含裂隙岩体点触探破坏机制研究

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (4096 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要岩石点触探试验是间接评估岩体力学特性的重要方法，在其原位应用过程中，岩体的触探特性会受到原位裂隙的重要影响。为了明确岩体裂隙对点触探试验的影响范围，揭示含裂隙岩体点触探的破坏机制，量化不同裂隙对点触探指标的影响，进行一系列含裂隙岩体的室内点触探试验，并通过数值模拟对其破裂机制进行了研究。试验结果表明：点触探加载点下方的影响区域内存在裂隙时会改变点触探破坏模式和强度特性。当裂隙延伸至加载压头附近时，点触探加载下岩体会发生从加载点向该裂隙端部的剪切破坏，裂隙内端的位置决定了点触探的强度及裂纹扩展路径，基于剪切破坏的极限平衡原理可建立点触探强度与剪切路径的对应关系。为了进一步阐明含裂隙点触探破裂规律，通过数值模拟分析了裂隙内端延伸至压头附近不同区域条件时点触探特性，根据破坏模式界定了触探加载点下方的裂隙影响范围，通过定义弱化系数量化了影响区域内不同裂隙对点触探强度的影响程度。同时基于岩体裂隙扩展路径耗能规律，对多裂隙条件下的点触探破裂特性进行了探讨。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	毛芮1
	2
	房凯1
	2
	赵同彬1
	2
	刘念武3

关键词 ：岩石力学, 点触探试验, 破坏机制, 裂隙, 破坏模式

Abstract：Rock cone penetration test is used to evaluate the mechanical properties of in-situ rock indirectly，while the rock failure pattern and mechanical behavior would be severely affected by the pre-existing cracks contained in the in-situ rock mass. To clarify the influence mechanism of the cracks on the cone penetration test and to quantify the effect of the pre-existing cracks on the cone penetration indexes，series of cone penetration tests and numerical simulations were conducted. The test results show that there exists an influence area of cracks below the cone indenter. When the surface crack extends to the vicinity of the loading indenter，shear failure plane generates and propagates from the indenter to the inner tip of the crack. The position of the crack inner tip dominates the cone penetration strength and the crack propagation path，and the correspondence between the cone penetration strength and the shearing path can be established based on the shear limit equilibrium. Additionally，numerical simulations were carried out to analyze the cone penetration behaviors in the case of the crack inner tip extending to different positions near the indenter. Based on the numerical analysis results，it is found that the affected area of the pre-existing crack can be determined according to the failure pattern. Moreover，the weaken coefficient is also defined to quantify the effect of different pre-existing cracks on the penetration strength. Based on the energy dissipation of different fracture paths，the fracture characteristics with multiple cracks under cone penetration test were also discussed.

Key words： rock mechanics cone penetration test failure mechanism crack failure patterns

引用本文:

毛芮1，2，房凯1，2，赵同彬1，2，刘念武3. 含裂隙岩体点触探破坏机制研究[J]. 岩石力学与工程学报, 2022, 41(6): 1183-1192.
MAO Rui1，2，FANG Kai1，2，ZHAO Tongbin1，2，LIU Nianwu3. Failure mechanism of rock with pre-existing surface crack under cone penetration test. , 2022, 41(6): 1183-1192.

链接本文:

http://rockmech.whrsm.ac.cn/CN/Y2022/V41/I6/1183

[5]	STILWELL N A，TABOR D. Elastic recovery of conical indentations[J]. Proceedings of the Physical Society，1961，78(2)：169-179.
[15]	司林坡，康红普. 钻孔点触探法围岩强度原位测试[J]. 煤矿开采，2006，11(4)：10-12.(SI Linpo，KANG Hongpu. In-situ test of surrounding rock strength with bore penetration method[J]. Journal of Mining and Strata Control Engineering，2006，11(4)：10-12.(in Chinese))
[2]	ULUSAY R. The ISRM suggested methods for rock characterization. testing and monitoring：2007—2014[J]. Springer International Publishing，2014，15(1)：47-48.
[3]	SZWEDZICKI T. Draft ISRM suggested method for determining the indentation hardness index of rock materials[J]. International Journal of Rock Mechanics and Mining Sciences，1998，6(35)：831-835.
[8]	ISRM. Suggested method for determining point load strength[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts，1985，22(2)：51-60.
[10]	SZWEDZICKI T. Draft ISRM suggested method for determining the indentation hardness index of rock materials[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts，1998，35(6)：831-835.
[12]	YAGIZ S. Assessment of brittleness using rock strength and density with punch penetration test[J]. Tunnelling Underground Space Technology，2009，24(1)：66-74.
[13]	ULUSAY R，AYDAN，ERGULER Z A，et al. ISRM suggested method for the needle penetration test[J]. Rock Mechanics and Rock Engineering，2014，47(3)：1 073-1 085.
[18]	ZHAO T B，GUO W Y，TAN Y L，et al. Case histories of rock bursts under complicated geological conditions[J]. Bulletin of Engineering Geology Environment，2018，77(4)：1 529-1 545.
[20]	FANG K，ZHAO T B，ZHANG Y B，et al. Rock cone penetration test under lateral confining pressure[J]. International Journal of Rock Mechanics and Mining Sciences，2019，119：149-155.
[22]	WONG L N Y，EINSTEIN H H. Systematic evaluation of cracking behavior in specimens containing single flaws under uniaxial compression[J]. International Journal of Rock Mechanics and Mining Sciences，2009，46(2)：239-249.
[6]	OLIVER W C，PHARR G M. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments[J]. Journal of Materials Research，1992，7(6)：1 564-1 583
[16]	康红普，司林坡. 深部矿区煤岩体强度测试与分析[J]. 岩石力学与工程学报，2009，28(7)：1 312-1 320.(KANG Hongpu，SI Linpo. Test and analysis of coal and rock mass strength in deep coal mine[J]. Chinese Journal of Rock Mechanics and Engineering，2009，28(7)：1 312-1 320.(in Chinese))
[23]	HAERI H，SHAHRIAR K，MARJI M F，et al. Cracks coalescence mechanism and cracks propagation paths in rock-like specimens containing pre-existing random cracks under compression[J]. Journal of Central South University，2014，21(6)：2 404-2 414.
[25]	HOEK E. Rock mechanics laboratory test in the context of a consulting engineering organization[J]. International Journal of Rock Mechanics and Mining Sciences，1977，14(2)：93-101.
[26]	PENG S S. Stress analysis of cylindrical rock discs subjected to axial double point load[J]. International Journal of Rock Mechanics and Mining Sciences，1976，13(3)：97-101.
[28]	BROOKS Z，ULM F J，EINSTEIN H H. Environmental scanning electron microscopy and nanoindentation investigation of the crack tip process zone in marble[J]. Acta Geotechnica，2013，8(3)：223-245.
[30]	张波，李术才，杨学英，等. 含交叉多裂隙类岩石材料单轴压缩力学性能研究[J]. 岩石力学与工程学报，2015，34(9)：1 777-1 785. (ZHANG Bo，LI Shucai，YANG Xueying，et al. Mechanical property of rock-like material with intersecting multi-flaws under uniaxial compression[J]. Chinese Journal of Rock Mechanics and Engineering，2015，34(9)：1 777-1 785.(in Chinese))
[32]	LIU Q，LIU Q，PAN Y，et al. Experimental study on rock indentation using infrared thermography and acoustic emission techniques[J]. Journal of Geophysics and Engineering，2018，15(5)：1 864-1 877.
[33]	ZHAO T B，GUO W Y，TAN Y L，et al. Failure mechanism of layer-crack rock models with different vertical fissure geometric configurations under uniaxial compression[J]. Advance in Mechanical Engineering，Underground Space Technology，2017，9(11)：1-15.
[4]	PHARR G M，OLIVER W C，BROTZEN F R. On the generality of the relationship among contact stiffness，contact area，and elastic modulus during indentation[J]. Journal of Materials Research，1992，7(3)：613-617.
[14]	司林坡. 小孔径钻孔点触探法围岩强度测试原理研究及应用[硕士学位论文][D]. 北京：煤炭科学研究总院，2006.(SI Linpo. Study on in-situ rock strength measurement with contact detection method in small borehole and application[M. S. Thesis][D]. Beijing：China Coal Research Institute，2006.(in Chinese))
[24]	CHEN L H，LABUZ J F. Indentation of rock by wedge-shaped tools[J]. International Journal of Rock Mechanics and Mining Sciences，2006，43(7)：1 023-1 033.
[1]	邬爱清. 岩石力学试验技术及其工程应用的现状与展望[C]// 2009-2010中国岩石力学与工程学会：岩石力学与岩石工程学科发展报告. 北京：[s. n.]，2010：63-71.(WU Aiqing. Present situation and Prospect of rock mechanics test technology and its engineering application[C]// 2009-2010 Chinese Society of Rock Mechanics and Engineering：Development Report of Rock Mechanics and Rock Engineering. Beijing：[s. n.]，2010：63-71.(in Chinese))
[7]	SNEDDON I N. The relation between load and penetration in the axisymmetric boussinesq problem for a punch of arbitrary profile[J]. International Journal of Engineering Science，1965，3(1)：47-57.
[9]	ZHAO T B，FANG K，WANG L，et al. Estimation of elastic modulus of rock using modified point-load test[J]. Geotechnical Testing Journal，2017，40(2)：329-344.
[11]	BAO R H，ZHANG L C，YAO Q Y，et al. Estimating the peak indentation force of the edge chipping of rocks using single point-attack pick[J]. Rock Mechanics and Rock Engineering，2011，44(3)：339-347.
[17]	YIN L J，GONG Q M，ZHAO J. Study on rock mass boreability by TBM penetration test under different in situ stress conditions[J]. Tunnelling and Underground Space Technology，2014，72(43)：261-276.
[19]	周军华. 钻孔条件下岩石点触探特性及其力学行为研究[硕士学位论文][D]. 青岛：山东科技大学，2019.(ZHOU Junhua. Study on rock penetration characteristics and mechanical behaviour under borehole conditions[M. S. Thesis][D]. Qingdao：Shandong University of Science and Technology，2019.(in Chinese))
[21]	LI X F，LI H B，LIU Y Q，et al. Numerical simulation of rock fragmentation mechanisms subject to wedge penetration for TBMs[J]. Tunnelling and Underground Space Technology，2016，53：96-108.
[27]	REICHMUTH D R. Point load test of brittle materials to determine tensile strength and relative brittleness[J]. Status of Practical Rock Mechanics，1968，(9)：134-159.
[29]	WANG J L，MA D J，SUN L. The influence of crack forms on indentation hardness test results for ceramic materials[J]. Journal of Materials Science，2015，50(18)：6 096-6 102.
[31]	李术才，许新骥，刘征宇，等. 单轴压缩条件下砂岩破坏全过程电阻率与声发射响应特征及损伤演化[J]. 岩石力学与工程学报，2014，33(1)：14-23.(LI Shucai，XU Xinji，LIU Zhengyu，et al. Elecrtrical resistivity and acousitic emission response characteristics and damage evolution of sandstone during whole process of uniaxial compression[J]. Chinese Journal of Rock Mechanics and Engineering，2014，33(1)：14-23.(in Chinese))