滑动面力学参数对滑坡稳定性影响研究 ——以重庆武隆鸡尾山滑坡为例

doi:10.13722/j.cnki.jrme.2014.s2.061

摘要
图/表
参考文献(35)
相关文章 (15)

全文: PDF (2513 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要为研究武隆鸡尾山滑坡的滑动面节理参数(法向刚度JKN，切向刚度JKS，内摩擦角，黏聚力c)对变形特征影响的显著性，基于正交试验设计原理，运用大型3D离散元软件3DEC进行数值模拟试验，将监测点位移量作为试验指标，方差分析结果显示：(1) 滑动面切向刚度JKS和内摩擦角对水平和竖向位移具有高度显著性影响，而滑动面法向刚度JKN和黏聚力c对滑体的位移影响有限；(2) 滑动面节理力学参数对稳定性影响作用主次顺序为JKS＞＞JKN＞c(水平位移)；JKS＞＞c＞JKN(竖向位移)。最后又以正交试验16个案例中最危险案例5为典型，调查了滑坡破坏过程中的位移变化特征：破坏初期，对于水平(EW方向)位移，滑体关键块体在前缘山体的阻挡下，主要向东侧悬崖方向滑动，关键块体的位移量远远大于后面的驱动块体；对于SN方向上的水平位移以及竖向位移，驱动块体的位移量远远大于关键块体。同时数值模拟结果也显示，前缘关键块体先于后部驱动块体发生整体破坏，率先滑向悬崖。模拟结果与实际情况一致。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	葛云峰1
	2
	3
	唐辉明1
	熊承仁4
	王亮清1
	吴益平1

关键词 ：边坡工程, 鸡尾山滑坡, 正交试验设计, 稳定性评价

Abstract：In order to investigate the influence of mechanical parameters of sliding plane，normal stiffness JKN，shearing stiffness JKS，internal friction angle ，and cohesion c，on the rockslide stability，the numerical simulations were conducted based on the orthogonal design method and 3D discrete element software 3DEC，the displacements concerning a monitoring point located in the front of sliding block were chosen as indicator in the orthogonal experiment. The analysis of variance shows that：(1) JKS and of sliding plane have a significant effect on the displacement of monitoring point along all of X，Y，and Z direction，as for the c and JKN，it seems that they have a limited influence on the displacement. (2) According to the influence degree on the rockslide stability，the order for 4 mechanical parameters may be arranged by JKS＞＞JKN＞c(for horizonal displacement)；JKS＞＞c＞JKN(for vertical displacement). The next research was focused on the most dangerous case among the 16 cases，in the initial stage of failure，for the horizontal displacement(EW)，the key block mainly moves to the east cliff due to the support from the rock mass，the amount of displacement for key block is much larger than that for driving block. For the horizontal displacement(SN) and vertical displacement，the displacement for driving block is bigger than that for key block. It can been seen that the key block slides down to the cliff following by driving block，numerical simulation results make a good agreement with the real situation.

Key words： slope engineering Jiweishan landslide orthogonal design stability evaluation

引用本文:

葛云峰1，2，3，唐辉明1，熊承仁4，王亮清1，吴益平1. 滑动面力学参数对滑坡稳定性影响研究 ——以重庆武隆鸡尾山滑坡为例[J]. 岩石力学与工程学报, 2014, 33(S2): 3873-3884.
GE Yunfeng1，2，3，TANG Huiming1，XIONG Chengren4，WANG Liangqing1，WU Yiping1. EFFECT OF SLIDING PLANE MECHANICAL PARAMETERS ON LANDSLIDE STABILITY——A CASE STUDY OF JIWEISHAN ROCKSLIDE IN WULONG，CHONGQING. , 2014, 33(S2): 3873-3884.

链接本文:

https://rockmech.whrsm.ac.cn/CN/10.13722/j.cnki.jrme.2014.s2.061 或 https://rockmech.whrsm.ac.cn/CN/Y2014/V33/IS2/3873

[1]	许强，黄润秋，殷跃平，等. 2009年6·5重庆武隆鸡尾山崩滑灾害基本特征与成因机制初步研究[J]. 工程地质学报，2009，17(4)：433-444.(XU Qiang，HUANG Runqiu，YIN Yueping，et al. The Jiweishan landslide of June 5，2009 in Wulong，Chongqing：characteristics and failure mechanism[J]. Journal of Engineering Geology，2009，17(4)：433-444.(in Chinese))
[2]	殷跃平. 斜倾厚层山体滑坡视向滑动机制研究——以重庆武隆鸡尾山滑坡为例[J]. 岩石力学与工程学报，2010，29(2)：217-226.(YIN Yueping. Mechanism of apparent dip slide of inclined bedding rockslide——a case study of Jiweishan rockslide in Wulong，Chongqing[J]. Chinese Journal of Rock Mechanics and Engineering，2010，29(2)：217-226.(in Chinese))
[3]	刘传正. 重庆武隆鸡尾山危岩体形成与崩塌成因分析[J]. 工程地质学报，2010，18(3)：297-304.(LIU Chuanzheng. Mechanism analysis of the Jiweishan rockfall disaster happened in Wulong，Chongqing[J]. Journal of Engineering Geology，2010，18(3)：297-304.(in Chinese))
[4]	XUQ，FANXM，HUANGRQ，et al. A catastrophic rockslide—debris flow in Wulong，Chongqing，China in 2009：background，characterization，and causes[J]. Landslides，2010，7(1)：75-87.
[5]	冯振，殷跃平，李滨，等. 重庆武隆鸡尾山滑坡视向滑动机制分析[J]. 岩土力学，2012，33(9)：2 704-2 712.(FENG Zhen，YIN Yueping，LI Bin，et al. Mechanism analysis of apparent dip landslide of Jiweishan in Wulong，Chongqing[J]. Rock and Soil Mechanics，2012，33(9)：2 704-2 712.(in Chinese))
[6]	彭国喜. 西南山区“关键块体”控制型滑坡的形成条件与失稳机制研究——以重庆武隆鸡尾山滑坡为例[硕士学位论文][D]. 成都：成都理工大学，2011.(PENG Guoxi. Research onthe formative condition and instability mechanismof the landslide controlled by the key blocks in southwest mountainous—the Cocktail mountain landslidein Chongqing Wulong，for example[M. S. Thesis][D]. Chengdu：Chengdu University of Technology，2011.(in Chinese))
[7]	邹宗兴，唐辉明，熊承仁，等. 大型顺层岩质滑坡渐进破坏地质力学模型与稳定性分析[J]. 岩石力学与工程学报，2012，31(11)：2 222- 2 231.(ZOU Zongxing，TANG Huiming，XIONG Chengren，et al. Geomechanical model of progressive failure for large consequent bedding rockslide and its stability analysis[J]. Chinese Journal of Rock Mechanics and Engineering，2012，31(11)：2 222-2 231.(in Chinese))
[8]	韩金良. 复杂山体特大滑坡形成机制与大型物理模拟试验研究[R]. 北京：中国地质科学院地质力学研究所，2011.(HAN Jinliang. Study on formation mechanism of complex and large landslide and large physical simulation tests[R]. Beijing：Institute of Geomechanics，Chinese Academy of Geological Sciences，2011.(in Chinese))
[9]	王灵敏，刘志刚，耿协威，等. 鸡尾山大型高速滑坡近程飞行数值分析[J]. 人民长江，2012，43(2)：62-65.(WANG Lingmin，LIU Zhigang，GENG Xiewei，et al. Numerical analysis of short-range flying of large-scale and high-speed Jiweishan landslide[J]. Yangtze River，2012，43(2)：62-65.(in Chinese))
[10]	YINYP，SUNP，ZHANGM，et al. Mechanism on apparent dip sliding of oblique inclined bedding rockslide at Jiweishan，Chongqing，China[J]. Landslides，2011，8(1)：49-65.
[11]	张龙，唐辉明，熊承仁，等. 鸡尾山高速远程滑坡运动过程PFC3D模拟[J]. 岩石力学与工程学报，2012，31(增1)：2 601-2 611. (ZHANG Long，TANG Huiming，XIONG Chengren，et al. Movement process simulation of high-speed long-distance Jiweishan landslide with PFC3D[J]. Chinese Journal of Rock Mechanics and Engineering，2012，31(Supp.1)：2 601-2 611.(in Chinese))
[12]	李腾飞，李晓，李守定，等. 地下开采诱发斜坡失稳破坏机制研究——以武隆鸡尾山崩滑为例[J]. 岩石力学与工程学报，2012，31(增2)：3 803-3 810.(LI Tengfei，LI Xiao，LI Shouding，et al. Mechanism of slope failure induced by undermining—a case study of Jiweishan rockslide in Wulong[J]. Chinese Journal of Rock Mechanics and Engineering，2012，31(Supp. 2)：3 803-3 810.(in Chinese))
[13]	许强. 西南复杂斜坡滑坡形成条件与失稳机制研究[R]. 成都：成都理工大学，2010.(XU Qiang. Study of formation condition and instability mechanism of southwest complex slope[R]. Chengdu：Chengdu University of Technology，2010.(in Chinese))
[14]	唐辉明，熊承仁，苏爱军，等. 高速远程滑坡形成机制研究新开工作项目设计书[R]. 武汉：中国地质大学，2010.(TANGHuiming，XIONGChengren，SUAijun，et al. The study on the forming mechanism of high speed and long distance landslide[R]. Wuhan：China University of Geosciences，2010.(in Chinese))
[15]	唐辉明，葛云峰，熊承仁，等. 滑动面岩体综合实验报告初稿[R]. 武汉：中国地质大学，2012.(TANGHuiming，GE Yunfeng，XIONGChengren，et al. The draft report of comprehensive experiment for samples from sliding plane[R]. Wuhan：China University of Geosciences，2012.(in Chinese))
[16]	WU Q，KULATILAKE P H S W. Application of equivalent continuum and discontinuum stress analyses in three-dimensions to investigate stability of a rock tunnel in a dam site in China[J]. Computers and Geotechnics，2012，46(1)：48-68.
[17]	WANG X，KULATILAKE P H S W，SONG W D. Stability investigations around a mine tunnel through three-dimensional discontinuum and continuum stress analyses[J]. Tunnelling and Underground Space Technology，2012，32(1)：98-112.
[18]	周火明，盛谦，邬爱清. 三峡工程永久船闸边坡岩体宏观力学参数的尺寸效应研究[J]. 岩石力学与工程学报，2001，20(5)：661-664.(ZHOU Huoming，SHENG Qian，WU Aiqing. Size effect analysis on macro-mechanics parameters for the rock masses of the TGP shiplock slope[J]. Chinese Journal of Rock Mechanics and Engineering，2001，20(5)：661-664.(in Chinese))
[19]	倪恒，刘佑荣，龙治国. 正交设计在滑坡敏感性分析中的应用[J]. 岩石力学与工程学报，2002，21(7)：989-992.(NI Heng，LIU Yourong，LONG Zhiguo. Application of orthogonal design to sensitivity analysis of landslide[J]. Chinese Journal of Rock Mechanicsand Engineering，2002，21(7)：989-992.(in Chinese))
[20]	赵洪波，冯夏庭. 位移反分析的进化支持向量机研究[J]. 岩石力学与工程学报，2003，22(10)：1 618-1 622.(ZHAO Hongbo，FENG Xiating. Study on genetic-support vector machine in displacement back analysis[J]. Chinese Journal of Rock Mechanics and Engineering，2003，22(10)：1 618-1 622.(in Chinese))
[21]	吴顺川，高永涛，杨占峰. 基于正交试验的露天矿高陡边坡落石随机预测[J]. 岩石力学与工程学报，2006，25(增1)：2 826-2 832.(WU Shunchuan，GAO Yongtao，YANG Zhanfeng. Random prediction of rockfall of open-pit mine high-steep slope based on orthogonal experiment[J]. Chinese Journal of Rock Mechanics and Engineering，2006，25(Supp. 1)：2 826-2 832.(in Chinese))
[22]	冯夏庭，周辉，李邵军，等. 岩石力学与工程综合集成智能反馈分析方法及应用[J]. 岩石力学与工程学报，2007，26(9)：1 737- 1 744.(FENG Xiating，ZHOU Hui，LI Shaojun，et al. Integrated intelligent feedback analysis of rock mechanics and engineering problems and its application[J]. Chinese Journal of Rock Mechanics and Engineering，2007，26(9)：1 737-1 744.(in Chinese))
[23]	刘宁，朱维申，杨为民，等. 琅琊山抽水蓄能电站地下厂房开挖位移的智能反演[J]. 岩石力学与工程学报，2007，26(增2)：4 446- 4 451.(LIU Ning，ZHU Weishen，YANG Weimin，et al. Intelligent inversion of excavation displacement for underground powerhouse of Langyashan pumped-storage power station[J]. Chinese Journal of Rock Mechanics and Engineering，2007，26(Supp.2)：4 446-4 451.(in Chinese))
[24]	黄润秋，刘卫华. 基于正交设计的滚石运动特征现场试验研究[J]. 岩石力学与工程学报，2009，28(5)：882-891.(HUANG Runqiu，LIU Weihua. In-situ test study of characteristic of rolling rock blocks based on orthogonal design[J]. Chinese Journal of Rock Mechanics and Engineering，2009，28(5)：882-891.(in Chinese))
[25]	Itasca Consulting Group，Inc.. 3DEC three-dimensional distinct element code(Version 4.1)[R]. [S.l.]：Itasca Consulting Group，Inc.，2007.
[26]	CUNDALL P A. A computer model for simulation progressive large-scale movements in blocky rock system[C]// Proceedings of the International Symposium Rock Fracture，ISPM. [S.l.]：[s.n.]，1971：129-136.
[27]	LEMOS J V，HART R D，CUNDALL P A. A generalized distinct element program for modeling jointed rock mass[C]// Proceedings of the International Symposium on Fundamentals of Rock Joints. Bjorkliden，Sweden：[s.n.]，1985：335-343.
[28]	CUNDALL P A. Formulation of a three-dimensional distinct element model—part 1. A scheme to detect and represent contacts in a system composed of many polyhedral blocks[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstract，1988，25(3)：107-116.
[29]	HART R，CUNDALL P A，LEMOS J. Foundation of a three dimensional distinct element model—Part 2. Mechanical calculation for motion and interaction of a system composed of many polyhedral blocks[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstract，1988，25(3)：117-126.
[30]	王泳嘉，邢纪波. 离散单元法及其在岩土力学中的应用[M]. 沈阳：东北工学院出版社，1991：4-7.(WANG Yongjia，XING Jibo. Distinct element method and its application on rock and soil mechanics[M]. Shenyang：Northeast University of Technology Press，1991：4-7.(in Chinese))
[31]	殷跃平. 重庆武隆“6·5”山体崩滑及地灾防治的启示[R]. 北京：中国地质调查局，2010.(YIN Yueping. Chongqing Wulong “6·5”mountain landslides and inspiration to disaster prevention[R]. Beijing：China Geological Survey，2010.(in Chinese))
[32]	侯化国，王玉民. 正交试验法[M]. 长春：吉林人民出版社，1985：176-180.(HOU Huaguo，WANG Yumin. Orthogonal testing method[M]. Changchun：Jilin People¢s Publishing House，1985：176-180.(in Chinese))
[33]	刘文卿. 实验设计[M]. 北京：清华大学出版社，2005：13-29.(LIU Wenqing. Experiment design[M]. Beijing：Tsinghua University Press，2005：13-29.(in Chinese))
[34]	葛云峰，唐辉明，黄磊，等. 岩体结构面三维粗糙度系数表征新方法[J]. 岩石力学与工程学报，2012，31(12)：2 508-2 517.(GE Yunfeng，TANG Huiming，HUANG Lei，et al. A new representation method for three-dimensional joint roughness coefficient of rock joint[J]. Chinese Journal of Rock Mechanics and Engineering，2012，31(12)：2 508-2 517.(in Chinese))
[35]	TANG H M，GE Y F，WANG L Q，et al. Study on estimation method of rock mass discontinuity shear strength based on three-dimensional laser scanning and image technique[J]. Journal of Earth Science，2012，23(6)：908-913.