局部安全系数引入下岩质边坡稳定性分析极限平衡滑面应力法

doi:10.13722/j.cnki.jrme.2023.0545

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (4231 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要由于广义非线性Hoek-Brown(H-B)强度准则可展现出岩体的复杂剪切破坏行为，因此，其被广泛地应用于岩质边坡稳定性分析。然而，以条块划分与条间力假设模式而建立的传统极限平衡方法不易于直接引入非线性强度准则，使得极限平衡方法在分析岩质边坡稳定性方面存在些许不足。此外，边坡稳定性分析时，以往常将滑面局部安全系数假定为与位置无关的单一变量。事实上，边坡在未达到临界失效状态前，滑面局部安全系数分布存在差异性。为此，应用Taylor级数展开式构建滑面正应力函数，并考虑滑面局部安全系数差异性，建立滑面局部安全系数倒数线性分布特征下滑面剪应力函数。进而，实现滑面应力计算模式与滑面局部安全系数差异分布特征下广义非线性H-B强度准则的融入。随后，引入滑面端部应力约束条件，并依据边坡滑体所满足的整体力学平衡方程，推导出岩质边坡稳定性极限平衡解答。通过算例对比分析，可知本文方法不仅可准确地评估出非线性强度准则下岩质边坡稳定性，而且能够合理地模拟出近坡顶处滑面拉剪应力区、客观地描述出应力集中效应下近坡脚处滑面压剪现象以及有效地判别出滑面局部安全系数差异分布特征。进一步，为了便于指导工程岩质边坡设计与加固，绘制了均质岩石边坡最小安全系数等值曲线图与临界滑面局部安全系数差异分布特征分区图。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	邓东平
	彭一航
	陈浩宇
	王翊民

关键词 ：边坡工程, 广义非线性H-B强度准则, 岩质边坡稳定性, 极限平衡, 滑面应力, 滑面局部安全系数, 滑面端部应力约束条件

Abstract：Because the generalized nonlinear Hoek-Brown(H-B) strength criterion can exhibit the complex shear failure behavior of rock mass，it is widely used in the stability analysis of rock slope. However，the traditional limit equilibrium(LE) methods based on the slice division and assumption of inter-slice forces is not easy to directly introduce the nonlinear strength criterion，which makes the LE methods have some shortcomings in analyzing the stability of rock slopes. In addition，the local factor of safety(FOS) of slip surface is usually assumed as a single variable independent of its position in the analysis of slope stability. In fact，before the slope reaches the critical failure state，the distribution of the local FOS of the slip surface is different. Here，the Taylor series expansion is applied to construct the function of the normal stress on the slip surface，and the function of the shear stress on the slip surface under the linear distribution characteristics of the reciprocal of the local FOS of the slip surface is established to consider the difference of the local FOS of the slip surface. Thereby，the generalized nonlinear H-B strength criterion is integrated with the calculation mode of the stresses on the slip surface and the difference distribution characteristics of the local FOS of slip surface. Thereafter，the stress constraint conditions at both ends of the slip surface is introduced，and then the LE solution of rock slope stability is derived according to the mechanical equilibrium conditions of the sliding body. Through the comparison and analysis of examples，it can be verified that the proposed method can not only accurately evaluate the stability of rock slope under the generalized nonlinear H-B strength criterion，but also reasonably simulate the tension-shear stress zone of the slip surface near the slope top，objectively describe the compression-shear phenomenon of slip surface near slope toe under the stress concentration effect，and effectively distinguish the difference distribution characteristics of the local FOS of the slip surface. Furthermore，in order to facilitate the guidance of design and reinforcement of engineering rock slope，the equivalent curves of the minimum FOS of homogeneous rock slope and the partition diagrams of the difference distribution characteristics of the local FOS of the critical slip surface are drawn.

Key words： slope engineering generalized nonlinear H-B strength criterion stability of rock slope limit equilibrium stresses of slip surface local factor of safety of slip surface stress constraint conditions at both ends of slip surface

引用本文:

邓东平，彭一航，陈浩宇，王翊民 . 局部安全系数引入下岩质边坡稳定性分析极限平衡滑面应力法[J]. 岩石力学与工程学报, 2024, 43(4): 964-985.
DENG Dongping，PENG Yihang，CHEN Haoyu，WANG Yimin. Limit equilibrium method based on stresses of slip surface for stability analysis of rock slope with introduction of local factor of safety. , 2024, 43(4): 964-985.

链接本文:

https://rockmech.whrsm.ac.cn/CN/10.13722/j.cnki.jrme.2023.0545 或 https://rockmech.whrsm.ac.cn/CN/Y2024/V43/I4/964

[1] KHAN M I，WANG S. Slope stability analysis to correlate shear strength with slope angle and shear stress by considering saturated and unsaturated seismic conditions[J]. Applied Sciences，2021，11(10)：4 568.
[2] RENANI H R，MARTIN C D. Slope stability analysis using equivalent Mohr-Coulomb and Hoek-Brown criteria[J]. Rock Mechanics and Rock Engineering，2020，53(1)：13–21.
[3] ZHAO L，YU C，LI L，et al. Rock slope reliability analysis using Barton-Bandis failure criterion with modified pseudo-dynamic approach[J]. Soil Dynamics and Earthquake Engineering，2020，139(6)：106310.
[4] 朱合华，张琦，章连洋. Hoek-Brown强度准则研究进展与应用综述[J]. 岩石力学与工程学报，2013，32(10)：1 945–1 963.(ZHU Hehua，ZHANG Qi，ZHANG Lianyang. Review of research progresses and applications of Hoek-Brown strength criterion[J]. Chinese Journal of Rock Mechanics and Engineering，2013，32(10)：1 945–1 963.(in Chinese))
[5] HOEK E，BROWN E T. The Hoek-Brown failure criterion and GSI - 2018 edition[J]. Journal of Rock Mechanics and Geotechnical Engineering，2019，11(3)：445–463.
[6] LEE Y K，PIETRUSZCZAK S. Limit equilibrium analysis incorporating the generalized Hoek-Brown criterion[J]. Rock Mechanics and Rock Engineering，2021，54(9)：4 407–4 418.
[7] DENG D，ZHAO L，LI L. Limit equilibrium analysis for rock slope stability using basic Hoek-Brown strength criterion[J]. Journal of Central South University，2017，24(9)：2 154–2 163.
[8] SARKAR S，CHAKRABORTY M. Pseudostatic stability analysis of rock slopes using variational method[J]. Indian Geotechnical Journal，2021，51(5)：935–951.
[9] LI D，JIA W，ZHAO L，et al. Upper-Bound limit analysis of rock slope stability with tensile strength cutoff based on the optimization strategy of dividing the tension zone and shear zone[J]. International Journal of Geomechanics，2022，22(5)：06022006.
[10] 王伟，陈国庆，朱静，等. 考虑张拉–剪切渐进破坏的边坡强度折减法研究[J]. 岩石力学与工程学报，2018，37(9)：2 064–2 074. (WANG Wei，CHEN Guoqing，ZHU Jing，et al. Slope stability calculated with strength reduction method considering tensile and shear progressive failure[J]. Chinese Journal of Rock Mechanics and Engineering，2018，37(9)：2 064–2 074.(in Chinese))
[11] LI Y，FENG X，YAO A，et al. Progressive evolution and failure behavior of a Holocene river-damming landslide in the SE Tibetan Plateau，China[J]. Landslides，2022，19(5)：1 069–1 086.
[12] 陈国庆，唐辉明，胡凯云，等. 基于非均质流变特性的滑坡时效演化及预警研究[J]. 岩石力学与工程学报，2022，41(9)：1 795–1 809. (CHEN Guoqing，TANG Huiming，HU Kaiyun，et al. Evolution characteristics and early warning of landslides based on heterogeneous rheological properties[J]. Chinese Journal of Rock Mechanics and Engineering，2022，41(9)：1 795–1 809.(in Chinese))
[13] DRESCHER A，CHRISTOPOULOS C. Limit analysis slope stability with nonlinear yield condition[J]. International Journal for Numerical and Analytical Methods in Geomechanics，1988，12(3)：341–345.
[14] 胡卫东，曹文贵，袁青松. 基于非线性破坏准则的临坡地基承载力上限分析[J]. 岩土力学，2017，38(6)：1 639–1 646.(HU Weidong，CAO Wengui，YUAN Qinsong. Upper bound solution for ultimate bearing capacity of ground adjacent to slope based on nonlinear failure criterion[J]. Rock and Soil Mechanics，2017，38(6)：1 639–1 646.(in Chinese))
[15] AHMED Z，WANG S，JASIM O H，et al. Variability effect of strength and geometric parameters on the stability factor of failure surfaces of rock slope by numerical analysis[J]. Arabian Journal of Geosciences，2020，13(21)：1 112.
[16] BAKER R，GARBER M. Theoretical analysis of the stability of slopes[J]. Géotechnique，1978，28(4)：395–411.
[17] LESHCHINSKY D，SAN K C. Pseudostatic seismic stability of slopes：design charts[J]. Journal of Geotechnical Engineering，1994， 120(9)：1 514–1 532.
[18] LOW B K，TANG W. Probabilistic slope analysis using Janbu?s generalized procedure of slices[J]. Computers and Geotechnics，1997，21(2)：121–142.
[19] YANG X，YANG Z，LI Y，et al. Upper bound solution for supporting pressure acting on shallow tunnel based on modified tangential technique[J]. Journal of Central South University of Technology，2013，20(12)：3 676–3 682.
[20] FU W，LIAO Y. Non-linear shear strength reduction technique in slope stability calculation[J]. Computers and Geotechnics，2010，37(3)：288–298.
[21] LESHCHINSKY D，BAKER R，SILVER M L. Three dimensional analysis of slope stability[J]. International Journal for Numerical and Analytical Methods in Geomechanics，1985，9(3)：199–223.
[22] CHING R K H，FREDLUND D G. Some difficulties associated with the limit equilibrium method of slices[J]. Canadian Geotechnical Journal，1983，20(4)：661–672.
[23] HOU C，ZHANG R，LI Y，et al. Comparisons of factor of safety for slope in nonlinear soils[J]. KSCE Journal of Civil Engineering，2021，25(10)：3 737–3 749.
[24] UTILI S. Investigation by limit analysis on the stability of slopes with cracks[J]. Géotechnique，2013，63(2)：140–154.
[25] MICHALOWSKI R L. Stability assessment of slopes with cracks using limit analysis[J]. Canadian Geotechnical Journal，2013，50(10)：1 011–1 021.
[26] PARK D，MICHALOWSKI R L. Three-dimensional stability analysis of slopes in hard soil/soft rock with tensile strength cut-off[J]. Engineering Geology，2017，229(11)：73–84.
[27] SUN L，LIU Q，ABDELAZIZ A，et al. Simulating the entire progressive failure process of rock slopes using the combined finite-discrete element method[J]. Computers and Geotechnics，2022，141(1)：104557.
[28] CHENG Y，LI D，LI L，et al. Limit equilibrium method based on an approximate lower bound method with a variable factor of safety that can consider residual strength[J]. Computers and Geotechnics，2011，38(5)：623–637.
[29] GAO W，DAI S，XIAO T，et al. Failure process of rock slopes with cracks based on the fracture mechanics method[J]. Engineering Geology，2017，231(12)：190–199.
[30] BELANDRIA N，ÚCAR R，CORREDOR A，et al. Safety factor on rock slopes with tensile cracks using numerical and limit equilibrium models[J]. Geotechnical and Geological Engineering，2021，39(11)：2 287–2 300.
[31] ZHANG Y，LIU Y，YUAN R，et al. Comparison of seismic stability for slopes with tensile strength cut-off and cracks[J]. Journal of Mountain Science，2021，18(12)：3 336–3 347.
[32] LIANG L，ZHAI Z，WU Z. Influence of the reservoir position on sponge slope stability[C]// Proceedings of the 2nd Global Conference on Ecological Environment and Civil Engineering. [S. l.]：[s. n.]，2020：01202.
[33] DO T，WU J. Simulating a mining-triggered rock avalanche using DDA：A case study in Nattai North，Australia[J]. Engineering Geology，2020，264(1)：105386.
[34] YANG T，YEUNG M C R，YANG B，et al. Three-dimensional stability of landslides based on local factor of safety[J]. Journal of Mountain Science，2016，13(9)：1 515–1 526.
[35] QI C，QI J，LI L，et al. Stability analysis method for rock slope with an irregular shear plane based on interface model[J]. Advances in Civil Engineering，2018，11(4)：8190908.
[36] CHUGH A K. Variable factor of safety in slope stability analysis[J]. Géotechnique，1986，36(1)：57–64.
[37] ZHANG M，NIE L，XU Y，et al. A thrust load-caused landslide triggered by excavation of the slope toe：a case study of the Chaancun Landslide in Dalian City，China[J]. Arabian Journal of Geosciences，2015，8(9)：6 555–6 565.
[38] WANG H，SUN P，WANG G，et al. Experimental and numerical study of shallow loess slope failure induced by irrigation[J]. Catena，2021，206(11)：105548.
[39] 雍睿，胡新丽，唐辉明，等. 推移式滑坡演化过程模型试验与数值模拟研究[J]. 岩土力学，2013，34(10)：3 018–3 027.(YONG Rui，HU Xinli，TANG Huiming，et al. Model testing and numerical simulation study of evolutionary process of thrust load caused landslide[J]. Rock and Soil Mechanics，2013，34(10)：3 018–3 027. (in Chinese))
[40] DENG D. Limit equilibrium solution for the rock slope stability under the coupling effect of the shear dilatancy and strain softening[J]. International Journal of Rock Mechanics and Mining Sciences，2020，134(10)：104421.
[41] DENG D. Novel model for limit-equilibrium analysis of slope stability with a nonlinear strength criterion[J]. International Journal of Geomechanics，2021，21(9)：06021021.
[42] BELL J. General slope stability analysis[J]. Journal of the Soil Mechanics and Foundations Division，1968，94(SM6)：1 253–1 270.
[43] ZHU D，LEE C F. Explicit limit equilibrium solution for slope stability[J]. International Journal for Numerical and Analytical Methods in Geomechanics，2002，26(15)：1 573–1 590.
[44] DENG D，ZHAO L，LI L. Limit equilibrium slope stability analysis using the nonlinear strength failure criterion[J]. Canadian Geotechnical Journal，2015，52(5)：563–576.
[45] ZHENG H，THAM L G. Improved Bell's method for the stability analysis of slopes[J]. International Journal for Numerical and Analytical Methods in Geomechanics，2009，33(14)：1 673–1 689.
[46] KUMAR P. Shear failure envelope of Hoek-Brown criterion for rockmass[J]. Tunnelling and Underground Space Technology，1998，13(4)：453–458.
[47] HOEK E，CARRANZA-TORRES C，CORKUM B. Hoek-Brown failure criterion-2002 edition[C]// Proceedings of NARMS-TAC Conference. Toronto：[s. n.]，2002：267–273.
[48] Itasca Consulting Group. FlAC3D 6.0 theory and background[M]. Minnesota：Itasca Consulting Group Inc.，2017：87–151.
[49] LI A J，MERIFIELD R S，LYAMIN A V. Stability charts for rock slopes based on the Hoek-Brown failure criterion[J]. International Journal of Rock Mechanics and Mining Sciences，2008，45(5)：689–700.
[50] ARAI K，TAGYO K. Determination of noncircular slip surface giving the minimum factor of safety in slope stability analysis[J]. Soils and Foundations，1985，25(1)：43–51.
[51] Rocscience Inc.. Slide 2 Documentation—analysis methods[M]. Toronto：Rocscience Inc.，2012：1–5.
[52] Itasca Consulting Group. Fast Lagrangian analysis of continua—factor of safety[M]. Minnesota：Itasca Consulting Group Inc.，2011：1–88.
[53] BANDINI P，SALGADO R，LOUKIDIS D. Stability of seismically loaded slopes using limit analysis[J]. Géotechnique，2003，53(5)： 463–480.