontal stress changes in belt entries[J]. Mining，Metallurgy and Exploration，2022，39(5)：1 873–1 885.
[28] KLEMETTI T M，VAN DYKE M A，TULU I B. Deep cover bleeder entry performance and support loading：A case study[J]. International Journal of Mining Science and Technology，2018，28(1)：85–93.
[29] KLEMETTI T M，VAN DYKE M A，TULU I B，et al. A case study of the stability of a non-typical bleeder entry system at a U.S. longwall mine[J]. International Journal of Mining Science and Technology，2020，30(1)：25–31.
[30] MINOSKI T，MCELHINNEY D，COMPTON C，et al. Measurement and analysis of ground movement and load redistribution at a longwall mine in central Utah[C]// Proceedings of the 39th International Conference on Ground Control in Mining. Englewood：Society for Mining，Metallurgy and Exploration，2020：31–41.
[31] 马冰，王学滨，田锋. 基于两种数值模拟方法的围岩脆性破坏特征对比分析[J]. 岩土力学，2021，42(12)：3 440–3 450.(MA Bing，WANG Xuebin，TIAN Feng. Comparative analysis of brittle failure characteristics of surrounding rock based on two numerical simulation methods[J]. Rock and Soil Mechanics，2021，42(12)：3 440–3 450. (in Chinese))
[32] 刘向御，柴肇云，肖畅，等. 煤岩体剪切破裂“缓释”构造及其演进特征[J]. 岩石力学与工程学报，2024，43(1)：170–183.(LIU Xiangyu，CHAI Zhaoyun，XIAO Chang，et al. Shear fracture “slow-release” structure of coal mass and its evolutionary characteristics[J]. Chinese Journal of Rock Mechanics and Engineering，2024，43(1)：170–183.(in Chinese))
[33] 黄庆享，曹健. 浅埋近距煤层开采三场演化规律及煤柱群结构控制效应[J]. 煤炭学报，2021，46(增1)：1–9.(HUANG Qingxiang，CAO Jian. Research on three-field evolution and control effect of pillars structural in shallow buried closely spaced multi-seams mining[J]. Journal of China Coal Society，2021，46(Supp.1)：1–9.(in Chinese))
[34] 郭晓菲，郭林峰，马念杰，等. 巷道围岩蝶形破坏理论的适用性分析[J]. 中国矿业大学学报，2020，49(4)：646–653.(GUO Xiaofei，GUO Linfeng，MA Nianjie，et al. Applicability analysis of the roadway butterfly failure theory[J]. Journal of China University of Mining and Technology，2020，49(4)：646–653.(in Chinese))
[35] ZHANG P，GEARHART D，VAN DYKE M，et al. Ground response to high horizontal stresses during longwall retreat and its implications for longwall headgate support[J]. International Journal of Mining Science and Technology，2019，29(1)：27–33.
[36] 李飞，周家兴，王金安. 基于稀少样本数据的地应力场反演重构方法[J]. 煤炭学报，2019，44(5)：1 421–1 431.(LI Fei，ZHOU Jiaxing，WANG Jin?an. Back-analysis and reconstruction method of in-situ stress field based on limited sample data[J]. Journal of China Coal Society，2019，44(5)：1 421–1 431.(in Chinese))
[37] MARK C，GADDE M. Global trends in coal mine horizontal stress measurements[C]// AZIZ N，NEMCIK J，eds. The 10th Underground Coal Operators? Conference. Wollongong：University of Wollongong and the Australasian Institute of Mining and Metallurgy，2010：21–39.
[38] ESTERHUIZEN G S，BAJPAYEE T S，MURPHY M M，et al. Evaluation of the strength reduction method for US coal mine entry stability analysis[C]// Ground Support 2013：Proceedings of the Seventh International Symposium on Ground Support in Mining and Underground Construction. Perth：Australian Centre for Geomechanics，2013：373–385.
[39] TULU I B，ESTERHUIZEN G S，GEARHART D，et al. Analysis of global and local stress changes in a longwall gateroad[J]. International Journal of Mining Science and Technology，2018，28(1)：127–135.
[40] PENG S S. Longwall mining[M]. 3rd ed. London：CRC Press，2019：40.
[41] ESTERHUIZEN G S，GEARHART D F，KLEMETTI T，et al. Analysis of gateroad stability at two longwall mines based on field monitoring results and numerical model analysis[J]. International Journal of Mining Science and Technology，2019，29(1)：35–43.
[42] JIN Z，LI W，JIN C，et al. Anisotropic elastic，strength，and fracture properties of Marcellus shale[J]. International Journal of Rock Mechanics and Mining Sciences，2018，109：124–137.
[43] CHO J W，KIM H，JEON S，et al. Deformation and strength anisotropy of Asan gneiss，Boryeong shale，and Yeoncheon schist[J]. International Journal of Rock Mechanics and Mining Sciences，2012，50：158–169.
[44] KAISER P K，AMANN F，STEINER W. How highly stressed brittle rock failure impacts tunnel design[C]// ISRM International Symposium-EUROCK 2010. Lausanne：ISRM，2010：27–38.
[45] VAKILI A. An improved unified constitutive model for rock material and guidelines for its application in numerical modelling[J]. Computers and Geotechnics，2016，80：261–282.
[46] LISJAK A，GRASSELLI G，VIETOR T. Continuum-discontinuum analysis of failure mechanisms around unsupported circular excavations in anisotropic clay shales[J]. International Journal of Rock Mechanics and Mining Sciences，2014，65：96–115.
[47] ZHAO X G，CAI M. A mobilized dilation angle model for rocks[J]. International Journal of Rock Mechanics and Mining Sciences，2010，47(3)：368–384.
[48] KANG H，WU Y，GAO F. Deformation characteristics and reinforcement technology for entry subjected to mining-induced stresses[J]. Journal of Rock Mechanics and Geotechnical Engineering，2011，3(3)：207–219.
[49] GUO W，ZHAO G，LOU G，et al. A new method of predicting the height of the fractured water-conducting zone due to high-intensity longwall coal mining in China[J]. Rock Mechanics and Rock Engineering，2019，52(8)：2 789–2 802.