基于外锚头段切向刚度的在役锚索预应力测试方法研究

doi:10.13722/j.cnki.jrme.2021.1265

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (1091 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要为掌握在役预应力锚索的预应力状态，基于切向刚度理论，考虑工作状态下预应力锚索外锚头段结构传递效应，建立一种新的锚索预应力测试模型，并采用静载与动载试验进行验证。模型将外锚头段锚具与锚垫板间粗糙接触界面简化为锚固–接触模型，基于Hertz接触理论及GW统计接触模型，将锚索预应力的测量转化为对接触面切向接触刚度的识别，利用测量得到的切向荷载与切向位移，给出确定性的外锚头段切向刚度与锚索预应力值计算公式。静载与动载验证试验表明，得到的切向刚度与预应力试验值与理论值的平均相对误差为7.41%，使用弹性波为检测媒介得到的切向刚度与预应力试验值与理论值的平均相对误差也在10%之内，证实外锚头锚固–接触模型的正确性与切向刚度测力方法的可行性。该测试方法为在役锚索预应力检测提供了一种新的有效且无损的检测手段。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	陈强1
	周志鸿2
	朱宝龙3

关键词 ：岩土工程, 锚索, 预应力测试, 外锚头, 切向刚度

Abstract：To investigate the prestress state of prestressed anchor cables in service，a new prestress test model was established. This model is based on tangential stiffness theory and considering the structural transfer effect of external anchor segment under working condition，and verified by static and dynamic loading tests. By simplifying the rough contact interface between the anchor and anchor base plate of the external head segment as an anchorage-contact model，and based on Hertz contact theory and GW statistical contact model，this test model transforms the measurement of cable?s prestress into the identification of the tangential contact stiffness of the contact surface，then obtains the quantitative tangential stiffness of the external anchor segment and the calculating formula of anchor cable prestress，from the measured tangential load and displacement. The static and dynamic loading tests indicat that，the average relative error between the experimental and theoretical values of tangential stiffness and prestress is 7.41%，while this error is within 10% by measuring through elastic wave. These results support the correctness of the anchorage-contact model at external anchor head segment，and the feasibility of the tangential stiffness test method. This test method provides a new effective and nondestructive measurement for the prestress of anchor cables in service.

Key words： geotechnical engineering anchor cable prestress test external anchor head segment tangential stiffness

引用本文:

陈强1，周志鸿2，朱宝龙3. 基于外锚头段切向刚度的在役锚索预应力测试方法研究[J]. 岩石力学与工程学报, 2022, 41(8): 1595-1609.
CHEN Qiang1，ZHOU Zhihong2，ZHU Baolong3. Study on prestress test on in-service anchor cables based on tangential stiffness of external anchor head segment. , 2022, 41(8): 1595-1609.

链接本文:

http://rockmech.whrsm.ac.cn/CN/10.13722/j.cnki.jrme.2021.1265 或 http://rockmech.whrsm.ac.cn/CN/Y2022/V41/I8/1595

[4]	程良奎，张培文，王帆. 岩土锚固工程的若干力学概念问题[J]. 岩石力学与工程学报，2015，34(4)：668–682.(CHENG Liangku，ZHANG Peiwen，WANG Fan. Several mechanical concepts for anchored structures in rock and soil[J]. Chinese Journal of Rock Mechanics and Engineering，2015，34(4)：668–682.(in Chinese))
[6]	刘泉声，雷广峰，彭星新. 深部裂隙岩体锚固机制研究进展与思考[J]. 岩石力学与工程学报，2016，35(2)：312–332.(LIU Quansheng，LEI Guangfeng，PENG Xingxin. Advance and review on the anchoring mechanism in deep fractured rock mass[J]. Chinese Journal of Rock Mechanics and Engineering，2016，35(2)：312–332.(in Chinese))
[8]	沈俊，陈安敏，张向阳，等. 锚杆(索)抗动载加固技术研究进展[J].防护工程，2017，39(1)：63–71.(SHEN Jun，CHEN Anmin，ZHANG Xiangyang，et al. The research and development in geotechnical engineering reinforcement technique under dynamic load[J]. Protective Engineering，2017，39(1)：63–71.(in Chinese))
[14]	WANG M L，CHEN Z L，KOONTZ S S，et al. Magnetoelastic method of stress monitoring in steel tendons and cables[J]. Proceedings of SPIE，2000，16(6)：705–711.
[16]	SHISHIR G，NEELIMA B. Implementation of finite difference approximation on the SH-wave propagation in a multilayered magnetoelastic orthotropic composite medium[J]. Acta Mechanica，2017，228(10)：3 421–3 444.
[18]	董传智，郭伶，庞国英，等. 基于磁弹效应的体内预应力筋全量应力监测：实验研究与工程应用[J]. 结构工程师，2016，32(4)：74–79.(DONG Chuanzhi，GUO Ling，PANG Guoying，et al. Elasto-magnetic effect based total stress monitoring of internal prestressing tendons：experimental investigation and engineering application[J]. Structural Engineers，2016，32(4)：74–79.(in Chinese))
[34]	GREENWOOD J，WILLIAMSON J. Contact of nominally flat surfaces[J]. Proceedings of the Royal Society of London(A)，1966，295：300–319.
[24]	田北平，吴佳晔，刘文方，等. 预应力锚杆张力无损检测方法影响因素及最优测试组合方式探究[J]. 四川理工学院学报：自然科学版，2011，24(5)：561–563.(TIAN Beiping，WU Jiaye，LIU Wenfang，et al. Research on the influence factors and the optimal test combination of the non-destructive testing methods of prestressed bolt tension[J]. Journal of Sichuan University of Science and Engineering：Natural Science，2011，24(5)：561–563.(in Chinese))
[26]	钟新谷，杨滔，沈明燕，等. 混凝土箱梁桥腹板竖向预应力筋张拉力检测方法[J]. 中国公路学报，2010，23(4)：63–69.(ZHONG Xingu，YANG Tao，SHEN Mingyan，et al. Method for tension test of vertical prestressing bars in webs of concrete box girder bridges[J]. 2010，23(4)：63–69.(in Chinese))
[28]	王刚. 预应力锚固结构接触界面切向刚度问题研究[硕士学位论文][D]. 湘潭：湖南科技大学，2014.(WANG Gang. Study on tangential stiffness of contact interface of prestressed anchorage structure[M. S. Thesis][D]. Xiangtan：Hunan University of Science and Technology，2014.(in Chinese))
[36]	BERTHOUD P，BAUMBERGER T. Shear stiffness of a solid-solid multicontact interface[J]. Proceedings of the Royal Society of London. Series A：Mathematical，Physical and Engineering Sciences，1998，454(1974)：1 615–1 634.
[38]	SCHULTZ R. Design simulations for a combined shaker-acoustic vibration test technique[J]. The Journal of the Acoustical Society of America，2019，146(4)：3 079.
[1]	康红普，姜铁明，高富强. 预应力在锚杆支护中的作用[J]. 煤炭学报，2007，32(7)：680–685.(KANG Hongpu，JIANG Tieming，GAO Fuqiang. Effect of pretensioned stress to rock bolting[J]. Journal of China Coal Society，2007，32(7)：680–685.(in Chinese))
[11]	张峰，高磊，徐向锋，等. 施工期钢绞线锚下有效预应力测试技术[J]. 东北大学学报：自然科学版，2017，38(8)：1 201–1 205. (ZHANG Feng，GAO Lei，XU Xiangfeng，et al. Testing technology of under- anchorage effective prestress of steel strand in construction period[J]. Journal of Northeastern University：Natural Science，2017，38(8)：1 201–1 205.(in Chinese))
[21]	宋波，王华，张旭辉，等. 某山区超宽混凝土斜拉桥荷载试验检测技术研究[J]. 公路工程，2021，46(3)：68–73.(SONG Bo，WANG Hua，ZHANG Xuhu，et al. Experimental study on the technology of load test and detection for a super wide concrete cablestayed bridge in a mountainous area[J]. Highway Engineering，2021，46(3)：68–73.(in Chinese))
[23]	田北平，吴佳晔，季文洪，等. 不同预应力下锚头振动特性的测试分析[J]. 四川理工学院学报：自然科学版，2010，23(1)：4–6.(TIAN Beiping，WU Jiaye，JI Wenhong，et al. Numerical simulation and test analysis of the anchorage vibration characteristic under different prestressed[J]. Journal of Sichuan University of Science and Engineering：Natural Science，2010，23(1)：4–6.(in Chinese))
[25]	吴佳晔. 等效质量法在锚下有效预应力检测中的应用[J]. 铁道建筑，2017，(7)：1–4.(WU Jiaye. Application of equivalent mass method in inspection of effective prestress under anchorage[J]. Railway Engineering，2017，(7)：1–4.(in Chinese))
[27]	杨滔，钟新谷，沈明燕. PC箱梁桥腹板竖向预应力筋外露段频率特性的实验研究[J]. 振动与冲击，2011，30(12)：201–204.(YANG Tao，ZHONG Xingu，SHEN Mingyan. Test for frequency of uncased part of vertical tendon in webs of a prestressed concrete box girder bridge[J]. Journal of Vibration and Shock，2011，30(12)：201–204.(in Chinese))
[30]	郭俊平，狄彦强，左勇志，等. 既有预应力检测及某预应力钢筋混凝土框架加固修复方案研究[J]. 建筑结构，2020，50(24)：80–84.(GUO Junping，DI Yanqiang，ZUO Yongzhi，et al. Research on existing prestress detection and reinforcement and repair scheme of a prestressed reinforced concrete frame[J]. Building Structure，2020，50(24)：80–84.(in Chinese))
[31]	朱本珍，王建松，郑静，等. 锚索长期工作性能检测与荷载补偿技术研究[J]. 岩土力学，2011，32(增2)：683–685.(ZHU Benzhen，WANG Jiansong，ZHENG Jing，et al. Study of anchor cable long-term performance testing and load compensation[J]. Rock and Soil Mechanics，2011，32(Supp.2)：683–685.(in Chinese))
[35]	SNEDDON I N. Boussinesq?s problem for a rigid cone[J]. Mathematical Proceedings of the Cambridge Philosophical Society，1948，44(4)：492–507.
[37]	田红亮，陈从平，方子帆，等. 应用改进分形几何理论的结合部切向刚度模型[J]. 西安交通大学学报，2014，48(7)：46–52.(TIAN Hongliang，CHEN Congping，FANG Zifan，et al. Tangential stiffness model for joint interface adopting the revised fractal geometric theory[J]. Journal of Xi?an Jiaotong University，2014，48(7)：46–52.(in Chinese))
[2]	姜华. 微型桩–锚索联合支护顺层岩质边坡的稳定性分析[J]. 铁道科学与工程学报，2019，16(9)：2 184–2 191.(JIANG Hua. Stability analysis of bedding rock slope reinforced by micro-piles and prestressed anchor[J]. Journal of Railway Science and Engineering，2019，16(9)：2 184–2 191.(in Chinese))
[3]	康红普. 我国煤矿巷道锚杆支护技术发展60年及展望[J]. 中国矿业大学学报，2016，45(6)：1 071–1 081.(KANG Hongpu. Sixty years development and prospects of rock bolting technology for underground coal mine roadways in China[J]. Journal of China University of Mining and Technology，2016，45(6)：1 071–1 081.(in Chinese))
[5]	何依杰. 大跨径预应力混凝土连续梁桥病害成因分析探究实践[J].建筑技术开发，2021，48(3)：123–124.(HE Yijie. Exploration and practice of disease cause analysis of long-span prestressed concrete continuous beam bridge[J]. Building Technology Development，2021，48(3)：123–124.(in Chinese))
[7]	周永江，何思明，杨雪莲. 预应力锚索的预应力损失机制研究[J]. 岩土力学，2006，27(8)：1 353–1 356.(ZHOU Yongjiang，HE Siming，YANG Xuelian. Study on prestress loss of anchor cables under long-term loading[J]. Rock and Soil Mechanics，2006，27(8)：1 353–1 356. (in Chinese))
[9]	郭琦. 复杂预应力体系梁式结构有效预应力预测理论与方法研究[博士学位论文][D]. 西安：长安大学，2008.(GUO Qi. Study on the theory and method of effective prestress prediction for beam-type structures with complex prestressed systems[Ph. D. Thesis][D]. Xi?an：Chang?an University，2008.(in Chinese))
[10]	YANG S H，XU Z F，BIAN Z N. Prediction on compressive strength concrete using modified pull-off testing method(MPTM)[J]. Construction and Building Materials，2020，250：118834.
[12]	邓东平，李亮，赵炼恒. 2种应力波信号增强方式在预应力锚杆(索)锚固质量检测中的适用性研究[J]. 中南大学学报：自然科学版，2016，47(3)：936–945.(DENG Dongping，LI Liang，ZHAO Lianheng. Applicability of two stress wave signal enhancement modes in anchorage quality testing of pre-stressed anchor(cable)[J]. Journal of Central South University：Science and Technology，2016，47(3)：936–945.(in Chinese))
[13]	LI C，XIAO J，GUO T T，et al. Effects of graphene membrane parameters on diaphragm-type optical fibre pressure sensing characteristics[J]. Materials Research Innovations，2015，19(Supp.5)：17–23.
[15]	WANG M L，LLOYD G，HOVORKA O. Development of a remote coil magneto-elastic stress sensor for steel cables[C]// SPIE 8th Annual International Symposium on Smart Structures and Material，Health Monitoring and Management of Civil Infrastructure Systems，Newport Beach CA. [S. l.]：[s. n.]，2001：122–128.
[17]	SINGH A K，MISTRI K C，CHATTOPADHYAY A. Normal load moving on magneto-elastic transversely isotropic half-space with irregular and hydrostatic initial stress[J]. Journal of Vibration and Control，2017，23(8)：1–20.
[19]	BARTOLI I，SALAMNE S，PHILLIPS R，et al. Use of interwire ultrasonic leakage to quantify loss of prestress in multiwire tendons[J]. Journal of Engineering Mechanics，2011，137(5)：324–333.
[20]	CHEN C C，WU W H，LEU M R，et al. Tension determination of stay cable or external tendon with complicated constraints using multiple vibration measurements[J]. Measurement，2016，86：182–195.
[22]	LEI M，LI W J，LUO M Z，et al. An automatic extraction algorithm for measurement of installed rock bolt length based on stress wave reflection[J]. Measurement，2018，122：563–572.
[33]	HERTZ H. On the contact of elastic solids[J]. Crelle?s Journal，1881，92：156–171.
[29]	郭明渊，陈志华，刘红波，等. 拉索索力测试技术与抗弯刚度研究进展[J]. 空间结构，2016，22(3)：34–43.(GUO Mingyuan，CHEN Zhihua，LIU Hongbo，et al. Research progress of cable force test technology and cable flexural rigidity[J]. Spatial Structures，2016，22(3)：34–43.(in Chinese))
[32]	SNEDDON I N. The elastic stresses produced in a thick plate by the application of pressure to its free surfaces[J]. Mathematical Proceedings of the Cambridge Philosophical Society，1946，42(3)：260–271.
[39]	KIRSANOVA V N. The shear compliance of flat joints[J]. Machines and Tooling，1967，38：30–34.