基于形貌全覆盖的岩石结构面抗剪强度尺寸效应试验研究

doi:10.13722/j.cnki.jrme.2022.1228

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (2503 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要岩石结构面抗剪强度具有尺寸效应已成为学术与工程界共识，但现有理论和数值研究表明岩石结构面抗剪强度可能具有正尺寸效应、负尺寸效应或无尺寸效应的变化规律，由于结构面抗剪强度尺寸效应试验的难度大、费用高、周期长，造成系列尺寸结构面直剪试验较少，特别是对于起伏形貌全覆盖的系列尺寸(100～600 mm)结构面直剪试验研究还未见报道。基于Barton典型形貌曲线，采用多尺寸结构面一体化模具制作16组系列多尺寸结构面试样，通过自主研发的岩体结构面抗剪强度尺寸效应试验系统开展起伏形貌全覆盖的系列多尺寸结构面直剪试验，并采用三维全场应变测量系统(DIC)开展试验全过程非接触动态变形测量。研究结果表明：(1) 形貌全覆盖系列尺寸结构面峰值抗剪强度上渐近线呈现负尺寸效应规律，下渐近线呈现正尺寸效应规律，尺寸效应呈现的具体规律与取样位置及起伏形貌特征相关。(2) 不同尺寸试样同一形貌特征结构面会产生剪断、爬坡、耦合等不同剪切破坏模式；相同尺寸试样不同形貌特征结构面的剪切破坏模式也有差异，且表面形貌起伏程度越大其应变增长越快。(3) 尺寸越大，具有较大起伏形貌特征的结构面剪应力与剪位移曲线峰值特征越明显；尺寸越小，具有较大起伏形貌特征的结构面峰值抗剪强度离散性越大。(4) 基于等权重系数法开展了大尺寸结构面峰值抗剪强度评价，Grasselli公式计算峰值抗剪强度加权评价值与实测值相比误差较大。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	罗战友1
	2
	黄斌1
	杜时贵2
	黄曼1
	吕原君2
	刘广建1

关键词 ：岩石力学, 岩石结构面, 抗剪强度, 尺寸效应, 直剪试验, 起伏形貌

Abstract：Size effect of shear strength of rock joints has become the consensus of academic and engineering circles，but the existing theoretical and numerical studies show that the shear strength of rock joints may have positive size effect，negative size effect or no size effect. Due to the difficulty，high cost and long period of size effect test of shear strength of rock joints，there are few direct shear tests of joints with series size，especially for full-coverage direct shear test of rock joints with fluctuation morphology in a series of sizes(100–600 mm). In this paper，based on Barton's typical morphology curves，16 sets of multi-scale joint samples were made by multi-scale joint integration mold. The direct shear test of a series of multi-scale joints with full coverage of fluctuation morphology was carried out through the self-developed shear strength size effect test system of rock joints，and non-contact dynamic deformation measurement of the whole test process was carried out by DIC. The results show that：(1) Upper asymptote of peak shear strength of rock joint exhibits a negative size effect law，and lower asymptote exhibits a positive size effect law. The specific pattern of size effect is related to the sampling position and fluctuation morphology characteristics. (2) Different shear failure modes such as shear，climbing and coupling will occur in the same morphology of rock joints with different sizes. The shear failure modes of joints with different morphology characteristics of the same size samples are also different，and the larger the fluctuation degree of surface morphology，the faster the strain growth. (3) The larger the size，the more obvious the peak characteristics of shear stress and shear displacement curves of rock joint with large fluctuation morphology；the smaller the size，the larger the discreteness of peak shear strength of rock joint with large fluctuation morphology. (4) Based on the equal weight coefficient method，peak shear strength evaluation of large-scale rock joint is carried out. The weighted evaluation value of peak shear strength calculated by Grasselli formula has a large error compared with the measured value.

Key words： rock mechanics rock joint shear strength size effect direct shear test fluctuation morphology

引用本文:

罗战友1，2，黄斌1，杜时贵2，黄曼1，吕原君2，刘广建1. 基于形貌全覆盖的岩石结构面抗剪强度尺寸效应试验研究[J]. 岩石力学与工程学报, 2024, 43(2): 287-297.
LUO Zhanyou1，2，HUANG Bin1，DU Shigui2，HUANG Man1，LYU Yuanjun2，LIU Guangjian1. Experimental study on size effect of shear strength of rock joints. , 2024, 43(2): 287-297.

链接本文:

http://rockmech.whrsm.ac.cn/CN/10.13722/j.cnki.jrme.2022.1228 或 http://rockmech.whrsm.ac.cn/CN/Y2024/V43/I2/287

[6]	HENCHER S R，TOY J P，LUMSDEN A C. Scale-dependent shear strength of rock joints[C]// Proceedings of the 2nd International Workshop on Scale Effects in Rock Masses. Rotterdam：A A Balkema，1993：233-240
[16]	MURALHA J，GRASSELLI G，TATONE B，et al. ISRM Suggested method for laboratory determination of the shear strength of rock joints：revised version[J]. Rock Mechanics and Rock Engineering，2014，47(1)：291-302.
[23]	BARTON N. Review of a new shear-strength criterion for rock joints[J]. Engineering Geology，1973，7(4)：287-332.
[1]	DU S G，LIN H，YONG R，et al. Characterization of joint roughness heterogeneity and its application in representative sample investigations[J]. Rock Mechanics and Rock Engineering，2022，55(6)：3 253-3 277.
[3]	杜时贵，吕原君，罗战友，等. 岩体结构面抗剪强度尺寸效应联合试验系统及初级应用研究[J]. 岩石力学与工程学报，2021，40(7)：1 337-1 349.(DU Shigui，LV Yuanjun，LUO Zhanyou，et al. Combined test system for size effect of rock joint shear strength and its primary application research[J]. Chinese Journal of Rock Mechanics and Engineering，2021，40(7)：1 337-1 349.(in Chinese))
[5]	葛云峰，唐辉明，王亮清，等. 天然岩体结构面粗糙度各向异性，尺寸效应，间距效应研究[J]. 岩土工程学报，2016，38(1)：170-179.(GE Yunfeng，TANG Huiming，WANG Liangqing，et al. Anisotropy，scale and interval effects of natural rock discontinuity surface roughness[J]. Chinese Journal of Geotechnical Engineering，2016，38(1)：170-179.(in Chinese))
[7]	OHNISHI Y，YOSHINAKA R. Laboratory investigation of scale effect in mechanical behavior of rock[C]// Proceedings of the Conference on Fractured and Jointed Rock Masses. Rotterdam：A A Balkema，1992：465-477.
[9]	谷德振. 岩体工程地质力学基础[M]. 北京：科学出版社，1979：250-252.(GU Dezhen. Geomechanics foundation of rock engineering[M]. Beijing：Science Press，1979：250-252.(in Chinese))
[11]	BANDIS S，LUMSDEN A，BARTON N. Experimental studies of scale effects on the shear behaviour of rock joints[J]. International Journal of Rock Mechanics and Mining Science and Geomechanics Abstracts，1981，18(1)：1-21.
[13]	CASTELLI M，SAVIA S，ZANINETI A. Experimental evaluation of scale effect on the mechanical behavior of rock joints[C]// Proceedings of International Eurock Symposium. Espoo，Finland：[s. n.]，2001：205-210.
[10]	孙广忠. 岩体结构力学[M]. 北京：科学出版社，1988：188-189.(SUN Guangzhong. Structural mechanics of rock mass[M]. Beijing：Science Press，1988：188-189.(in Chinese))
[8]	BARTON N，CHOUBEY V. The shear strength of rock joints in theory and practice[J]. Rock Mechanics，1977，10(1)：1-54.
[15]	黄曼，杜时贵，罗战友，等. 基于多尺度直剪试验的岩石模型结构面抗剪强度特征研究[J]. 岩土力学，2013，34(11)：3 180-3 186. (HUANG Man，DU Shigui，LUO Zhanyou，et al. Study of shear strength characteristics of simulation rock joints based on multi-size direct shear tests[J]. Rock and Soil Mechanics，2013，34(11)：3 180-3 186.(in Chinese))
[17]	HENCHER S R，RICHARDS L R. Assessing the shear strength of rock discontinuities at laboratory and field scales[J]. Rock Mechanics and Rock Engineering，2014，48(3)：883-905.
[18]	BAHAADDINI M，HAGAN P C，MITRA R，et al. Scale effect on the shear behaviour of rock joints based on a numerical study[J]. Engineering Geology，2014，181：212-223.
[19]	乐慧琳，吴继敏，高晓兵，等．尺寸效应对锯齿状结构面抗剪强度影响[J]. 辽宁工程技术大学学报：自然科学版，2016，35(7)：745-750.(LE Huilin，WU Jimin，GAO Xiaobing，et al. Influence of size effect on shearing strength of zig-zag structure plane[J]. Journal of Liaoning Technical University：Natural Science，2016，35(7)：745-750.(in Chinese))
[21]	黄曼，夏才初，马成荣，等. 系列尺度岩体结构面形貌渐进覆盖统计方法[J]. 岩石力学与工程学报，2019，38(8)：1 533-1 541. (HUANG Man，XIA Caichu，MA Chengrong，et al. A progressive coverage statistical method for series scale surface morphology of rock joints[J]. Chinese Journal of Rock Mechanics and Engineering，2019，38(8)：1 533-1 541.(in Chinese))
[25]	GRASSELLI G，EGGER P. Constitutive law for the shear strength of rock joints based on three-dimensional surface parameters[J]. International Journal of Rock Mechanics and Mining Sciences，2003，40(1)：25-40.
[2]	罗战友，杜时贵，黄曼. 岩石结构面峰值摩擦角应力效应试验研究[J]. 岩石力学与工程学报，2014，33(6)：1 142-1 148.(LUO Zhanyou，DU Shigui，HUANG Man. Experimental study of stress effection peakfriction angle of rock joint[J]. Chinese Journal of Rock Mechanics and Engineering，2014，33(6)：1 142-1 148.(in Chinese))
[4]	王培涛，任奋华，蔡美峰. 基于离散元方法的粗糙性节理岩体直剪力学及尺寸效应特性[J]. 煤炭学报，2018，43(4)：976-983.(WANG Peitao，REN Fenghua，CAI Meifeng. Mechanical analysis and size effect of rough discrete fractures network model under direct shear tests based on particle flow code[J]. Journal of China Coal Society，2018，43(4)：976-983.(in Chinese))
[12]	YOSHINAKA R，YOSHIDA J，ARAI H，et al. Scale effect in shear strength and deformation of rock joints[C]// Proceedings of the 7th ISRM Conference. Aachen，Germany：[s. n.]，1991：371-378.
[14]	OHNISHI Y，HERDA H，YOSHINAKA R. Shear strength scale effect and the geometry of single and repeated rock joints[C]// Proceedings of the 2nd International Conference on Scale Effect in Rock Masses. Lisbon，Portugal：[s. n.]，1993：167-173.
[22]	MURALHA J，GRASSELLI G，TATONE B，et al. ISRM suggested method for laboratory determination of the shear strength of rock joints：Revised version[J]. Rock Mechanics and Rock Engineering，2014，47：291-302.
[24]	唐正宗，梁晋，肖振中，等. 用于三维变形测量的数字图像相关系统[J]. 光学精密工程，2010，18(10)：2 244-2 253.(TANG Zhengzong，LIANG Jin，XIAO Zhenzhong，et al. Digital image correlation system for three-dimensional deformation measurement[J]. Optics and Precision Engineering，2010，18(10)：2 244-2 253.(in Chinese))
[20]	陈世江，高臻炜，谷运峰，等. 类岩体结构面峰值剪切强度尺寸效应分析[J]. 矿业研究与开发，2021，41(4)：88-95.(CHEN Shijiang，GAO Zhenwei，GU Yunfeng，et al. Size effect analysis on peak shear strength of rock-like structure interface[J]. Mining Research and Development，2021，41(4)：88-95.(in Chinese))