深部原位应力煤岩卸荷力学特性试验研究

doi:10.13722/j.cnki.jrme.2023.0010

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (4766 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要为探究深部原位应力煤岩卸荷力学特性，利用MTS816岩石力学测试系统对原位应力煤岩开展不同卸荷速率的三轴加卸载试验，并与常规卸荷试验对比，通过获取全过程应力–应变曲线分析卸荷煤岩的力学性能与变形特征，结合CT三维重构技术研究煤岩的破坏特征，探讨原位应力卸荷煤岩的适用强度准则。结果表明：(1) 2种方案煤岩的峰值强度与卸荷速率均成反比，但原位应力煤岩较常规煤岩的峰值强度更高，这种趋势在低速卸荷时逐渐弱化。(2) 原位应力恢复过程实施后，煤岩在卸荷速率升高条件下，峰值轴向应变先减小后趋于稳定，峰值侧向应变整体不变，峰值体积应变先降低后增加。卸荷条件下原位应力煤岩的弹性模量更平稳，应变硬化模量得以增强。(3) Mogi-Coulomb强度准则能更好地反映原位卸荷煤岩的破坏强度特征；原位应力煤岩较常规煤岩的黏聚力c增加39.23%，内摩擦角减少11.92%，表明原位卸荷煤岩的抗破坏主控因素为黏聚力。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	王磊
	邹鹏
	谢广祥
	范浩
	陈礼鹏
	张宇

关键词 ：采矿工程, 煤岩, 原位应力, 卸荷速率, 力学特性, 破坏特征, 强度准则

Abstract：In order to research the mechanical properties of deep coal under in-situ unloading stresses，triaxial loading and unloading tests with different unloading rates were carried out on coal under in-situ stresses by using the MTS816 rock mechanics test system and compared with conventional unloading tests. The stress-strain curve was used to analyze the mechanical properties and deformation characteristics of unloaded coal. 3D reconstruction technology by CT was applied to study the failure characteristics of coal. With this prerequisite, the applicable strength criterion of in-situ coal was discussed. The results show that：(1) The peak strengths of coal with two schemes are inversely proportional to the unloading rate. However，the peak strength of in-situ coal is higher than that of conventional coal，and this trend gradually weakens during low-speed unloading. (2) After in-situ stress recovery， as the unloading rate increases， the peak axial strain of coal first decreases and then tends to stabilize，the peak lateral strain remains unchanged，and the peak volumetric strain first decreases and then increases. Under unloading conditions，the elastic modulus of in-situ coal under unloading condition is more stable，making the strain hardening modulus enhanced. (3) The Mogi-Coulomb strength criterion can better reflect the failure strength characteristics of in-situ unloading coal. The cohesion c of in-situ coal increases 39.23% and the internal friction angle decreases 11.92% compared with conventional coal，indicating that the main control factor of failure resistance of in-situ unloading coal is cohesion.

Key words： mining engineering coal rock in-situ stress unloading rate mechanical properties failure characteristics strength criterion

引用本文:

王磊，邹鹏，谢广祥，范浩，陈礼鹏，张宇. 深部原位应力煤岩卸荷力学特性试验研究[J]. 岩石力学与工程学报, 2023, 42(12): 2876-2887.
WANG Lei，ZOU Peng，XIE Guangxiang，FAN Hao，CHEN Lipeng，ZHANG Yu. Experimental study on unloading mechanical properties of deep coal under in-situ stresses. , 2023, 42(12): 2876-2887.

链接本文:

https://rockmech.whrsm.ac.cn/CN/10.13722/j.cnki.jrme.2023.0010 或 https://rockmech.whrsm.ac.cn/CN/Y2023/V42/I12/2876

[1]	齐庆新，潘一山，舒龙勇，等. 煤矿深部开采煤岩动力灾害多尺度分源防控理论与技术架构[J]. 煤炭学报，2018，43(7)：1 801-1 810. (QI Qingxin，PAN Yishan，SHU Longyong，et al. Theory and technical framework of prevention and control with different sources in multi-scales for coal and rock dynamic disasters in deep mining of coal mine[J]. Journal of China Coal Society，2018，43(7)：1 801- 1 810.(in Chinese))
[2]	谢和平，高峰，鞠杨. 深部岩体力学研究与探索[J]. 岩石力学与工程学报，2015，34(11)：2 161-2 178.(XIE Heping，GAO Feng，JU Yang. Research and development of rock mechanics in deep ground engineering[J]. Chinese Journal of Rock Mechanics and Engineering，2015，34(11)：2 161-2 178.(in Chinese))
[3]	齐庆新，潘一山，李海涛，等. 煤矿深部开采煤岩动力灾害防控理论基础与关键技术[J]. 煤炭学报，2020，45(5)：1 567-1 584.(QI Qingxin，PAN Yishan，LI Haitao，et al. T Theoretical basis and key technology of prevention and control of coal-rock dynamic disasters in deep coal mining[J]. Journal of China Coal Society，2020，45(5)： 1 567-1 584.(in Chinese))
[4]	王恩元，张国锐，张超林，等. 我国煤与瓦斯突出防治理论技术研究进展与展望[J]. 煤炭学报，2022，47(1)：297-322.(WANG Enyuan，ZHANG Guorui，ZHANG Chaolin，et al. Research progress and prospect on theory and technology for coal and gas outburst control and protection in China[J]. Journal of China Coal Society，2022，47(1)：297-322.(in Chinese))
[5]	何满潮. 深部的概念体系及工程评价指标[J]. 岩石力学与工程学报，2005，24(16)：2 854-2 858.(HE Manchao. Conception system and evaluation indexes for deep engineering[J]. Chinese Journal of Rock Mechanics and Engineering，2005，24(16)：2 854-2 858.(in Chinese))
[6]	谢和平，高峰，鞠杨，等. 深部开采的定量界定与分析[J]. 煤炭学报，2015，40(1)：1-10.(XIE Heping，GAO Feng，JU Yang，et al. Quantitative definition and investigation of deep mining[J]. Journal of China Coal Society，2015，40(1)：1-10.(in Chinese))
[7]	XIE H，GAO M，ZHANG R，et al. Study on the mechanical properties and mechanical response of coal mining at 1000 m or deeper[J]. Rock Mechanics and Rock Engineering，2019，52(5)：1 475-1 490.
[8]	张俊文，宋治祥. 深部砂岩三轴加卸载力学响应及其破坏特征[J]. 采矿与安全工程学报，2020，37(2)：409-418.(ZHANG Junwen，SONG Zhixiang. Mechanical response and failure characteristics of deep sandstone under triaxial loading and unloading[J]. Journal of Mining and Safety Engineering，2020，37(2)：409-418.(in Chinese))
[9]	胡建华，曾平平，杨东杰，等. 深部循环荷载下花岗岩损伤变形与细观结构分析[J]. 中国有色金属学报，2022，32(4)：1 187-1 198. (HU Jianhua，ZENG Pingping，YANG Dongjie，et al. Analysis of damage deformation and mesoscopic structure of granite under deep cyclic loading[J]. The Chinese Journal of Nonferrous Metals，2022，32(4)：1 187-1 198.(in Chinese))
[10]	陈世达，汤达祯，陶树. 原位地应力约束下煤储层自封闭作用及其成藏效应[J]. 煤炭学报，2021，46(8)：2 466-2 478.(CHEN Shida，TANG Dazhen，TAO Shu. Self-sealing of coals and CBM accumulation effect constrained by in situ stress[J]. Journal of China Coal Society，2021，46(8)：2 466-2 478.(in Chinese))
[11]	姚强岭，李学华，朱柳，等. 煤岩体地质力学参数原位测试系统开发与应用[J]. 中国矿业大学学报，2019，48(6)：1 169-1 176.(YAO Qiangling，LI Xuehua，ZHU Liu，et al. Development and application of in-situ testing system for geomechanical parameters of coal and rock mass[J]. Journal of China University of Mining and Technology，2019，48(6)：1 169-1 176.(in Chinese))
[12]	高明忠，王明耀，谢晶，等. 深部煤岩原位扰动力学行为研究[J].煤炭学报，2020，45(8)：2 691-2 703.(GAO Mingzhong，WANG Mingyao，XIE Jing，et al. In-situ disturbed mechanical behavior of deep coal rock[J]. Journal of China Coal Society，2020，45(8)： 2 691-2 703.(in Chinese))
[13]	谢和平，李存宝，高明忠，等. 深部原位岩石力学构想与初步探索[J]. 岩石力学与工程学报，2021，40(2)：217-232.(XIE Heping，LI Cunbao，GAO Mingzhong，et al. Conceptualization and preliminary research on deep in situ rock mechanics[J]. Chinese Journal of Rock Mechanics and Engineering，2021，40(2)：217-232.(in Chinese))
[14]	ZHAO Y，BI J，WANG C，et al. Effect of unloading rate on the mechanical behavior and fracture characteristics of sandstones under complex triaxial stress conditions[J]. Rock Mechanics and Rock Engineering，2021，54(9)：4 851-4 866.
[15]	SI X，GONG F. Strength-weakening effect and shear-tension failure mode transformation mechanism of rock burst for fine-grained granite under triaxial unloading compression[J]. International Journal of Rock Mechanics and Mining Sciences，2020，131：104347.
[16]	HUANG D，LI Y. Conversion of strain energy in triaxial unloading tests on marble[J]. International Journal of Rock Mechanics and Mining Sciences，2014，66：160-168.
[17]	刘刚. 卸荷路径下砂岩力学响应机理与工程应用[博士学位论文][D]. 淮南：安徽理工大学，2021.(LIU Gang. Mechanical response and engineering application of sandstone under unloading path[Ph. D. Thesis[D]. Huainan：Anhui University of Science and Technology，2021.(in Chinese))
[18]	柴文革. 围压卸载条件下花岗岩损伤演化与破坏试验研究[博士学位论文][D]. 北京：中国矿业大学，2009.(CHAI Wenge. Experimental research on damage evolution and fail of granite under unloading confining pressure[Ph. D. Thesis[D]. Beijing：China University of Mining and Technology，2009.(in Chinese))
[19]	CHEN J，JIANG D，REN S，et al. Comparison of the characteristics of rock salt exposed to loading and unloading of confining pressures[J]. Acta Geotechnica，2016，11(1)：221-230.
[20]	邱士利，冯夏庭，张传庆，等. 不同卸围压速率下深埋大理岩卸荷力学特性试验研究[J]. 岩石力学与工程学报，2010，29(9)：1 807- 1 817.(QIU Shili，FENG Xiating，ZHANG Chuanqing，et al. Experimental research on mechanical properties of deep-buried marble under different unloading rates of confining pressures[J]. Chinese Journal of Rock Mechanics and Engineering，2010，29(9)：1 807-1 817.(in Chinese))
[21]	刘永茜，韩国锋，王维华，等. 不同卸载速率下受载煤体裂隙结构演化机制[J]. 煤炭学报，2020，45(11)：3 806-3 816.(LIU Yongqian，HAN Guofeng，WANG Weihua，et al. Evolution mechanism of fracture structure of loaded coal under different unloading rates[J]. Journal of China Coal Society，2020，45(11)：3 806-3 816.(in Chinese))
[22]	王云飞，焦华喆，李震，等. 白砂岩卸围压强度与损伤破坏特征[J]. 煤炭学报，2020，45(8)：2 787-2 794.(WANG Yunfei，JIAO Huazhe，LI Zhen，et al. Strength and damage failure characteristics of white sandstone under unloading confining pressure[J]. Journal of China Coal Society，2020，45(8)：2 787-2 794.(in Chinese))
[23]	WANG Y，FENG W K，HU R L，et al. Fracture evolution and energy characteristics during marble failure under triaxial fatigue cyclic and confining pressure unloading(FC-CPU) conditions[J]. Rock Mechanics and Rock Engineering，2021，54(2)：799-818.
[24]	高明忠，王明耀，谢晶，等. 不同卸载速率下煤岩采动力学响应试验研究[J]. 工程科学与技术，2021，53(6)：54-63.(GAO Mingzhong，WANG Mingyao，XIE Jing，et al. Experimental study on the mechanical response mechanism of different unloading rate to coal rock mechanics[J]. Advanced Engineering Sciences，2021，53(6)：54-63.(in Chinese))
[25]	XIE J，GAO M，ZHANG R，et al. Gas flow characteristics of coal samples with different levels of fracture network complexity under triaxial loading and unloading conditions[J]. Journal of Petroleum science and Engineering，2020，195：107606.
[26]	鲁细根，纪洪广，余小妹，等. 三轴卸荷条件下煤体力学特性和能量耗散演化[J]. 哈尔滨工业大学学报，2022，54(2)：90-98.(LU Xigen，JI Hongguang，YU Xiaomei，et al. Mechanical characteristics and energy dissipation evolution of coal under triaxial unloading[J]. Journal of Harbin Institute of Technology，2022，54(2)：90-98.(in Chinese))
[27]	方前程，商丽，商拥辉，等. 加轴压卸围压条件下岩石的力学特性与能量特征[J]. 中南大学学报：自然科学版，2016，47(12)：4 148- 4 153.(FANG Qiancheng，SHANG Li，SHANG Yonghui，et al. Mechanical and energy characteristics of granites under unloading test[J]. Journal of Central South University：Science and Technology，2016，47(12)：4 148-4 153.(in Chinese))
[28]	LI D，SUN Z，XIE T，et al. Energy evolution characteristics of hard rock during triaxial failure with different loading and unloading paths[J]. Engineering Geology，2017，228：270-281.
[29]	MOGI K. Experimental rock mechanics[M]. [S. l.]：CRC Press，2006.
[30]	RYBACKI E，REINICKE A，MEIER T，et al. What controls the mechanical properties of shale rocks?-Part I：Strength and Young?s modulus[J]. Journal of Petroleum Science and Engineering，2015，135：702-722.
[31]	RYBACKI E，MEIER T，DRESEN G. What controls the mechanical properties of shale rocks?-Part II：Brittleness[J]. Journal of Petroleum Science and Engineering，2016，144：39-58.
[32]	XU W，LIU B，WU W. Strength and deformation behaviors of cemented tailings backfill under triaxial compression[J]. Journal of Central South University，2020，27(12)：3 531-3 543.
[33]	谢和平，高明忠，付成行，等. 深部不同深度岩石脆延转化力学行为研究[J]. 煤炭学报，2021，46(3)：701-715.(XIE Heping，GAO Mingzhong，FU Chenghang，et al. Mechanical behavior of brittle- ductile transition in rocks at different depths[J]. Journal of China Coal Society，2021，46(3)：701-715.(in Chinese))
[34]	尤明庆. 岩样三轴压缩的破坏形式和Coulomb强度准则[J]. 地质力学学报，2002，8(2)：179-185.(YOU Mingqing. Destroy character and coulomb criterion of rock specimen in pseudo-triaxal compression[J]. Journal of Geomechanics，2002，8(2)：179-185.(in Chinese))
[35]	张向东，蔡冀奇，唐楠楠，等. 深部砂岩力学特性试验与本构模型[J]. 煤炭学报，2019，44(7)：2 087-2 093.(ZHANG Xiangdong，CAI Jiqi，TANG Nannan，et al. Experimental study on mechanical properties of deep sandstone and its constitutive mode[J]. Journal of China Coal Society，2019，44(7)：2 087-2 093.(in Chinese))
[36]	张黎明，王在泉，石磊. 硬质岩石卸荷破坏特性试验研究[J]. 岩石力学与工程学报，2011，30(10)：2 012-2 018.(ZHANG Liming，WANG Zaiquan，SHI Lei，et al. Experimental study of hard rock failure characteristic under unloading condition[J]. Chinese Journal of Rock Mechanics and Engineering，2011，30(10)：2 012-2 018.(in Chinese))
[37]	李地元，孙志，李夕兵，等. 不同应力路径下花岗岩三轴加卸载力学响应及其破坏特征[J]. 岩石力学与工程学报，2016，35(增2)：3 449-3 457.(LI Diyuan，SUN Zhi，LI Xibing，et al. Mechanical response and failure characteristics of granite under different stress paths in triaxial loading and unloading conditions[J]. Chinese Journal of Rock Mechanics and Engineering，2016，35(Supp.2)：3 449-3 457. (in Chinese))
[38]	刘炜震，郭忠平，黄万朋，等. 不同温度养护后胶结充填体三轴卸围压力学特性试验研究[J]. 岩石力学与工程学报，2022，41(11)：2 268-2 282.(LIU Wei，GUO Zhongping，HUANG Wangpeng，et al. Experimental study on mechanical characteristics of cemented backfill under triaxial unloading confining pressure after cured at different temperatures[J]. Chinese Journal of Rock Mechanics and Engineering，2022，41(11)：2 268-2 282.(in Chinese))