拉应力作用下黑砂岩剪切破裂面粗糙度表征及各向异性特征研究

doi:10.13722/j.cnki.jrme.2019.1019

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (2022 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要地下洞室围岩开挖卸荷常发生张拉、剪切等破坏模式。为研究不同破坏模式对岩石破裂面形貌特征的影响，基于黑砂岩直接拉伸与拉伸剪切试验，通过引入二维、三维粗糙度评价指标，定量表征岩石破裂面的形貌特征，获得了拉应力作用下岩石破裂面粗糙度随应力状态的变化规律，简要探讨了不同破裂机制对破裂面形貌影响。研究发现各类粗糙度评价指标均随拉应力的增大而呈线性减小趋势。同时，基于各向异性特征参数的度量，相比二维粗糙度评价指标，三维评价指标更能准确表征岩石破裂面的粗糙特性，其与拉应力之间呈指数型变化关系。对于直接拉伸试验，岩石破裂面形貌差异最小；而对于拉伸剪切试验，随着拉应力的减小，破裂面各向异性程度逐渐增大。研究结果表明不同的岩石破坏模式和破裂机制是造成破裂面形貌特征具有差异性的根本原因。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	陈珺1
	周辉2
	3
	侯靖1
	卢景景2
	3
	张传庆2
	3
	崔国建2
	3
	倪绍虎1

关键词 ：岩石力学, 拉伸剪切试验, 完整岩石, 粗糙度指标, 各向异性

Abstract：Excavation and unloading from surrounding rock of underground caverns often cause failure modes such as tension and shear. In order to study the influence of different failure modes on the morphological characteristics of rock fracture surface，the direct tensile test and tension-shear test of black sandstone are carried out，and the two-dimensional and three-dimensional evaluation index are introduced to quantitatively characterize the rock fracture surface. The morphological characteristics of the rock fracture surface under the tensile stress are obtained，and the effects of different rupture mechanisms on the morphological characteristics of the fracture surface are briefly discussed. It is found that all kinds of roughness evaluation indexes decrease linearly with the increase in tensile stress. At the same time，based on the measurement of the anisotropic characteristic parameter ，the three-dimensional roughness evaluation index can accurately characterize the roughness of the rock fracture surface compared with the two-dimensional index ，and it has an exponential relationship to the tensile stress. For the direct tensile test，the difference in the morphology of the rock fracture surface is the smallest；for the tension-shear test，the degree of anisotropy of the fracture surface gradually increases to the decrease of the tensile stress. The results show that different rock failure modes and rupture mechanisms are the root causes of the differences in the morphology of the fracture surface.

Key words： rock mechanics tension-shear test intact rock roughness index anisotropy

引用本文:

陈珺1，周辉2，3，侯靖1，卢景景2，3，张传庆2，3，崔国建2，3，倪绍虎1. 拉应力作用下黑砂岩剪切破裂面粗糙度表征及各向异性特征研究[J]. 岩石力学与工程学报, 2020, 39(S1): 2623-2633.
CHEN Jun1，ZHOU Hui2，3，HOU Jing1，LU Jingjing2，3，ZHANG Chuanqing2，3，CUI Guojian2，3，NI Shaohu1. Study on anisotropic and roughness characteristics of shear fracture surface of black sandstone under tensile stress. , 2020, 39(S1): 2623-2633.

链接本文:

http://rockmech.whrsm.ac.cn/CN/10.13722/j.cnki.jrme.2019.1019 或 http://rockmech.whrsm.ac.cn/CN/Y2020/V39/IS1/2623

[34]	BARTON N，BANDIS S. Effects of block size on the shear behavior of jointed rock[J]. The 23rd US Symposium on Rock Mechanics，Berkeley，1982：739–760.
[2]	周辉，张凯，冯夏庭，等. 脆性大理岩弹塑性耦合力学模型研究[J]. 岩石力学与工程学报，2010，29(12)：2 398–2 409.(ZHOU Hui，ZHANG Kai，FENG Xiating，et al. Elastoplastic coupling mechanical model for brittle marble[J]. Chinese Journal of Rock Mechanics and Engineering，2010，29(12)：2 398–2 409.(in Chinese))
[12]	张桂民，李银平，杨春和，等. 岩石直剪峰后曲线与抗剪强度参数关系探讨[J]. 岩石力学与工程学报，2012，31(增1)：2 981–2 988.(ZHANG Guimin，LI Yinping，YANG Chunhe，et al. Discussion on relationship between post-peak curves and shear strength parameters of rocks subjected to direct shear tests[J]. Chinese Journal of Rock Mechanics and Engineering，2012，31(Supp.1)：2 981–2 988.(in Chinese))
[16]	YANG J，RONG G，HOU D，et al. Experimental study on peak shear strength criterion for rock joints[J]. Rock Mechanics and Rock Engineering，2016，49(3)：821–835.
[26]	MYERS N O. Characterization of surface roughness[J]. Wear，1962，(5)：182–189.
[1]	王学潮，杨维九，刘丰收. 南水北调西线一期工程的工程地质和岩石力学问题[J]. 岩石力学与工程学报，2005，24(20)：3 603– 3 613.(WANG Xuechao，YANG Weijiu，LIU Fengshou. Engineering geology and rock mechanical problems in west route of south-to-north water transfer project[J]. Chinese Journal of Rock Mechanics and Engineering，2005，24(20)：3 603–3 613.(in Chinese))
[4]	侯哲生，龚秋明，孙卓恒. 锦屏二级水电站深埋完整大理岩基本破坏方式及其发生机制[J]. 岩石力学与工程学报，2011，30(4)：727–732.(HOU Zhesheng，GONG Qiuming，SUN Zhuoheng. Primary failure types and their failure mechanisms of deep buried and intact marble at Jinping II hydropower station[J]. Chinese Journal of Rock Mechanics and Engineering，2011，30(4)：727–732.(in Chinese))
[6]	陈炳瑞，冯夏庭，明华军，等. 深埋隧洞岩爆孕育规律与机制：时滞型岩爆[J]. 岩石力学与工程学报，2012，31(3)：561–569.(CHEN Bingrui，FENG Xiating，MING Huajun，et al. Evolution law and mechanism of rockbursts in deep tunnels：time delayed rockburst[J]. Chinese Journal of Rock Mechanics and Engineering，2012，31(3)：561–569.(in Chinese))
[8]	江权，樊义林，冯夏庭，等. 高应力下硬岩卸荷破裂：白鹤滩水电站地下厂房玄武岩开裂观测实例分析[J]. 岩石力学与工程学报，2017，36(5)：1 076–1 087.(JIANG Quan，FAN Yilin，FENG Xiating，et al. Unloading break of hard rock under high geo-stress condition：inner cracking observation for the basalt in the Baihetan’s underground powerhouse[J]. Chinese Journal of Rock Mechanics and Engineering，2017，35(5)：1 076–1 087.(in Chinese))
[11]	刘冬梅，谢锦平，周玉斌，等. 岩石压剪耦合破坏过程的实时监测研究[J]. 岩石力学与工程学报，2004，23(10)：1 616–1 620.(LIU Dongmei，XIE Jinping，ZHOU Yubin，et al. Real-time testing study of rock fracture under coupled compression and shear[J]. Chinese Journal of Rock Mechanics and Engineering，2004，23(10)：1 616–1 620.(in Chinese))
[14]	衡帅，杨春和，曾义金，等. 基于直剪试验的页岩强度各向异性研究[J]. 岩石力学与工程学报，2014，33(5)：874–883.(HENG Shuai，YANG Chunhe，ZENG Yijin，et al. Anisotropy of shear strength of shale based on direct shear test[J]. Chinese Journal of Rock Mechanics and Engineering，2014，33(5)：874–883.(in Chinese))
[41]	JIANG Q，FENG X T，GONG Y H，et al. Reverse modelling of natural rock joints using 3D scanning and 3D printing[J]. Computers and Geotechnics，2016，73：210–220.
[18]	王煜曦. 岩石断裂表面细观接触演化与剪切力学模型研究[博士学位论文][D]. 北京：北京科技大学，2015.(WANG Yuxi. Study on micro-contact evolution and shear mechanical model of fractured rock surfaces[Ph. D. Thesis][D]. Beijing：University of Science and Technology Beijing，2015.(in Chinese))
[22]	程广坦. 岩体结构面力学特性及其对深埋隧洞岩爆影响的试验研究[博士学位论文][D]. 武汉：中国科学院武汉岩土力学研究所，2018.(CHENG Guangtan. Experimental study on the mechanical characteristic of rockmass structural plane and it’s impact on rockburst in deep tunnel[Ph. D. Thesis][D]. Wuhan：Institute of Rock and Soil Mechanics，Chinese Academy of Sciences，2018.(in Chinese))
[24]	MAERZ N H，FRANKLIN J A，BENNETT C P. Joint roughness measurement using shadow profilometry[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts，1990，27(5)：329–343.
[29]	谢和平. 岩石节理的分形描述[J]. 岩土工程学报，1995，17(1)：18–22.(XIE Heping. Fractal description of rock joints[J]. Chinese Journal of Geotechnical Engineering，1995，17(1)：18–22.(in Chinese))
[28]	许宏发，李艳茹，刘新宇，等. 节理面分形模拟及JRC与分维的关系[J]. 岩石力学与工程学报，2002，21(11)：1 663–1 666.(XU Hongfa，LI Yanru，LIU Xinyu，et al. Fractal simulation of joint profiles and relationship between JRC and fractal dimension[J]. Chinese Journal of Rock Mechanics and Engineering，2002，21(11)：1 663–1 666.(in Chinese))
[32]	GRASSELLI G，WIRTHC J，EGGER P. Quantitative three- dimensional description of a rough surface and parameter evolution with shearing[J]. International Journal of Rock Mechanics and Mining Sciences，2002，39(6)：789–800.
[36]	AYDAN O，SHIMIZU Y，KAWAMOTO T. The anisotropy of surface morphology characteristics of rock discontinuities[J]. Rock Mechanics and Rock Engineering，1996，29(1)：47–59.
[25]	EI-SOUDANI S M. Profilometric analysis of fractures[J]. Metallography，1978，11(3)：247–336.
[38]	CHEN S J，ZHU W C，YU Q L，et al. Characterization of anisotropy of joint surface roughness and aperture by variogram approach based on digital image processing technique[J]. Rock Mechanics and Rock Engineering，2016，49(3)：855–876.
[42]	XIE H P，WANG J A. Direct fractal measurement of fracture surfaces[J]. International Journal of Solids and Structures，1999，36(20)：3 073–3 084.
[44]	KULATILAKE P H S W，PARK J，BALASINGAM P，et al. Quantification of aperture and relations between aperture，normal stress and fluid flow for natural single rock fractures[J]. Geotechnical and Geological Engineering，2008，26(3)：269–281.
[46]	陈世江，朱万成，刘树新，等. 岩体结构面粗糙度各向异性特征及尺寸效应分析[J]. 岩石力学与工程学报，2015，34(1)：57–66.(CHEN Shijiang，ZHU Wancheng，LIU Shuxin，et al. Anisotropy and size effects of surface roughness of rock joints[J]. Chinese Journal of Rock Mechanics and Engineering，2015，34(1)：57–66.(in Chinese))
[10]	孟凡震. 硬岩脆性破坏及结构面型岩爆发生机制的试验研究[博士学位论文][D]. 武汉：中国科学院武汉岩土力学研究所，2015.(MENG Fanzhen. Experimental study on brittle failure of hard rock and mechanism of rockburst induced by structural plane[Ph. D. Thesis][D]. Wuhan：Institute of Rock and Soil Mechanics，Chinese Academy of Sciences，2015.(in Chinese))
[20]	郭静芸. 岩石拉伸剪切变形破坏特征与破坏准则[硕士学位论文][D]. 北京：中国科学院地质与地球物理研究所，2013.(GUO Jingyun. Failure characteristics and criterion of rock in tension-shear state[M. S. Thesis][D]. Beijing：Institute of Geology and Geophysics，Chinese Academy of Sciences，2013.(in Chinese))
[30]	孙辅庭，佘成学，万利台. 新的岩石节理粗糙度指标研究[J]. 岩石力学与工程学报，2013，32(12)：2 513–2 519.(SUN Futing，SHE Chengxue，WAN Litai. Research on a new roughness index of rock joint[J].Chinese Journal of Rock Mechanics and Engineering，2013，32(12)：2 513–2 519.(in Chinese))
[40]	TATONE B S A，GRASSELLI G. A method to evaluate the three dimensional roughness of fracture surfaces in brittle geomaterials[J]. Review of Scientific Instruments，2009，80(12)：1–10.
[50]	陈忠辉，唐春安，傅宇方. 岩石微破裂损伤演化诱致突变的数值模拟[J]. 岩土工程学报，1998，20(6)：9–15.(CHEN Zhonghui，TANG Chun'an，FU Yufang. Infinite element simulation of catastrophe induced by evolution of rock micro fracturing damage[J]. Chinese Journal of Geotechnical Engineering，1998，20(6)：9–15.(in Chinese))
[3]	严健，何川，汪波，等. 雅鲁藏布江缝合带深埋长大隧道群岩爆孕育及特征[J]. 岩石力学与工程学报，2019，38(4)：769–781.(YAN Jian，HE Chuan，WANG Bo，et al. Inoculation and characters of rockbursts in extra-long and deep-lying tunnels located on Yarlung Zangbo suture[J]. Chinese Journal of Rock Mechanics and Engineering，2019，38(4)：769–781.(in Chinese))
[5]	冯夏庭，陈炳瑞，明华军，等. 深埋隧洞岩爆孕育规律与机制：即时型岩爆[J]. 岩石力学与工程学报，2012，31(3)：433–444.(FENG Xiating，CHEN Bingrui，MING Huajun，et al. Evolution law and mechanism of rockbursts in deep tunnels：immediate rockburst[J]. Chinese Journal of Rock Mechanics and Engineering，2012，31(3)：433–444.(in Chinese))
[7]	刘国锋，冯夏庭，江权，等. 白鹤滩大型地下厂房开挖围岩片帮破坏特征、规律及机制研究[J]. 岩石力学与工程学报，2016，35(5)：865–878.(LIU Guofeng，FENG Xiating，JIANG Quan，et al. Failure characteristics，laws and mechanisms of rock spalling in excavation of large-scale underground powerhouse caverns in Baihetan[J]. Chinese Journal of Rock Mechanics and Engineering，2016，35(5)：865–878.(in Chinese))
[9]	孟国涛，樊义林，江亚丽，等. 白鹤滩水电站巨型地下洞室群关键岩石力学问题与工程对策研究[J]. 岩石力学与工程学报，2016，35(12)：2 549–2 560.(MENG Guotao，FAN Yilin，JIANG Yali，et al. Key rock mechanical problems and measures for huge caverns of Baihetan hydropower plant[J]. Chinese Journal of Rock Mechanics and Engineering，2016，35(12)：2 549–2 560.(in Chinese))
[13]	范雷，周火明，熊诗湖. 现场岩体直剪试验声发射特征与其破坏机制[J]. 长江科学院报，2012，29(8)：29–32.(FAN Lei，ZHOU Huoming，XIONG Shihu. Acoustic emission characteristics and failure mechanism of rock mass in field shear test[J]. Journal of Yangtze River Scientific Research Institute，2012，29(8)：29–32.(in Chinese))
[15]	刘伟，曾亚武，夏磊，等. 正反向直剪下层状岩体强度和破坏特征模型试验[J]. 武汉大学学报：工学版，2019，52(7)：1–10.(LIU Wei，ZENG Yawu，XIA Lei，et al. Model tests for strength and failure characteristics of forward and reverse shear rock masses[J]. Engineering Journal of Wuhan University，2019，52(7)：1–10.(in Chinese))
[17]	MENG F，WONG L N Y，ZHOU H，et al. Shear rate effects on the post-peak shear behaviour and acoustic emission characteristics of artificially split granite joints[J]. Rock Mechanics and Rock Engineering，2019，52(7)：2 155–2 174.
[19]	郭静芸，李晓，李守定，等. 拉伸剪切条件下岩石的工程地质力学特性[J]. 工程地质学报，2012，20(6)：1 020–1 027.(GUO Jingyun，LI Xiao，LI Shouding，et al. The engineering geology mechanical properties of rock in tension-shear state[J]. Journal of Engineering Geology，2012，20(6)：1 020–1 027.(in Chinese))
[23]	陈世江，朱万成，王创业，等. 岩体结构面粗糙度系数定量表征研究进展[J]. 力学学报，2017，49(2)：239–256.(CHEN Shijiang，ZHU Wancheng，WANG Chuangye，et al. Review of research progresses of the quantifying joint roughness coefficient[J]. Chinese Journal of Theoretical and Applied Mechanics，2017，49(2)：239–256(in Chinese))
[33]	杜时贵，陈禹，樊良本. JRC修正直边法的数学表达[J]. 工程地质学报，1996，4(2)：36–43.(DU Shigui，CHEN Yu，FAN Lingben. Mathematical expression of JRC modified straight edge[J]. Journal of Engineering Geology，1996，4(2)：36–43.(in Chinese))
[35]	BELEM T，HOMAND-ETIENNE F，SOULEY M. Quantitative parameters for rock joint surface roughness[J]. Rock Mechanics and Rock Engineering，2000，33(4)：217–242.
[21]	周辉，陈珺，卢景景，等. 岩石多功能剪切试验测试系统研制[J]. 岩土工程，2018，39(3)：1 115–1 122.(ZHOU Hui，CHEN Jun，LU Jingjing，et al. Development of a multi-functional shear test system for rock[J]. Rock and Soil Mechanics，2018，39(3)：1 115–1 122.(in Chinese))
[27]	TSE R，CRUDEN D M. Estimating joint roughness coefficients[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts，1979，16(5)：303–307.
[37]	葛云峰，唐辉明，黄磊，等. 岩体结构面三维粗糙度系数表征新方法[J]. 岩石力学与工程学报，2012，31(12)：2 508–2 517.(GE Yunfeng，TANG Huiming，HUANG Lei，et al. A new representation method for three-dimensional joint roughness coefficient of rock joint[J]. Chinese Journal of Rock Mechanics and Engineering，2012，31(12)：2 508–2 517.(in Chinese))
[47]	陈世江，朱万成，王创业，等. 考虑各向异性特征的三维岩体结构面峰值剪切强度研究[J]. 岩石力学与工程学报，2016，35(10)： 2 013–2 021.(CHEN Shijiang，ZHU Wancheng，WANG Chuangye，et al. Peak shear strength of 3D rock discontinuities based on anisotropic properties [J]. Chinese Journal of Rock Mechanics and Engineering，2016，35(10)：2 013–2 021.(in Chinese))
[31]	陈世江，朱万成，张敏思，等. 基于数字图像处理技术的岩石节理分形描述[J]. 岩土工程学报，2012，34(11)：2 087–2 092.(CHEN Shijiang，ZHU Wancheng，ZHANG Minsi，et al. Fractal description of rock joint based on digital image processing technique[J]. Chinese Journal of Geotechnical Engineering，2012，34(11)：2 087–2 092.(in Chinese))
[39]	陈世江，朱万成，于庆磊，等. 基于多重分形特征的岩体结构面剪切强度研究[J]. 岩土力学，2015，36(3)：703–710.(Chen Shijiang，Zhu Wancheng，Yu Qinglei，et al. Shear strength research on rock joint surfaces based on multifractal theory[J]. Rock and Soil Mechanics，2015，36(3)：703–710.(in Chinese))
[49]	宋磊博，江权，李元辉，等. 不同点云数据采样间隔下岩石自然结构面形貌特征和各向异性特征的统计参数稳定性研究[J]. 岩土力学，2017，38(4)：1–13.(SONG Leibo，JIANG Quan，LI Yuanhui，et al. Study on the stability of statistical parameters of the rock nature discontinuities morphology and anisotropic based on different interval point-cloud data[J]. Rock and Soil Mechanics，2017，38(4)：1–13.(in Chinese))
[43]	KULATILAKE P H S W，BALASINGAM P，PARK J，et al. Natural rock joint roughness quantification through fractal techniques[J]. Geotechnical and Geological Engineering，2006，24(5)：1 181–1 202.
[45]	BELEM T，HOMAND ETLENNE F，SOULEY M. Quantitative parameter for rock joint surface roughness[J]. Rock Mechanics and Rock Engineering，2000，33(4)：217–242.
[48]	葛云峰，唐辉明，王亮清，等. 天然岩体结构面粗糙度各向异性、尺寸效应、间距效应研究[J]. 岩土工程学报，2016，38(1)：170–179.(GE Yunfeng，TANG Huiming，WANG Liangqing，et al. Anisotrop scale and interval effects of natural rock discontinuity surface roughness[J]. Chinese Journal of Geotechnical Engineering，2016，38(1)：170–179.(in Chinese))