Study of coal face failure mechanism of a large-cutting-height mining face
KONG Dezhong1，2，LIU Yang1，LIU Qinzhi1
(1. College of Mining，Guizhou University，Guiyang，Guizhou 550025；2. Research Center of Top-coal Caving Mining in Coal Mining Industry，Beijing 100083，China)
In response to the condition that coal face spalling and roof-fall occurring frequently in the large-cutting-height mining face，taking panel 8101 of Wangzhuang coal mine as background，the“roof-coal face-support”system mechanical model has been established to conduct the influence factors sensitivity analysis of coal face stability. Experimental test for coal face stability study has been designed to conduct similarity simulation test in order to study the relations between coal face stability and influence factors such as mining height，support working resistance，coal face pressure and coal strength. UDEC numerical simulation was used to simulate the coal face deformation in changing mining height，cohesion，support capacity and advancing length. The study shows that coal face pressure and coal strength are the main reason that causing coal face failure. The larger is the mining height，the smaller is the limited coal face failure pressure. The larger is the support capacity，the smaller is the coal face pressure. However，improving of support capacity only has limit impact on coal wall failure controlling. Guard board of support can prevent the fractured coal face from sliding down effectively but has little impact on coal face failure controlling. There is a large deformation in coal body before the coal face failure. The coal face failure position locates as the upper part of coal face，usually 60%–70% of mining height. These results provide a foundation for coal face spalling prevention.
孔德中1，2，刘 洋1，刘勤志1. 大采高工作面煤壁破坏机制研究[J]. 岩石力学与工程学报, 2018, 37(S1): 3458-3469.
KONG Dezhong1，2，LIU Yang1，LIU Qinzhi1. Study of coal face failure mechanism of a large-cutting-height mining face. , 2018, 37(S1): 3458-3469.
王家臣.厚煤层开采理论与技术[M].北京：冶金工业出版社，2009：117-118.(WANG Jiachen. The mining theory and technique of thick coal seam[M].Beijing：Metallurgical Industry Press，2009：117-118.(in Chinese))
[2]
王家臣，王 蕾，郭尧. 基于顶板与煤壁控制的支架阻力的确定[J]. 煤炭学报，2014，39(8)：1619-1624.(WANG Jiachen，WANG Lei，GUO Yao. Determining the support capacity based on roof and coal wall control[J]. Journal of China Coal Society，2014，39(8)：1619- 1624.(in Chinese))
[3]
王家臣，王兆会，孔德中.硬煤工作面煤壁破坏与防治机理[J].煤炭学报，2015，40(10)：2243-2250.(WANG Jiachen，WANG Zhaohui，KONG Dezhong. Failure and prevention mechanism of coal wall in hard coal[J]. Journal of China Coal Society，2015，40(10)：2243-2250.(in Chinese))
[4]
赵宏珠.大采高支架采面煤壁片帮规律及防护[J].矿山压力，1989，(2)：27-29.(ZHAO Hongzhu. The control and mechanism of rib spalling in large mining face[J]. The Mine Pressure，1989，(2)：27-29.(in Chinese))
[5]
杨培举，刘长友，吴锋锋. 厚煤层大采高采场煤壁的破坏规律与失稳机理[J]. 中国矿业大学学报，2012，41(3)：372-377.(YANG Peiju，LIU Changyou，WU Fengfeng. Breakage and falling of a high coal face in a thick mined seam[J].Journal of China University of Mining and Technology，2012，41(3)：372-377.(in Chinese))
[6]
刘长友，黄炳香，常兴民，等. 极软厚煤层大采高台阶式综采端面煤岩稳定性控制研究[J].中国矿业大学学报，2008，37(6)：734-739.(LIU Changyou，HUANG Bingxiang，CHANG Xingming，et al. Study on tip to face coal and rock stability control of fully mechanized stepped large cutting height mining in extremely soft thick seam[J].Journal of China University of Mining andTechnology，2008，37(6)：734-739.(in Chinese))
[7]
王家臣.极软厚煤层煤壁片帮与防治机理[J].煤炭学报，2007，32(8)：785-788.(WANG Jiachen. Mechanism of the rib spalling and the controlling in the very soft coal seam[J].Journal of China Coal Society，2007，32(8)：785-788.(in Chinese))
[8]
WANG JC，YANG S L，KONG DZ. Failuremechanism and control technology of Longwall coal face in large-cutting-height mining method[J].International Journal of Mining Science and Technology，2016，26(1)：111-118.(in Chinese))
[9]
王家臣，杨印朝，孔德中，等.含夹矸厚煤层大采高仰采煤壁片帮机理与注浆加固技术[J]. 采矿与安全工程学报，2014，31(6)：831-837.(WANG Jiachen，YANG Yinchao，KONG Dezhong，et al. Failure mechanism and grouting reinforcement technique of large mining height coal wall in thick coal seam with dirt band during topple mining[J]. Journal of Mining andSafety Engineering，2014，31(6)：831-837.(in Chinese))
[10]
杨胜利，孔德中.大采高煤壁片帮防治柔性加固机理与应用[J].煤炭学报，2015，40(6)：1361-1367.(YANG Shengli，KONG Dezhong. Flexible reinforcement mechanism and its application in the control of spalling at large mining height coal face[J]. Journal of China Coal Society，2015，40(6)：1361-1367.(in Chinese))
[11]
杨胜利，孔德中，杨敬虎，等. 综放仰斜开采煤壁稳定性及注浆加固技术[J].采矿与安全工程学报，2015，32(5)：827-833.(YANG Shengli，KONG Dezhong，YANG Jinghu，et al. Coal wall stability and grouting reinforcement technique in fully mechanized caving face during topple mining[J].Journal of Mining andSafety Engineering，2015，32(5)：827-833.(in Chinese))
[12]
孔德中，杨胜利，张锦旺，等. 煤样强度特征的浆液量效应试验研究[J].采矿与安全工程学报，2015，32(3)：420-425.(KONG Dezhong，YANG Shengli，ZHANG Jinwang，et al. The experimental study of the grout quantity effect of strength properties of coal sample[J].Journal of Mining andSafety Engineering，2015，32(3)：420-425.(in Chinese)
[13]
郝海金，张勇.大采高开采工作面煤壁稳定性随机分析[J].辽宁工程技术大学学报，2005，24(4)：489-491.(HAO Haijin，ZHANG Yong. Stability analysis of coal wall in full-seam cutting workface with fully-mechanized in thick seam[J]. Journal of Liaoning Technical University，2005，24(4)：489-491.(in Chinese))
[14]
王兆会，杨敬虎，孟 浩. 大采高工作面过断层构造煤壁片帮机理及控制[J]. 煤炭学报，2015，40(10)：42-49.(WANG Zhaohui，YANG Jinghu，MENG Hao. Mechanism and controlling technology of rib spalling in mining face with large cutting height passing through fault[J]. Journal of China Coal Society，2015，40(10)：42-49.(in Chinese))
[15]
闰少宏.大采高综放开采煤壁片帮冒顶机理与控制途径研究[J].煤矿开采，2008，13(4)：10-13.(YAN Shaohong. Research on side and roof falling mechanism and control approaches in full-mechanized caving mining with large mining height[J].Coal Mining Technology，2008，13(4)：10-13.(in Chinese))
[16]
袁永，屠世浩，马小涛，等.“三软”大采高综采面煤壁稳定性及其控制研究[J].采矿与安全工程学报，2012，29(1)：22-25.(YUAN Yong，TU Shihao，MA Xiaotao，et al. Coal wall stability of fully mechanized working face with great mining height in‘three soft¢coal seam and its control technology[J].Journal of Mining andSafety Engineering，2012，29(1)：22-25.(in Chinese)
2018, Vol. 37 
